Tiger Stop CON5 Tablet Stand Assembly Instruction Manual
- June 1, 2024
- Tiger Stop
Table of Contents
Tablet Package
Installation Manual
CON5 Tablet Stand Assembly
SAFETY FIRST!
IMPORTANT SAFETY INFORMATION. READ ALL WARNINGS BEFORE OPERATING THIS PRODUCT.
GENERAL WARNINGS
WARNING: Installation of your TigerStop® Product must be done by a person
trained in the safe design and installation of automation products, and in the
safe operation of power equipment. Ensure that such installation meets all
legally required safety requirements and guidelines, and that proper guarding
and safety devices are provided on all sides of the equipment to preclude
unintended access during operation. Consult with and follow the
recommendations of a qualified safety engineer.
WARNING: TigerStop® Products are components intended for use in
conjunction with potentially dangerous machinery.
The use of TigerStop® Products does not make other machinery safe. TigerStop®
Products are not intended to substitute, in any manner, for safe operating
practices in general, or for safety features present in other machines
designed to make those machines as safe as possible. TIGERSTOP® PRODUCTS, IF
USED OR INSTALLED IMPROPERLY, MAY CAUSE PERSONAL INJURY OR DEATH AND SHOULD
ONLY BE OPERATED BY PERSONS TRAINED IN THEIR SAFE OPERATING PROCEDURES.
Illustrations of TigerStop® Products in use do not show, and are not intended
to show, all safety features and practices necessary for their safe operation.
INSTALLATION WARNINGS
WARNING: TigerStop® Products must be installed in accordance with all
local, state, and federal regulations. Only personproperly trained in the safe
design and installation of automation machinery and related power equipment
should install TigerStop® Products onto other equipment, to ensure a safe and
proper work station. TigerStop® Products should not be operated without proper
training, both in the operation of TigerStop® Products, and in the operation
of related equipment.
IMPORTANT CAUTION:
The motor box (compartment) contains DC voltage with potentially FATAL
amperage. NEVER attempt any unauthorized acinside the motor box.
INTERCONNECTS
WARNING: Using a TigerStop® interconnect does not relieve you of the responsibility for making sure that your saw or other tool has all the necessary safety equipment in place. All installations must meet all legally required safety requirements and guidelines. Installation and training should be done following the recommendations of a qualified safety engineer.
OPERATION
DANGER: This machine can start, move and stop automatically. Keep hands
and loose clothing clear of moving parts while operating. Moving parts can
crush and cut. When used with a saw or other cutting equipment, bodily injury
and death may result if operated without safety guards on all machines. Do not
operate with guards removed. Operators must wear adequate eye and ear
protection.
IMPORTANT SAFETY INFORMATION. READ ALL WARNINGS BEFORE OPERATING THIS PRODUCT.
DANGER! Don’t get pinched by the push feeder. Keep your hands away when
in motion!
Keep the work area clean and well lighted to avoid accidental injury.
Do not use TigerStop® machines in a dangerous environment. Using power tools
in damp or wet locations or in rain can cause shock or electrocution.
Do not operate near flammable liquids or in gaseous or explosive atmospheres!
Wear proper apparel, no loose clothes, long hair or jewelry which could get
pulled into moving machinery or materials. Wear non slip footwear, safety
glasses, ear protection and a dust mask.
Use only 3-wire extension cords that have 3-prong grounding type plugs and
3-pole receptacles that accept the tools plug for 120VAC. Use only 5-wire
cords and plugs when using 3 phase.”
Do not open motor compartment or controller keypad. DC Voltage with
potentially FATAL amperage! Disconnect power before servicing. No user-
serviceable parts inside.
DO NOT operate this or any machine under the influence of drugs or alcohol!
No one should operate this machine except for fully qualified personnel.
READ THE MANUAL!
Contact Us
Offices
TigerStop Global Headquarters
12909 NE 95th Street
Vancouver, WA 98682-2426
TigerStop Europe
Bedrijvenstraat 17 NL-7641 AM
Wierden, Netherlands| Call Us
TigerStop Customer Service
Phone: +1 (360) 448 6102
TigerStop Sales
Phone: +1 (360) 254 0661 ext 2
TigerStop Headquarters
Phone: +1 (360) 254 0661
Fax: +1 (360) 260 0755
TigerStop Europe
Phone: +31 546 575 171
TigerStop Europe | Sales
Phone: +31 546 575 171 (option 2)
TigerStop Europe | Service
Phone: +31 546 575 171 (option 1)
TigerStop Mexico
Phone: +1 (360) 254 0661| Email Us
TigerStop Customer Service
Email: [email protected]
TigerStop Sales
Email: [email protected]
TigerStop Headquarters
Email: [email protected]
TigerStop Europe
Email: [email protected]
TigerStop Europe | Sales
Email: [email protected]
TigerStop Europe | Service
Email: [email protected]
Follow Us
---|---|---
Parts Inventory
Tablet Stand Assembly
| PART | DESCRIPTION (NUMBER) | QUANTITY |
|---|---|---|
| Tablet Stand Top | ||
| (M1803) | 1 | |
| Square Tube | ||
| (M1808) | 1 | |
| Round Tube | ||
| (M1807) | 1 | |
| Tablet Stand |
Base Half-Bracket
(M10070)| 2
| M6x14mm
Socket-Head Screw
(F7216)| 1
| M6x10mm
Socket-Head Screw
(F7208)| 1
| M8x50mm
Hex-Head Screw
(F9827)| 1
| M8x45mm
Hex-Head Screw
(F9826)| 2
| Spacer
(F6702)|
| M8x35mm
T-Bolt
(F0184)| 2
| M8
Flange Nut
(F0419)| 5
Tablet Package
| PART | DESCRIPTION (NUMBER) | QUANTITY |
|---|---|---|
| Tablet | ||
| (E0008) | 1 | |
| Tablet Case | ||
| (SB9042) | 1 | |
| Serial Data Cable | ||
| (J8015) | 1 | |
| USB to Serial Converter | ||
| (J3600) | 1 | |
| USB Power Cable | ||
| (J9909) | 1 | |
| USB Charger | ||
| (J9913) | 1 |
Tablet Stand Assembly
The tablet stand mounts the Tablet to any support structure.
The tablet stand pivots between 0-90° with the base hardware.
- Place the Tablet Stand Base Brackets against the Round Tube and insert two M8x45mm Hex-Head Screws through all three parts.
- Fasten the Base Brackets to the Round Tube with M8 Flange Nuts.
- Insert one M8x35mm T-bolt through each vertical slot in the Tablet Stand Base Brackets. Fasten with M8 Flange Nuts
- Insert the Round Tube into the Square Tube and fasten with an M6x14mm Socket-Head Screw.
- Place the Spacer between the Square Tube’s holes.
- Connect the Spacer, Tablet Stand Top, and Tube with an M8x50mm Hex-Head Screw.
- Fasten with an M8 Flange Nut.
- Attach the Tablet Case to the Tablet Stand Top. Use the four included fasteners on the back of the Tablet Case in a square pattern.
Connecting the Tablet
Cable Routing
When routing cables, adhere to the below guidelines:
- Keep data cables and power cables at least 2” (50mm) apart.
- Keep cables away from dust collection systems.
- Keep data cables away from florescent lighting and any electrical noise generating devices.
- Do not over-tighten any zip ties or other cable restraints.
- Route all cables away from any crushing or pinching hazards.
Cable Connections
- Plug the USB-to-Serial Converter into the USB Hub on the back of the Tablet Case.
- Connect the other end of the USB-to-Serial Converter to the Serial Data Cable.
- Connect the Serial Data Cable to the 9-pin RS232 port on the Amplifier.
- Plug the USB-B (smaller) end of the USB Power Cable into the USB Hub.
- Plug the other end of the USB Power Cable into the USB Wall Charger.
- Plug the USB Wall Charger into a power outlet.
- Turn on the Tablet.
• The Tablet is ready to work.
TigerStop Product
COMPARISON CHART
Product| Max Load Push| Power Requirement| Drive Type|
Accuracy| Working Length
---|---|---|---|---|---
TigerSPC| Caliper| 2 AA
Battery| N/A| +/- .008”
+/- 0.2mm| 0’ – 20’
0m – 6m
SawGear| Stop Only| 110 Vac| 32mm Belt
Steel Reinforced| +/- .008”
+/- 0.2mm| 8’ – 20’
2.4m – 6m
SawGear Touch| Stop Only| 110 Vac| 32mm Belt
Steel Reinforced| +/- .008”
+/- 0.2mm| 8’ – 20’
2.4m – 6m
TigerFence| Stop Only| 110 / 240 Vac| 3/4”
Hi-Lead Screw| +/- .003”
+/- 0.08mm| 51” or 70”
1.29m – 1.77m
TigerStop| 90lbs/41kg
Solid Tables
180lbs/81kg
Roller Tables| 110 / 240 Vac| 32mm Belt
Steel Reinforced
+/- .004”| +/- .004”
+/- 0.1mm| 4’ -30’
1.2m – 9.1m
TigerRack| 300lbs/136kg
Solid Tables
720lbs/327kg
Roller Tables| 240 Vac| Rack & Pinion| +/- .008”
+/- 0.2mm| 12’ – 108’
3.7m – 32.9m
TigerTurbo| 350lbs/159kg
Solid Tables
840lbs/381kg
Roller Tables| 240 Vac| 75mm Belt
Steel Reinforced| +/- .008”
+/- 0.2mm| 12’ – 42’
3.7m – 12.8m
HeavyDuty 2| 490lbs/222kg
Solid Tables
2100lbs/952kg
Roller Tables| 240 Vac| Rack & Pinion| +/- .008”
+/- 0.2mm| 12’ – 108’
3.7m – 32.9m
TigerSaw 1000| 490lbs/222kg
Solid Tables
2100lbs/952kg
Roller Tables| 208 / 480 Vac| 32 or 75mm Belt
Steel Reinforced
or Rack & Pinion| +/- .012”
+/- 0.3mm| 8’ – 108’
2.4m – 32.9m
TigerSaw 2000| 490lbs/222kg
Solid Tables
2100lbs/952kg
Roller Tables| 208 / 480 Vac| 32 or 75mm Belt
Steel Reinforced
or Rack & Pinion| +/- .012”
+/- 0.3mm| 8’- 108’
2.4m – 32.9m
TigerSaw MiterXL| 490lbs/222kg
Solid Tables
2100lbs/952kg
Roller Tables| 400 – 480 Vac| 32 or 75mm Belt
Steel Reinforced
or Rack & Pinion| +/- 0.1 º
+/- .012”| 8’ – 108’
2.4m – 32.9m
AutoLoader| 5×100 LBS
5×45.36 KG| 110 / 240 Vac
208 / 480 Vac| Pneumatic| N/A| 4’ – 30’
1.2m – 9.1m
TigerStop USA
12909 NE 95th Street
Vancouver, WA 98682
P: 360.254.0661 • F: 360.260.0755
TigerStop Europe
Bedrijvenstraat 17 NL-7641 AM Wierden
Nederland
P: +31.546.57.51.71
• Made in USA from domestic and foreign components.