vtech VM5255 Video Baby Monitor User Guide

: June 1, 2024
: vtech

Table of Contents

VM5255 Video Baby Monitor
Product Information
Specifications:
- Product Usage Instructions
Safety Instructions:
Power Adapter Information:
- FAQ
Question: How can I register my product for warranty
Question: What should I do if I encounter privacy loss

VM5255 Video Baby Monitor

“`html

Product Information

Specifications:

Frequency control: Crystal controlled PLL synthesizer
Transmit frequency: Baby unit – 2405 – 2475 MHz, Parent unit –
2405 – 2475 MHz
Channels: 32
Display: 5″ Color LCD (WQVGA 480×272 pixel)
Nominal effective range: Actual range may vary based on
environmental conditions
Power requirements:
- Parent unit: 3.8V Li-ion battery
- Baby unit power adapter output: 5V DC @ 1000mA
- Parent unit power adapter output: 5V DC @ 1A

Product Usage Instructions

Safety Instructions:

Ensure adult setup is required.
Do not install the baby unit above 6.5 feet (2 meters).
Avoid placing the product close to heating sources.
Regularly inspect all components for damage.
Test sound reception each time you turn on or move the
units.
Avoid disassembling the product; take it to an authorized
service facility if needed.
Keep cords out of reach of children to prevent strangulation
hazards.

Power Adapter Information:

Parent unit output: 5V DC 1A – Model: VT05EUS05100
Baby unit output: 5V DC 1000mA – Model: VT05EUS05100

FAQ

Question: How can I register my product for warranty

support?

Answer: You can register your product for enhanced warranty
support and receive the latest VTech product news by visiting
www.vtechphones.com.

Question: What should I do if I encounter privacy loss

concerns?

Answer: To minimize privacy risks, avoid placing the product in
direct sunlight and keep it away from heating sources.
Additionally, periodically check all components for any signs of
damage.

“`

Crystal controlled PLL synthesizer
Baby unit: 2405 – 2475 MHz Parent unit: 2405 – 2475 MHz
32
5″ Color LCD (WQVGA 480×272 pixel) Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Parent unit: 3.8V Li-ion battery Baby unit power adapter: Output: 5V DC @ 1000mA Parent unit power adapter: Output: 5V DC @ 1A

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product. Company: VTech Communications, Inc. Address: 9020 SW Washington Square Road – Ste 555 Tigard, OR 97223, United States Phone: 1 800-595-9511 in the U.S. or 1 800-267-7377 in Canada

Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news.
Quick start guide

Credits: The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.

Frequency control Transmit frequency Channels LCD Nominal effective range Power requirements

VM5255 VM5255-2 Remote Pan and Manual Tilt
Video Baby Monitor

For more support information:

S m

VM5255

VM5255-2

Important safety instructions

The applied nameplate is located at the bottom of the baby unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above 6.5
feet (2 meters). 4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be used as such. 5. This product is not intended for use as a medical monitor. 6. Do not use this product near water, for example, near to a bath, sink, swimming pool or shower. 7. CAUTION: Use only the battery provided (if applicable). There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery in fire or a hot oven, mechanically crushing or cutting the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 8. Use only the power adapters included with this product. Incorrect power adapter polarity or voltage can seriously damage the product.
Power adapter information: Parent unit output: 5V DC 1A VTech Telecommunications Ltd. Model: VT05EUS05100 Baby unit output: 5V DC 1000mA. VTech Telecommunications Ltd. Model: VT05EUS05100
Rechargeable battery information: Li-ion battery, 3.8V 2100mAh Zhongshan Tianmao Battery Co., Ltd. Model Number: BP1763 9. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 10. For pluggable equipment, the socket-outlet (power adapter) should be installed near the equipment and should be easily accessible. 11. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 12. Do not modify the power adapters or replace with other adapters, as this causes a hazardous situation. 13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or electricity supply provider.
Do not overload wall outlets or use an extension cord. 16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat source. 18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Disassembling or removing parts of the product other than via the battery door (if applicable) may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
20. You should test the sound reception every time you turn on the units or move one of the components.
21. Periodically examine all components for damage. 22. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you are not intending to use it for some time. 23. Children should be supervised to ensure that they do not play with the product. 24. The small parts of this monitor can be swallowed by babies or small children. Keep these parts out of reach of children. 25. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS
Cautions · Use and store the product at a temperature between 32oF
(0oC) and 104oF (40oC). · Mishandling batteries can cause burn, fire or explosion
hazards. · Batteries should not be exposed to excessive heat such as
bright sunshine or fire. · Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.

·

Warning–Strangulation Hazard–Chil-

dren have STRANGLED in cords. Keep this cord out of the reach of children (more than

3 ft (0.9m) away). Do not remove warning label on the adapter cord.

· Never place the camera unit(s) inside the baby’s crib or playpen. Never cover the camera unit(s) or parent unit with anything such as a towel or a blanket.

· Other electronic products may cause interference with your camera unit. Try installing your camera unit as far away from

these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions,

personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients · Should keep wireless devices at least six inches from the
pacemaker. · Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON. WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.

Strangulation Hazard
Keep this cord out of reach of children. The cord needs to be at least three feet away from the child at all times. Do not use with an extension cord. Do not remove this tag.
Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez pas de rallonge. Ne retirez pas cette étiquette.
Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños. Este cable debe estar por lo menos tres pies fuera de la alcance del niño en todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.
Strangulation Hazard
Keep this cord out of reach of children. The cord needs to be at least three feet away from the child at all times. Do not use with an extension cord. Do not remove this tag.
Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez pas de rallonge. Ne retirez pas cette étiquette.
Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños. Este cable debe estar por lo menos tres pies fuera de la alcance del niño en todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.

What’s in the box

Quick start guide

x 2

1 set for VM5255 2 sets for VM5255-2

1 Connect the baby monitor
NOTES
· The rechargeable battery in the parent unit is built-in. · Use only the power adapters supplied with this product. · Make sure the baby monitor is not connected to a switch-controlled electric outlet. · Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. · Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.

1 Connect the baby monitor (cont’d)

Charge the parent unit battery
When you have connected and turned on the parent unit, the battery will be charged automatically.
Notes
· Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon becomes solid .
· It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.
· The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.

The battery icon indicates the battery status (see the following table).

Battery indicators

Battery status

Action

The screen displays . The light flashes.
The battery icon becomes solid .

The battery has very little charge and may be used for only a short time. The battery is fully charged.

Charge without interruption (about 30 minutes). To keep the battery charged, connect it to AC power when in use.

2 Power on or off the baby monitor

Slide the ON/OFF switch to power on or off your baby unit.

Press and hold POWER to power on or off your parent unit.

Press and hold

3 Positioning the baby monitor

Caution
· Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s crib or playpen.

3ft (1m)

63

3ft (1m)

63

< 3ft (1m)

Caution
· The default volume of your parent unit is level 4, and the maximum volume is level 7. If you experience high-pitched screeching noise from your baby monitor while positioning: – Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR – Lower the volume of your parent unit.

3ft (1m)
63

Tip
· You can manually tilt the camera angle up and down by pushing the lens portion upwards or downwards.

< 3ft (1m)

Note
· To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers.

4 Status check
Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on. The ON LED light of baby unit turns on.

CONFORMS TO UL STD. 62368-1 CERTIFIED TO CSA STD. C22.2 NO.62368-1

Technical specifications

Basic operation – Parent unit

Adjust speaker volume
Press / to adjust your parent unit speaker volume.

Zoom
Press to zoom in or out.

26 26

Use the menu
Press to enter the menu, choose a menu item, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit’s lullaby, or to adjust the baby unit’s sound sensitivity.
While in the menu: 26
· Press or to scroll among the menu options. · Press to select an item, or to save a setting. · Press or to scroll among the sub-menus,
or to adjust a setting. · Press to return to the previous menu options without
changing the current setting. · Press /EXIT to return to live video.

Talk to your baby unit
Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when finish talking and hear your baby again.

Turn off the screen
Press and hold LCD ON/OFF to switch off the screen. You can still hear sound from the baby unit.

63

Press and hold

Press and hold
Tip
· Press any keys on the parent unit to turn on the screen again.

WARM

NOTE: Camera lens and surface may get warm during normal operation.

Overview – Parent unit

1 2
1 LED lights 2 LCD display 3 Microphone 4 POWER 5 TALK

11

3

4

12

5

6

7

14

8

13

9

10

6 MENU/SELECT

10

/EXIT

7 Arrow keys

11 Antenna

·

While viewing image from the camera unit, press and hold

12

RESET · Force reboot the

to pan the camera

parent unit.

unit leftward or rightward.

13 Stand

8

|

(Volume)

14 Power jack

9 VIEW /LCD ON/OFF

Overview – Baby unit

1

2

8

3

6

4

7

9

5

10

1 Light sensor 2 Camera 3 Gloss lens 4 Microphone 5 Night light 6 ON/OFF switch 7 POWER LED light
· On when the baby unit is turned on and is paired to the parent unit.
· Flashes when the baby unit is not being viewed; or when the link to the parent unit is lost.

11

13

12

8 Speaker

9

Night light

· Turn On/Off and switch between

seven colors of night light.

10 Power jack 11 Pair key

· Your parent unit and baby unit(s) provided are already paired.
12 Temperature sensor
13 Slots for wall mounting

Need help?

For operations and guides to help you use your video monitor, and for the latest information and support, check out our online help topics

S

and online FAQs.

m

Use your smartphone or mobile device to access our online help.

· Go to https://help.vtechphones.com/vm5255 or https://help.vtechphones.com/vm5255-2; OR
· Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the notification to be redirected to the online help page. – If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.
You can also call our Customer Support at 1 800-595-9511 [in US] or 1 800-267-7377 [in Canada] for help.

VM5255 VM5255-2

Parent unit icons

Main menu icons
Main Sub-menu menu Brightness
· Adjust the parent unit’s LCD brightness.

Camera settings
Lullaby /

Baby unit speaker volume · Adjust the baby unit’s speaker
volume. Monitoring mode (For VM5255-2 only)
· Single mode · Split mode
· Patrol mode
Play/Stop lullaby

· Select one of the soothing sounds, or white noise.

· Select one of the five melodies. · Play all melodies. · Set timer to stop playing the selected
melody or soothing sound.

Main Sub-menu menu

Night light

/

Turn on/off night light

4 5 6 7
· Select one of the night light colors.

· Change to all seven colors in cycles.

Main Sub-menu menu
Temperature
/ · Turn on/off temperature alert tone. · Set the parent unit to beep whenever the
room temperature detected by the baby unit falls outside of the set temperature range.
· Set the minimum temperature.

· Set timer to turn the night light off. · Select to set the night light to always on.

· Set the maximum temperature. · Set temperature display in Fahrenheit (oF)
or Celsius (oC).

A
Alert tones

· Set to auto turn on the night light when baby unit detects sound. It will turn off after 15 minutes of no sound detection. You can set VOX sensitivity level to detect sounds that exceed certain levels. See Sound sensitivity and sound activation section. /
· Turn on/off the adaptive night light feature. When this feature is on, the baby unit detects the ambient light. If the room is bright, the night light adjusts itself to be brighter; if the room is dim, the night light adjusts itself to be dimmer.
· Set the parent unit to beep when the battery is low.
· Set the parent unit to beep when the link between the parent unit and the baby unit is lost.
· Set the confirmation tone on or off when selecting an option in the menus.
· Set the parent unit to beep when the baby unit detects sounds while in Split mode (For VM5255-2 only).

Sound activation – screen and audio

/

Turn on/off sound activation

· Set sound activation on or off. · When it is on, and the baby unit detects
no sound, the parent unit screen stays off to save power. Once a sound is detected, the parent unit screen and speaker turns on automatically, and you can see and hear your baby. The parent unit will then turn off again after 50 seconds of no sound detection.

Note
· When the parent unit screen is off and it receives alerts, for example, link lost between parent unit and baby unit, or battery is low, the parent unit screen and speaker will turn on for 10 seconds.

VOX (Voice Activated Alert) Sensitivity
· You can set VOX sensitivity levels to activate parent unit screen and sound when baby unit detects sounds that exceed certain levels. See Sound sensitivity and sound activation section.

Parent unit icons (Cont’d)

Status icons

Connection status

·

– Strong signal strength.

· – Moderate signal strength.

· – Low signal strength.

· – Weak signal strength.

Split mode (*For VM5255-2 only)

Patrol mode (*For VM5255-2 only)

Current view status

or

· The baby unit number that is

being viewed when in:

– Single CAM mode. – Patrol mode
(For VM5255-2 only). – Split mode
(For VM5255-2 only).

Night vision – On

Zoom – On

Lullaby – On

Night light – On

Night light – Auto-on · Color icon indicates the night
light is set to auto-on, and is currently turned on by sound activation. · Gray icon indicates the night light is currently off but is set to auto-on. Night light will turn on when sound is detected by the baby unit.

Status icons

oF or oC

Real-time temperature · Real-time temperature
detected by the baby unit in Fahrenheit (oF) or Celsius (oC) (e.g. 57 oF or 14 oC).

Temperature alert tone – On

9-level sound indicator · indicates low sound level
detected by the baby unit.

·

indicates moderate

sound level detected by the

baby unit.

·

indicates high

sound level detected by the

baby unit.

Mute alert · Displays when the parent unit
speaker volume is set to off. · Displays when the parent unit
is talking to the baby unit.

Battery status

·

animates

when the battery is charging.

· – battery is fully charged.

· – battery is low and needs charging.

Alert icons
· Displays when parent unit’s battery is low and needs charging. · Displays when connection between parent unit and baby unit is lost. · Displays when sound is detected at a baby unit when in Split view (For
VM5255-2 only). · Baby unit detects temperature reaches or exceeds the set maximum. · Baby unit detects temperature is at or is lower than the set minimum.
CABLE MANAGEMENT

1

2

3

Mount the baby unit on dry wall (optional)

Notes
· Check for reception strength and camera angle before drilling the holes.
· The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the screws and anchors separately to mount your camera units.

1. Place the wall mount bracket on a wall and then use a pencil to mark two holes in parallel. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit).

2. If you drill the holes into a stud, go to step 3.
· If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall.

3. Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount bracket position is fixed. You can tighten the other screw in the top hole.

4. Place the camera unit on the wall mount bracket, and then slide it forward until it locks into place. Connect the power adapter to the camera unit and a power supply.

2 1

3. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed. Place the camera unit on the wall mount bracket, and then slide it forward until it locks into place.
OR
4. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place.

5. You can maximize your camera unit’s viewing angles by tilting the wall mount bracket. Hold the camera unit, and then rotate the knob in an anti- clockwise direction. This will loosen the joint of the wall mount bracket. Tilt your camera unit up or down to adjust to your preferred angle. Then, rotate the knob in a clockwise direction to tighten the joint and secure the angle.

Sound sensitivity and sound activation

Adjust sound detection sensitivity

You can turn on Sound activation and adjust the VOX sensitivity to detect sounds and turn on the parent unit while its screen is switched off or dimmed. When the baby unit detects sounds that exceed certain levels, the parent unit screen turns on, the baby unit starts transmitting sounds to the parent unit, and you can see and hear your baby. If you have turned on the Night light Auto-on feature, it will turn on automatically to sooth your baby. If you turn off Sound activation, you will hear sounds from the baby unit all the time, even when the parent unit screen is switched off. If you have turned on sound alert, the parent unit beeps when the baby unit detect sounds while in Split mode (*For VM5255-2 only).

VOX Sensitivity level
Description

Level 5 (Highest)

Level 4 (High)

(Default setting) The parent

The parent unit screen and speaker turn on for very small sounds, including background noises from your baby’s room.

unit screen and speaker turn on for soft babbling and louder sounds from your baby. The parent unit remains quiet when your

baby sleeps

soundly.

Level 3 (Medium)
The parent unit screen and speaker turns on for loud babbling and louder sounds from your baby. The parent unit remains quiet when your baby makes soft sounds.

Level 2 (Low)
The parent unit screen and speaker turn on for crying and louder sounds from your baby. The parent unit remains quiet when your baby makes soft sounds.

Level 1 (Lowest)
The parent unit screen and speaker turn on for loud crying or screeching sounds from your baby. The parent unit remains quiet when your baby makes soft sounds.

Sound activated screen and audio
When Sound activation is on, the parent unit screen stays off to save power when the baby unit detects no sound. Once the baby unit detects sounds that are louder than the chosen sound sensitivity level, the parent unit screen and speaker turn on automatically. The parent unit will then turn off again after 50 seconds of no sound detection.
Note
· If you have muted the parent unit speaker, only the parent unit screen will turn on when a sound is detected.

Night vision

The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The images from the baby unit are in black and white, and appears on the screen.
Notes
· It is normal to see a short white glare on your parent unit screen when the baby unit adapts to the dark environment.
· When the infrared LEDs are on, it is normal for the images to be in black and white.
Tip
· Depending on the surroundings and other interfering factors, for example, lighting, objects,colors and backgrounds, the image quality may vary. Adjust the baby unit angle or place the baby unit at a higher location to prevent glare and a blurred display.

Dim mode
The parent unit display will turn off to conserve energy after 10 minutes of inactivity, in which there is neither key pressed nor alert received from the baby unit.
10 min inactivity
Press any button

For VM5255-2 only

Status check – Two baby units

If you are viewing baby unit , the POWER LED light of baby unit
turns on. As baby unit is not being viewed, its POWER LED light flashes.

Note
· If you power on only one baby unit, you may see the parent unit displaying the LINK LED light flashing.

and then

· Press VIEW in Single CAM or Patrol mode to switch to the baby unit you have powered on.

, and

Change different views – Single CAM

In Single CAM or Patrol mode, press VIEW to switch
26
between the image of baby units and .
Press
Change different views – Patrol

26
Press VIEW
Change different views – Split

Select Patrol as your monitoring mode to alternately view the image from baby units
and every 10 seconds.

Select Split as your monitoring mode to view the images from both baby units at once.

26

10s

The RBRC seal
The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal waste, which may be illegal in your area. VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC seal and 1-800-8-BATTERY® are registered trademarks of Call2recycle, Inc.
FCC and IC regulations
FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B)
Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term ’IC:’ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
California Energy Commission battery charging testing mode
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy- conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.

For cETL compliance only

Mesures de sécurité importantes La plaque signalétique appliquée est située au bas du socle de l’unité du bébé. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie, d’électrocution et de blessures corporelles, dont ceux qui suivent : 1. Observez toutes les instructions et mises en garde inscrites
sur l’appareil. 2. L’installation par un adulte est requise. 3. MISE EN GARDE: N’installez pas l’unité du bébé à une
hauteur supérieure à 2 mètres. 4. Ce produit ne remplace pas la surveillance adulte du
nourrisson. La supervision du nourrisson est la responsabilité du parent ou de la personne qui s’occupe de l’enfant. Ce produit pourrait cesser de fonctionner et, par conséquent, vous ne devriez pas présumer qu’il continuera de fonctionner correctement pendant une période de temps donnée. De plus, il ne s’agit pas d’un instrument médical et ne devrait pas être utilisé comme tel. Ce produit est destiné à vous aider à superviser votre bébé. 5. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche. 6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque d’explosion si un autre type de batterie est utilisé pour l’unité Parents. N’incinérez pas les piles. Cellesci risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant le sceau du RBRC. 7. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque d’endommager sérieusement le produit et mettre votre sécurité en péril.
Informations sur les adaptateurs électriques : Adaptateur de l’unité du parent : Sortie : 5V DC 1A VTech Telecommunications Ltd. Modèle : VT05EUS05100 Adaptateur de l’unité du bébé : Sortie : 5V DC 1000mA VTech Telecommunications Ltd. Modèle : VT05EUS05100
Informations sur les piles rechargeables : Li-ion battery, 3.8V 2100mAh Zhongshan Tianmao Battery Co., Ltd. Model Number: BP1763 8. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché dans une prise au plafond, sous une table ou dans un meuble. 9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, afin d’assurer une accessibilité sécuritaire à la prise de courant. 10. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon humide pour le nettoyer. 11. Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car ceci peut présenter un danger potentiel. 12. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser le cordon d’alimentation ou de le piétiner. 13. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité. 14. Ne surchargez pas les prises de courant murales ni les rallonges électriques. 15. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants. 16. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer, ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.

17. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courtscircuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.
18. Afin de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.
19. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.
20. Examinez les composantes afin de vérifier si celles-ci ne sont pas endommagées.
21. Il existe un très faible risque de perte de confidentialité avec certains appareils électroniques (autres écoute-bébés, téléphones sans fils etc.). Pour l’éviter, s’assurer que le produit n’a jamais été utilisé avant l’achat, réinitialiser l’unité de façon périodique, éteindre l’écoute-bébé quand il n’est pas en cours d’utilisation.
22. Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.
23. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné suffisamment de supervision ou d’instructions relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité. CONSERVEZ CES INSTRUCTIONS
Mises en garde 1. Utilisez et entreposez le produit à une température entre
0° C (32°F) et 40°C (104° F). 2. N’exposez pas cet appareil à des froids ou des chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source de chauffage. 3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.

Avertissement – Risque de strangulation

– Les enfants se sont ÉTRANGLÉS dans des

cordons. Gardez ce cordon hors de portée

des enfants (à plus de 0,9 m). N’enlevez pas

cette étiquette.

5. Ne jamais placer le moniteur à l’intérieur du berceau

ou du parc de bébé. Ne jamais couvrir le moniteur ou

l’unité (s) portative avec un article tel une serviette ou une

couverture.

6. D’autres équipements électroniques peuvent produire des

interférences sur votre moniteur vidéo et audio. Tentez

d’installer votre moniteur vidéo ou audio à l’écart des

appareils électroniques tels que des routeurs sans fil, radios,

téléphones cellulaires, interphones, moniteurs, téléphones,

ordinateurs personnels, électroménagers et téléphones

sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans fil) :

L’organisme `Wireless Technology Research, LLC (WTR)’, une

firme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans

fil portatifs et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la firme WTR recommande aux

médecins:

Avis aux détenteurs de stimulateurs cardiaques

· Vous devriez maintenir les dispositifs sans fil à au moins six

pouces du simulateur cardiaque.

· Ils ne doivent PAS placer le téléphone sans fil directement

sur le stimulateur cardiaque, tel que dans une poche de

chemise, lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de

risque pour les détenteurs de simulateurs cardiaques causés par

les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF) Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.

Limited warranty
What does this limited warranty cover? The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)? During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period? The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty? This limited warranty does not cover: 1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or 2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or 3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or 4. Product to the extent that the problem is caused by use with non-VTech accessories; or 5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or 6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or 7. Product returned without a valid proof of purchase (see item 2 below); or 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service? To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 800-595-9511. In Canada, go to www.vtechcanada.com or call 1 800-267-7377. NOTE: Before calling for service, please review the user’s manual – a check of the Product’s controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service? 1. Return the entire original package and contents including
the Product to the VTech service location along with a description of the malfunction or difficulty; and 2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and 3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/ provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.