T3MK7516 Altronix Trove3 Mercury Kits Installation Guide

Access & Power Integration
Altronix/Trove3 Mercury Kits
Models Include:

T3MK7516 Altronix Trove3 Mercury Kits

T3MK7516
16 Door Kit with Fused Outputs
Fully assembled kit includes:
– Trove3 enclosure with TM3 Altronix/Mercury backplane
– One (1) AL1024ULXB2 – Power Supply/Charger
– One (1) AL1012ULXB – Power Supply/Charger
– Two (2) ACM8 – Fuse Protected Access Power Controllers
– One (1) PD8UL – Fuse Protected Power Distribution Module
– One (1) Rocker Switch Bracket with Two (2) Rocker Switches
(Not evaluated by UL)| T3MK7716
16 Door Kit with Fused Outputs
Fully assembled kit includes:
– Trove3 enclosure with TM3 Altronix/Mercury backplane
– Two (2) AL1024ULXB2 – Power Supply/Chargers
– Two (2) ACM8 – Fuse Protected Access Power Controllers
– Two (2) PD8UL – Fuse Protected Power Distribution Modules
– One (1) Rocker Switch Bracket with Two (2) Rocker Switches
(Not evaluated by UL)
---|---
T3MK7516D
16 Door Kit with PTC Outputs
Fully assembled kit includes:
– Trove3 enclosure with TM3 Altronix/Mercury backplane
– One (1) AL1024ULXB2 – Power Supply/Charger
– One (1) AL1012ULXB – Power Supply/Charger
– Two (2) ACM8CB – PTC Protected Access Power Controllers
– One (1) PD8ULCB – PTC Protected Power Distribution Module
– One (1) Rocker Switch Bracket with Two (2) Rocker Switches
(Not evaluated by UL)| T3MK7716D
16 Door Kit with PTC Outputs
Fully assembled kit includes:
– Trove3 enclosure with TM3 Altronix/Mercury backplane
– Two (2) AL1024ULXB2 – Power Supply/Chargers
– Two (2) ACM8CB – PTC Protected Access Power Controllers
– Two (2) PD8ULCB – PTC Protected Power Distribution Modules
– One (1) Rocker Switch Bracket with Two (2) Rocker Switches
(Not evaluated by UL)

All components of these Trove kits are UL Listed as sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
Installation Guide
All registered trademarks are property of their respective owners.
Rev. T3MKL113021
Installing Company: ____ Service Rep. Name:
Address: ___ Phone #: ____

Overview:

Altronix Trove Mercury kits are pre-assembled and consist of Trove3M3 enclosure/backplane with factory-installed Altronix power supply/ charger(s) and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to sixteen (16) doors in a single enclosure.

Configuration Chart:

Hardware and Accessories:

• Two (2) tamper switches (Altronix Model TS112 or equivalent).
• Cam lock.
• Battery leads.

Mechanical:

• 16 Gauge enclosure with ample knockouts for convenient access.
• Enclosure Dimensions (H x W x D): 36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm).

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only.

1. Remove the backplane from the enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level, and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switches (Altronix Model TS112 or equivalent) in the desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect the tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
   To activate alarm signal open the door of the enclosure.

4. Mount Mercury boards to the backplane, refer to pg. 3, 4.

5. Refer to the ULXB Power Supply/Charger Installation Guide for AL1024ULXB2, AL1012ULXB, and corresponding Sub-Assembly Installation Guides for PD8UL(CB) and ACM8(CB) for further installation instructions.

6. Position the Mercury access controller module over corresponding spacers and depress onto snap-on spacers (Fig. 2-3, pg. 3-4).

7. Mount backplane to an enclosure with hardware.

Hardware:

Snap On Spacer | 5/16” Pan Head Screw | Lock Nut

T3MK7516 and T3MK7516D: Configuration of Mercury Boards:

1. Fasten snap-on spacers onto metal pems configuration (A) (B) of the backplane depending on the access controller (Fig. 2, pg. 3).
2. Position the access controller module over the corresponding spacers and depress onto snap-on spacers (Fig. 2a, pg. 3).
3. Mount backplane to the enclosure with hardware.

Access Controller Position Chart for the Following Models:

T3MK7716 and T3MK7716D: Configuration of Mercury Boards on TM3:

1. Fasten snap-on spacers onto metal pems configuration (A) (B) of the backplane depending on the access controller (Fig. 3, pg. 4).
2. Position the access controller module over the corresponding spacers and depress onto snap-on spacers (Fig. 3a, pg. 4).
3. Mount backplane to the enclosure with hardware.

Access Controller Position Chart for the Following Models:

Notes:

TM3 Dimensions
34” x 28” x 0.3125” (863.6mm x 711.2mm x 7.9mm)

Trove3 Enclosure Dimensions (H x W x D approximate):
36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm)

Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 web site: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty
IITrove3M3 ULXB Kit Series
K30U

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>