AERCO 24793-1 Edge Controller Instruction Manual
- June 1, 2024
- AERCO
Table of Contents
AERCO 24793-1 Edge Controller
AERtrim Activation on Edge Controller
Step-by-Step Activation Instructions
-
Check if O 2 Monitoring Kit is installed on the unit.
If the O2 field is blank, the kit is not installed. If O2 has values, skip step 2. (Calibration > Input/Output > O2 Sensor) -
If kit is not installed:
-
Buy the kit (Part# 24793-1) and AERtrim feature (Part# not released).
-
Install the hardware and go to step 4 after completing this step.
-
To activate the AERtrim feature, provide the required unit information from the “AERtrim Activation” screen to AERCO Customer Service:
- Unit Serial #
- Fixed ID
- AERtrim ID
(Advanced Setup > Performance > AERtrim > AERtrim Settings > AERtrim
Activation)
Note: Power cycling the unit generates a new AERtrim ID and a new
AERtrim Activation Code associated with it is required to activate the
feature. Follow steps 3 and 4 to get a new code.
- Get the AERtrim Activation Code associated with the above unit information from AERCO Customer Service. Enter this code on the activation screen and press enter. “AERtrim Status” on the screen changes to “Active” upon successful activation. Once AERtrim is activated, it will stay active even if the unit is power cycled or the firmware is updated.
Specifications
Feature | Details |
---|---|
O2 Sensor Offset | 2.1 |
Last Calibration Time | 1:20 AM |
Calibration Frequency | 07/24/2022 |
AERtrim Activation Details
Parameter | Value |
---|---|
O2 | 5.5 |
Unit Serial # | E-00-00245 |
Fixed ID | 740703 |
AERtrim ID | 6462 |
AERtrim Activation Code | Enter |
AERtrim Status | Inactive |
FAQ
- What should I do if my O2 Sensor field is blank?
- If the O2 Sensor field is blank, it indicates that the O2 Monitoring Kit is not installed and you should proceed with step 2.
- Where can I find the AERtrim Activation screen?
- The AERtrim Activation screen can be found under Advanced Setup > Performance > AERtrim > AERtrim Settings > AERtrim Activation.
- Will AERtrim remain active after power cycling or firmware updates?
- Yes, once AERtrim is activated, it will stay active even if the unit is power cycled or the firmware is updated.
Using Instructions
To activate the AERtrim feature on the Edge Controller, follow the steps below:
-
Check if the 02 Monitoring Kit is installed on the unit.
If the “O2” field is blank, the kit is not installed.
If “O2” has values, skip step 2.
(Calibration > Input/Output > O2 Sensor) -
If the kit is not installed:
- Buy the kit (Part# 24793-1) and AERtrim feature (Part# not released).
- Install the hardware and go to step 4 after completing this step.
-
To activate the AERtrim feature, provide the required unit information from the “AERtrim Activation” screen to AERCO Customer Service:
- Unit Serial #
- Fixed ID
- AERtrim ID
(Advanced Setup > Performance > AERtrim > AERtrim Settings > AERtrim Activation)
Note: Power cycling the unit generates a new AERtrim ID and a new AERtrim Activation Code associated with it is required to activate the feature. Follow steps 3 and 4 to get a new code.
-
Get the AERtim Activation Code associated with the above unit information from AERCO Customer Service. Enter this code on the activation screen and press enter. “AERtrim Status” on the screen changes to “Active” upon successful activation.
Once AERtrim is activated, it will stay active even if the unit is power cycled or the firmware is updated.
CONTACT
AERCO International, Inc.
- 100 Oritani Drive
- Blauvelt, NY 10913
- USA: T: 845-580-8000
- Toll Free: 800-526-0288
- AERCO.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>