SonoFF ZBMINIL2-V1.1 Zigbee Smart Switch User Manual

ZBMINI Extreme
User manual V1 .1 Zigbee Smart Switch
(No Neutral Required)

Product introduction

The device weight is less than 1 kg, and the recommended installation height is less than 2m.

LED indicator status instruction

Green LED indicator keeps on
(Relay is powered on)| Device is on line
Green LED indicator quick flashes
(Relay is powered on)| Abnormal network connection
ZBMINI Extreme and router connect normally, but router
and the hub are disconnected
Green LED indicator slow flashes
(Relay is powered on)| Abnormal network connection
Slow flashing under non-pairing state: ZBMINI Extreme and the parent device are disconnected

Features

SONOFF Zigbee smart switch (No neutral required) allows you to remote control, schedule on/off and set smart scenes to trigger other devices, etc. by connecting Zigbee hub.

Above functions are determined by the connected Zigbee Hub.

Installation

1. Power off
    Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector whilethe device is powered on!

2. Wiring instruction
   To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current operated Cicuit-breaker with Integral Overcurrent protection(RCBO) with an electrical rating of 6A has been installed before the ZBMINIL2.
   

For the above 3 4 wiring methods, please ensure the proper wiring and powering of the Lin terminal, otherwise it will cause the device to work abnormally.
Supported switches are rocker switch and push button and factory default by supporting rocker switch.
Unsupported to use with other Inductive loads such as fan.
Make sure all wires are connected correctly.

Pair with eWelink App

1. Download the eWelink App

2. Pair SONOFF Zigbee Bridge to your eWelink account

3. Power on
   After powering on, the device will enter the pairing mode defaulted during the first use and the green LED indicator will”flash slowly”.
   The device will exit the pairing mode if you do not operate it within 3mins. If you want to enter the pairing mode again, press and hold the button of the device for 5 seconds until the green Led indicator “flashes slowly” and releases.
   The device will remain off and cannot be controlled by the device’s button or external switch when it is in pairing mode.

4. Add ZBMINI Extreme to the ZB Bridge Open eWelink App, tap “Add” icon on the ZB Bridge interface, then wait to looking for and add the sub-devices.

Pair with Amazon Echo

1. Download the latest Amazon Alexa App and pair it with Amazon Echo with built-in Zigbee hub.

2. Power on ZBMINI Extreme, then it defaulted to enter the pairing mode and the green LED indicator “flashes slowly”.
   The device will remain off and cannot be controlled by the device’s button or external switch when it is in pairing mode.

3. Ask the Alexa Echo to discover the devices automatically by saying”Alexa, discover my devices”.
   If failed to pair within 3mins, ZBMINI Extreme will exit the pairing mode. Long press the button on ZBMINI Extreme for 5s to make it enter the pairing mode if you need to pair again.

Switch the device to the corresponding switch

The device supports rocker switch by default. If you want to change the switch type, press the button 3 times and see the green Led indicator flash 3 times quickly, then the switch type is switched successfully.
Please switch to the corresponding switch type before installing the device in the mounting box.

Install the ZBMINI Extrene in the mounting box

Specifications

LED: 150W Max @100V, 300W Max @240V
Wireless connection| Zigbee 3.0
Working temperature| -10–40°C
Casing material| PC VO
Product Size| 39.5x32x18.4mm

Factory reset

Return the device to its factory settings in any following ways (Device will enter the pairing mode automatically after resetting)

1. Press 1 O consecutive times the connected external switch
2. Long-press the device for 5s.
3. Delete the sub-device on eWelink App

Supported voice assistant

FCC compliance statement

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause  undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that  interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference  by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003(B).
This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

For CE Frequency

Operation frequency Range
Zig bee: 2405-2480M Hz
RF output Power
Zigbee: <13dBm

SAR Warning
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your  waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities.
Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection  points.

EU Declaration of Conformity
Hereby, Shenzhen Son off Technologies Co., Ltd. declares that the radio equipment type ZBMINIL2 is in compliance with Directive 2014/53/EU.The full text of the EU  declaration of conformity is available at the following internet address:
https://sonoff.tech/compliance/

Shenzhen Sonoff Technologies Co., Ltd.
3F &6F, Bid A, No. 663, Bu long Rd, Shenzhen, GD, China
ZIP code: 518000
Website: sonoff.tech
Service email: support@itead.cc
MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>