Carlson 3030 DS Easy Close Walk Through Gate with Small Pet Door Instruction Manual

Carlson 3030 DS Easy Close Walk Through Gate with Small Pet Door

Easy Close Walk-Through Gate with Small Pet Door

READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
KEEP INSTRUCTIONS FOR FUTURE USE.

• www.carlsonpetproducts.com

• Carlson Pet Products, Inc.
  3200 Corporate Center Drive, Suite 105 / Burnsville, MN 55306, USA/, E.-U. /, EE. UU. e

• 952.435.1 os4

• Made in China/Fabrique en Chine/Hecha en China

Before Assembly

PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:

• A Gate Frame(1)
• B Wa11 Cups(4)
• C 1″ Wall Mount Screws (4) (requires a Phillips/crosshead screwdriver)
• D Threaded Spindle Rods (4)

BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using. The safety of your pet and/or child is your responsibility. Please keep these instructions for your reference.

REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the (4) threaded spindle rods to depressurize the gate from its doorway or opening. Then, gently pull or push the gate free from its doorway or opening.

CARE AND MAINTENANCE

Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged.
Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.

90 DAYS LIMITED WARRANTY

If, during the first 90 days after consumer purchase of the item, under reasonable and non-commercial use and conditions of maintenance, it fails while owned by the original purchaser because of the quality of materials or workmanship of finish and assembly, Carlson Pet Products, Inc. will replace or repair it at Carlson’s option. PROOF OF PURCHASE REQUIRED.

Assembling and Installing Your Gate

• Locate the (4) threaded spindle rods (D) Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot
  NOTE: You will notice a slight gap between the gate door latch and the frame. This is not a defect. Your gate is a pressure mounted gate and this gap will disappear once you tighten your gate in its opening.

• Insert the (4) threaded spindle rods into the holes at each of the four corners of the gate.
  NOTE: It may be necessary to hold the threaded spindle rods or rubber feet while rotating the adjustment wheels to ensure the entire unit does not rotate.

• Position the gate (A) so that it is level and centered within your doorway or opening. Rotate the adjustment wheels on the threaded spindle rods in the opposite direction as in Step 1, expanding the gap between the rubber foot and the adjustment wheel. Expand each of the (4) threaded spindle rods until they make contact with the doorway or opening. Do not fully tighten the threaded spindle rods yet.
  NOTE: The gap between the gate and wall should not exceed more than 2.5 inches. Make the appropriate adjustment to ensure you have installed your gate safely.

• When you are satisfied with the general placement of your gate, fully tighten the threaded spindle rods attached to the lower corners of the gate by further rotating the adjustment wheels. Continue by tightening the upper threaded spindle rods. As you tighten the threaded spindle rods, you will notice the gap between the door frame and the secure lift latch begin to narrow. In order for the gate to function properly, stop tightening the upper threaded spindle rods just before the outer housing of the secure lift latch and the receiving component touch.
  NOTE: There should be equal spacing among each of the (4) threaded spindle rods. Make the appropriate adjustment to ensure you have installed your gate safely.

Operating the Door Latch

• Pull up on the finger loop while simulataneously pushing down the lock button. These two actions combined will disengage the lock and allow the gate to open freely in either direction. The gate should open with minimal effort. To close, simply push or pull the door back into its original position. The latch will re-engage automatically and lock the door into its closed position.
  NOTE: If your gate door is not properly engaging with the receiving component, ensure that your gate is level, square to the door frame, mounted properly, and that you have equally tightened the threaded spindle rods.

Positioning and Attaching Wall Cups

• After you have mounted your gate, and you are satisfied with its positioning, draw a circle on the surtace of your doorway or opening around the perimeter of the (4) rubber feet.
  Next, completely remove the gate from the opening by loosening each of the (4) threaded spindle rods to depressurize the gate.

• With the gate fully removed, you can now use the circles you marked during Step 1 as guides for screwing in your (4) wall cups (B). Center each of the wall cups within the guide circles and use the provided self-tapping 25mm screws (C) to fasten them in place via the hole through the center of each wall cup.

• Reinstall your gate in the doorway or opening according to the instructions, using the newly installed wall cups as anchoring points for the (4) threaded spindle rods.

Adding a Gate Extension

Remove the top and bottom threaded spindle rods.
Assemble the gate and extension as illustrated. Reposition the gate and fit in accordance with the gate fitting.

NOTE: It is preferable to install any extensions on the hinge side of the gate .

Need more width? Additional extensions sold separately www.caitsonpetproducts.com

WARNING

NOTE: The gap between the gate and wall should not exceed more than 2.5 inches.

• INSTALLACCORDING TO MANUFACTURES INSTRUCTIONS.

• NOT RECOMMENDED FOR USE WITH CHILDREN.

• TO PREVENT SERIOUS INJURY OR DEATH, SECURELY INSTALL GATE AND USE ACCORDING TO MANUFACTURER’S INSTRUCTIONS.

• CHILDREN HAVE DIED OR BEEN SERIOUSLY INJURED WHEN GATES ARE NOT SECURELY INSTALLED.
  ALWAYS INSTALL AND USE GATE AS DIRECTED USING ALL REQUIRED PARTS.

• YOU MUST INSTALL WALL CUPS TO KEEP GATE IN PLACE. WITHOUT WALL CUPS, CHILD CAN PUSH OUT
  AND ESCAPE.

• NEVER STACK GATES ON TOP OF EACH OTHER TO FORM A TALLER BARRIER. THIS COULD RESULT IN SERIOUS INJURY OR DEATH.

• INTENDED FOR USE WITH CHILDREN BETWEEN 6 AND 24 MONTHS.

• STOP USING WHEN A CHILD OR PET CAN CLIMB OVER OR DISLODGE THE GATE.

• USE ONLY WITH THE LOCKING/LATCHING MECHANISM SECURELY ENGAGED.

• TO PREVENT FALLS, NEVER USE AT TOP OF STAI RS.

• NEVER USE TO KEEP CHILD OR PET AWAY FROM POOL.

• ALWAYS ENSURE THE GATE IS RESTING AGAINSTTHE FLOOR BEFORE BEGINNING INSTALLATION.

• THIS IS A PET GATE, BUT WHEN USED WITH CHILDREN, THE SMALL PET DOOR MUST REMAIN CLOSED AND SECURELY LATCHED.

• STRANGULATION HAZARD: PETS CAN FORCE THEMSELVES INTO VERY SMALL OPENINGS; USE THIS GATE WITH PETS WHOSE HEADS WILL NOT FIT INTO OPENINGS IN THE GATE, BETWEEN THE GATE AND FLOOR, OR BETWEEN THE GATE AND WALL.

• THIS PRODUCT WILL NOT NECESSARILY PREVENT ALL ACCIDENTS. NEVER LEAVE CHILD OR PET UNATTENDED.

• CHECK THE GATE REGULARLY TO SEE IF ALL THE HARDWARE AND MOUNTINGS ARE TIGHTENED.

• DO NOT USE IF ANY COMPONENTS ARE MISSING OR DAMAGED.

•  ADULT ASSEMBLY REQUIRED.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>