Carlson 0938 PW 41 Extra Tall Walk Thru Pet Gate Instruction Manual

June 13, 2024
Carlson

Carlson 0938 PW 41 Extra Tall Walk Thru Pet Gate Instruction Manual
Extra Tall Walk Thru Pet Gate

READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE.

Before Assembly

PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:

  • A.12 Extension (1)

  • B.GateFrame (1)

  • C.6 Excension (1)

  • D.wall Cups ()

  • E.1 Wall Mount Screws (4)

  • F.Threaded Spindle Rods (4)

Note

MODEL NO. MAX SIZE
0938PW 29<—>38.5in,} 41intall
0945PW 29<—>50in,§ 47in tall

BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using. The safety of your pet and/or child is your responsibility. Please keep these instructions for your reference.

IMPORTANT

  • Never use more than two extensions per side of gate.
  • If hardware mounting to a surface offer than drywall o wood, please consult with a professional about installation.
  • Base locks are to be used at all times, on both sides of the gate.

REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the (4) threaded spindle rods to depressurize the gate from its doorway or opening. Then, gently pull or push the gate free from its doorway or opening.

CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.

Assembling and Installing Your Gate

Step 1
Product Instruction
Locate the (4) threaded spindle rods (F) Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot.

NOTE: You will notice a slight gap between the gate door latch and the frame. This is not a defect. Your gate is a pressure mounted gate and this gap will disappear once you tighten your gate in its opening.

Step 2
Product Instruction
Insert the (4) threaded spindle rods into the holes at each of the four corners of the gate

NOTE: The ends of the gate frame are not threaded. The threaded spindle rods should slide into the end of the frame tubes without any resistance.

NOTE: It may be necessary to hold the threaded spindle rods or rubber feet while rotating the adjustment wheels to ensure the entire unit does not rotate

Step 3
Product Instruction
Position the gate (B) so that it is level and centered within your doorway or opening. Rotate the adjustment wheels on the threaded spindle rods in the opposite direction as in Step 1, expanding the gap between the rubber foot and the adjustment wheel. Expand each of the (4) threaded spindle rods until they make contact with the doorway or opening. Do not fully tighten the threaded spindle rods yet

NOTE: The gap between the gate and wall should not exceed more than 2.5 inches. Make the appropriate adjustment to ensure you have installed your gate safely

Step 4
Product Instruction
When you are satisfied with the general placement of your gate, fully tighten the threaded spindle rods attached to the lower corners of the gate by further rotating the adjustment wheels. Continue by tightening the upper threaded spindle rods. As you tighten the threaded spindle rods, you will notice the gap between the door frame and the secure slide latch begin to narrow. In order for the gate to function properly, stop tightening the upper threaded spindle rods just before the outer housing of the secure slide latch and the receiving component touch.

NOTE : There should be equal spacing among each of the (4) threaded spindle rods. Make the appropriate adjustment to ensure you have installed your gate safely

Operating the Door Latch

Step 1
Product Instruction
Push the circular button on the secure slide latch while simultaneously pulling back. These two actions combined will disengage the lock and allow the gate to open freely. Push or pull to open the gate door. To close, simply push or pull the door back into its original position. The secure slide latch will re-engage automatically and lock the door into its closed position.

NOTE: If your secure slide latch is not properly engaging with the receiving component, ensure that your gate is level, mounted properly. and that you have not over-tightened the threaded spindle rods

Step 2
Product Instruction
At the bottom of the gate door, rotate the base lock to the horizontal position to allow the door to swing open.

NOTE: Place lock down on side occupied by the child

Positioning and Attaching Wall Cups

Step 1
Product Instruction
After you have mounted your gate, and you are satisfied with its positioning, draw a circle on the surface of your doorway or opening around the perimeter of the (4) rubber feet

Step 2
Product Instruction
With the gate fully removed, you can now use the circles you marked during Step 1 as guides for screwing in your (4) wall cups (D) Center each of the wall cups within the guide circles and use the provided self-tapping 25mm screws (E) to fasten them in place via the hole through the center of each wall cup.

**Step 3

** Reinstall your gate in the doorway or opening according to the instructions, using the newly installed wall cups as anchoring points for the (4) threaded spindle rods

Adding a Gate Extension

Product Instruction
Remove the top and botto threaded spindle rods.

Assemble the gate and extension as illustrated. Reposition the gate and fit in accordance with the gate fitting

NOTE: It is preferable to install any extensions on the hinge side of the gate

Extensions List

MODEL NO. 4″ 6″ 8″ 12″ MAX SIZE
0938 PW 29<—>38.5in,} 41intall
0945 PW 29<—>50in,§ 47in tall

Need more width? Additional extensions sold separately
www.arlsonpetproducts.com

90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable and non-commercial use and conditions of maintenance, it fails while owned by the original purchaser because of the quality of materials or workmanship of finish and assembly, Carlson Pet Products, Inc. will replace or repair it at Carlson’s option. PROOF OF PURCHASE REQUIRED.

WARNING

NOTE: The gap between the gate and wall should not exceed more than 2.5 inches.

  • INSTALLACCORDING TO MANUFACTURES INSTRUCTIONS.
  • NOT RECOMMENDED FOR USE WITH CHILDREN.
  • T0 PREVENT SERIOUS INJURY OR DEATH, SECURELY INSTALL GATE AND USE ACCORDING TO MANUFACTURER’S INSTRUCTIONS.
  • CHILDREN HAVE DIED OR BEEN SERIOUSLY INJURED WHEN GATES ARE NOT SECURELY INSTALLED. ALWAYS INSTALLAND USE GATE AS DIRECTED USING ALL REQUIRED PARTS.
  • YOU MUST INSTALL WALL CUPSTO KEEP GATE IN PLACE. WITHOUT WALL CUPS, CHILD CAN PUSH OUT AND ESCAPE.
  • NEVER STACK GATES ONTOP OF EACH OTHER TO FORM ATALLER BARRIER. THIS COULD RESULTIN SERIOUS INJURY OR DEATH.] INTENDED FOR USE WITH CHILDREN BETWEEN 6 AND 24 MONTHS. STOP USING WHEN A CHILD OR PET CAN CLIMB OVER OR DISLODGE THE GATE.
  • USE ONLY WITH THE LOCKING/LATCHING MECHANISM SECURELY ENGAGED. ® TO PREVENT FALLS, NEVER USE ATTOP OF STAIRS.
  • NEVER USE TO KEEP CHILD OR PETAWAY FROM POOL.
  • ALWAYS ENSURE THE GATE IS RESTING AGAINST THE FLOOR BEFORE BEGINNING INSTALLATION.
  • THIS IS APET GATE, BUTWHEN USED WITH CHILDREN, THE SMALL PETDOOR MUST REMAIN CLOSED AND SECURELY LATCHED.
  • STRANGULATION HAZARD: PETS CAN FORCE THEMSELVES INTO VERY SMALL OPENINGS; USETHIS GATE WITH PETS WHOSE HEADS WILLNOT FIT INTO OPENINGS IN THE GATE, BETWEEN THE GATE AND FLOOR, OR BETWEEN THE GATE AND WALL.
  • THIS PRODUCT WILL NOT NECESSARILY PREVENT ALL ACCIDENTS. NEVER LEAVE CHILD OR PETUNATTENDED.
  • CHECK THE GATE REGULARLY TO SEE IF ALLTHE HARDWARE AND MOUNTINGS ARE TIGHTENED.
  • DO NOT USE IF ANY COMPONENTS ARE MISSING OR DAMAGED.
  • ADULTASSEMBLY REQUIRED.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Carlson User Manuals

Related Manuals