Dorman CM39896 Clutch Master Cylinder Instructions
- June 1, 2024
- DORMAN
Table of Contents
Dorman CM39896 Clutch Master Cylinder
Product Information
- Specifications:
- Product Name: Clutch Master Cylinder
- Vehicle Compatibility: Ford Ranger/Explorer
- Fluid Type: DOT 3 or 4 Brake Fluid
Product Usage Instructions
- Preparation and Removal:
- Carefully clean off the hydraulic tube coupling.
- Disconnect the coupling at the transmission using a hydraulic line Quick Disconnect (QD) tool.
- Remove the clutch master cylinder from the firewall after disconnecting the pedal linkage.
- Transfer and Replacement:
- Transfer or replace the reservoir, clutch pedal position switch, and clutch tube to the new master cylinder.
- Allow old fluid to drain into a waste container.
- Reservoir Setup:
- Support the reservoir in an appropriate fixture, ensuring the master cylinder and tube hang down from the reservoir as illustrated.
- Fill the reservoir with approved DOT 3 or 4 brake fluid.
- Bleeding Process:
- Depress the small valve in the middle of the QD coupling at the end of the clutch tube.
- Keep the end of the tube and coupling pointed down into a waste container to allow fluid to escape.
- Fully depress and hold the master cylinder push rod while maintaining fluid level in the reservoir.
- Repeat the bleeding process until the push rod can only be pushed in 4mm or less.
- Final Steps:
- Top off the reservoir with fluid.
- Check and replace the O Ring on the outside of the coupling if necessary.
- Reinstall the reservoir, clutch master cylinder, and clutch tube as one unit on the vehicle.
- Follow specific bleeding instructions for concentric slave cylinders.
FAQs
- Q: What type of brake fluid should I use with the clutch master cylinder?
- A: Use approved DOT 3 or 4 brake fluid with the clutch master cylinder.
- Q: What should I do if air is re-introduced into the system?
- A: If air is re-introduced, the master cylinder assembly will need to be removed and steps 3 through 12 repeated.
Cylinder Installation
Ford Ranger/Explorer Clutch Master Cylinder Installation
IMPORTANT: The Clutch Master Cylinder (M/C) on your vehicle is mounted at an angle on the firewall and bleeding MUST be done before installation!
Consult the vehicle service manual for further details.
- Carefully clean off the hydraulic tube coupling. Disconnect the coupling at the transmission with a hydraulic line Quick Disconnect (QD) tool by sliding the white plastic sleeve toward the slave cylinder.
- Remove the clutch M/C from the firewall after disconnecting the pedal linkage (1995/up – rotate cylinder 45 degrees clockwise). Remove the reservoir and clutch tube. Transfer or replace the reservoir, clutch pedal position switch, and clutch tube to the new M/C, allowing old fluid to drain into a waste container.
- Support the reservoir in an appropriate fixture or tool such as a vice, allowing the M/C and tube to hang down from the reservoir in the position illustrated below (push rod facing down and M/C angled up toward the reservoir). Care must be taken not to damage the reservoir.
- Fill the reservoir with an approved DOT 3 or 4 brake fluid. With a blunt tool, depress the small valve in the middle of the QD coupling located at the end of the clutch tube. Keep the end of the tube and coupling pointed down into a waste container, allowing fluid to escape from the QD valve.
- With the QD valve depressed, fully depress and hold the M/C push rod. Remove the tool allow the QD valve to close, and then slowly release the push rod. Maintain fluid level in the reservoir at all times to prevent air from being introduced.
- Repeat Step (5) four more times.
- With the QD valve closed, slowly depress the push rod using ¾” – 1” strokes. Observe the reservoir for air bubbles. Repeat this until the push rod can only be pushed in 4mm or less.
- Top off the reservoir with fluid. Replace the diaphragm and cap onto the reservoir.
- Check to be sure the “O” Ring on the outside of the coupling is present, clean and undamaged. Replace if necessary and lubricate with DOT 3 or 4 brake fluid.
- Reinstall the reservoir, clutch M/C and clutch tube as one unit on the vehicle. (1995/up – rotate M/C counterclockwise 45 degrees to install onto the firewall.)
- Reconnect the clutch tube by inserting QD coupling onto the coupling of the concentric slave cylinder. Make sure the line is secure.
- Follow steps 13 – 16 from the enclosed instructions for bleeding concentric slave cylinders.
- If air is re-introduced into the system, the M/C assembly (complete with reservoir and clutch tube) will need to be removed again, repeating steps 3 through 12. Air cannot be purged from the M/C while mounted on the firewall.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>