Carlson Pet 2450 Super Wide Convertible Pet Gate Instruction Manual
- June 14, 2024
- Carlson Pet
Table of Contents
Carlson Pet 2450 Super Wide Convertible Pet Gate
Before Assembly
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
-
Convertible Gate Frame (5 panels) (1 J)
-
Plastic Mounting Brackets (4 -Attached to gate)\
-
Wall Mounting Screws (8) (requires a Phillips/crosshead screwdriver)
BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using. The safety of your pet and/or child is your responsibility. Please keep these instructions for your reference.
IMPORTANT
- The four mounting brackets must be used in securing the gate to the wall. These brackets prevent the gate from dislodging from its opening and becoming unstable.
- If hardware mounting to a surface other than drywall or wood, please consult with a professional about installation.
- This gate is designed to lit maximum width openings 120 inches without the wall mounts and 124 inches when the wall mounts are included.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components. Do not use ii any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable and non-commercial use and conditions of maintenance, it fails while owned by the original purchaser because of the quality of materials or workmanship of finish and assembly, Carlson Pet Products, Inc. will replace or repair it at Carlson’s option. PROOF OF PURCHASE REQUIRED.
Option A: Installing Your Gate Between Two Walls
Unfold the gate frame by turning the locking knobs counter clockwise at each pivoting joint. Loosen the knobs enough to allow the gate to swing open freely without fully removing the knobs.
Use a Phillips/crosshead screwdriver to fix the wall mounting bracket to the wall. Repeat for all four brackets. Arrange the panels to your desired configuration, then tighten all of the locking knobs.
Option B: Installing Your Gate as a Pet Yard
Unfold the gate frame by turning the locking knobs counter clockwise at each pivoting joint. loosen the knobs enough to allow the gate to swing open freely without fully removing the knobs. Configure your pet yard into your desired shape.
NOTE: THIS CONFIGURATION REQUIRES THE PURCHASE OF ADDITIONAL PANELS (see page 11). Please call 952-435· 1O84 to purchase additional panels.
Remove the 2 vertical tubes at each end of the gate by twisting the locking knobs completely off and pulling the tubes up through the top. Also remove the mounting brackets at this time.
NOTE: Store extra parts for future use.
Join the free ends of the pet yard together at the plastic joints.
Insert one of the previously removed metal pivot bars through the opening created by joining the upper plastic joints. Guide the metal pivot bar downward into the circular housing on the lower plastic joint.
Reassemble the upper locking joint by adding one of the previously removed toothed disks and locking knobs.
Tighten each of the locking knobs by turning them clockwise, fixing the pet yard into the configuration you have chosen. To position the pet yard into a new configuration or shape, simply loosen each of the locking knobs, adjust and re-tighten.
NOTE: When increasing or decreasing the size of your pen, panels must be added or removed in multiples of two. ADDITIONAL PANELS SOLO SEPARATELY.
Operating the Door Latch
Push both sides of the slide lock upwards along the slotted opening while simultaneously pulling upwards on the metal lift latch until the latch raises above the gate’s door frame. To re-lock the gate, close the door completely and drop the metal lift latch back into place. The slide lock will return to its locked position on its own.
Step 1
Loosen all of the locking knobs so the panels can move freely and become flexible at the joints.
Step 2
Remove one of the locking knobs from the gate and remove one vertical tube.
Step 3
You will now be able to pull the two plastic joints and the top and bottom of the gate apart.
Step 4
Fold and put away.
Pet Yard Extension Kit
To extend your Pet Yard into a larger shape, please purchase: Model 0028 (includes 2 panels)
WARNING
-
INSTALL ACCORDING TO MANUFACTURES INSTRUCTIONS.
-
NOT RECOMMENDED FOR USE WITH CHILDREN.
-
TO PREVENT SERIOUS INJURY OR DEATH, SECURELY INSTALL GATE AND USE ACCORDING TO MANUFACTURER’S INSTRUCTIONS.
-
CHILDREN HAVE DIED OR BEEN SERIOUSLY INJURED WHEN GATES ARE NOT SECURELY
INSTALLED.ALWAYS INSTALL AND USE GATE AS DIRECTED USING ALL REQUIRED PARTS. -
NEVER STACK GATES ON TOP OF EACH OTHER TO FORM A TALLER BARRIER. THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
-
INTENDED FOR USE WITH CHILDREN BETWEEN 6 AND 24 MONTHS.
-
STOP USING WHEN A CHILD OR PET CAN CLIMB OVER OR DISLODGE THE GATE.
-
USE ONLY WITH THE LOCKING/LATCHING MECHANISM SECURELY ENGAGED.
-
TO PREVENT FALLS, NEVER USE ATTOP OF STAIRS.
-
NEVER USE TO KEEP CHILD OR PET AWAY FROM POOL.
-
ALWAYS ENSURE THE GATE IS RESTING AGAINSTTHE FLOOR BEFORE BEGINNING INSTALLATION.
-
STRANGULATION HAZARD: PETS CAN FORCE THEMSELVES INTO VERY SMALL OPENINGS; USE THIS GATE WITH PETS WHOSE HEADS WILL NOT FIT INTO OPENINGS IN THE GATE, BETWEEN THE GATE AND FLOOR, OR BETWEEN THE GATE AND WALL.
-
THIS PRODUCT WILL NOT NECESSARILY PREVENT ALL ACCIDENTS. NEVER LEAVE CHILD OR PET UNATTENDED.
-
CHECK THE GATE REGULARLYTO SEE IF ALL THE HARDWARE AND MOUNTINGS ARE TIGHTENED.
-
DO NOT USE IF ANY COMPONENTS ARE MISSING OR DAMAGED.
-
ADULT ASSEMBLY REQUIRED.
-
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. L.!J KEEP INSTRUCTIONS FOR FUTURE USE.
Carlson Pet Products, Inc.
3200 Corporate Center Drive, Suite 105 / Burnsville, MN 55306, USA/, E.-U. /,
EE. UU .
952.435.1084
Made in China /Fabrique en Chi ne/ Hecha en China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>