BIOWAVE BioWraps Compression Electrode Garment User Guide

Table of Contents

BIOWAVE-BioWraps-Compression-Electrode-Garment-product

Product Specifications

Product Name: BACK BIOWRAP SILVER Compression Electrode Garment
Technology: Advanced Silver Fabric Electrode Technology
Compatibility: ONLY for use with BioWaveHOME & BioWavePRO
Sizes Available:
- S / M: Waist Size 28 – 38
- L / XL: Waist Size 39 – 50*
- 51-60 require a Back Extender

Clean your skin with soap and water in the areas that will touch the silver fabric.
Apply a pea-sized amount of conductive Theracream on your skin where the silver fabric electrodes will touch.
Attach the 4 Snap Cables to the snaps on the outside of the BioWrap.
Connect the blue connectors at the other end of each cable to your BioWave Leadwire Cable.
Put on the BioWrap, ensuring strong but comfortable compression over the silver fabric locations.
Connect the leadwire cable to the BioWave device and turn it on by pressing the power button.
Adjust intensity using the PLUS (+) button for a strong but comfortable sensation.
After a 30-minute treatment, disconnect the cables, remove the BioWrap, and store it in a cool dry place.

Q: My BioWave shows a connection error but my BioWrap is plugged in. What should I do?

If your BioWave device displays a connection error when you are fully connected to the BioWrap, follow these steps.

Ensure that there is no excessive hair in the areas where the silver fabric electrodes touch your skin.
Verify that the silver fabric rectangles are properly aligned over the painful areas on your lower back.
Check if the secondary straps on the front of the BioWrap are securely tightened for proper compression.

Inside View

Outside View

The 4” Snap Cables should already be snapped onto each of the 2 snaps on the outside of the BioWrap.
Plug the blue connectors at the other end of each BioWrap cable into your BioWave Leadwire Cable.
Clean your skin with soap and water using a washcloth in the locations where the silver fabric will touch your skin.
Squeeze a separate pea-sized amount of conductive Theracream onto your fingertip and rub it into your skin thoroughly over the entire area so that the silver fabric electrodes will touch your skin.
- Use a pea-sized amount of cream for each silver fabric electrode.
See the diagrams on the opposite side to put on the BioWrap and velcro it closed firmly so there is strong but comfortable compression over the silver fabric locations.
Plug the single end of the leadwire cable into the BioWave device.
Press the power button to turn on the BioWave device.
Start the treatment by pressing the PLUS (+) button to increase intensity so the sensation felt is strong but still comfortable. As your body adapts to the electrical field and the sensation fades, keep pressing the PLUS
(+) button to increase the intensity to maintain a strong but comfortable sensation at the treatment location.
When the 30-minute treatment is over, disconnect the BioWave Leadwire cable from the 4” BioWrap cables, remove the BioWrap from your body, and store it in a cool dry place.

BIOWAVE-BioWraps-Compression-Electrode-Garment-fig-3

Squeeze a pea-sized amount of BioWrap CONDUCTIVE CREAM onto your fingertip and rub it into your skin thoroughly in the two locations that the silver fabric will touch.
Both 4” Sanp Cables should already be snapped onto the 2 snaps on the back side of the BioWrap. Attach your BioWave LEADWIRE CABLE to the two connectors on the back of the BioWrap
- Line up SILVER FABRIC RECTANGLES on the inside of BioWrap over painful areas on your lower back.
Wrap LEFT SIDE around the stomach.
- Wrap the RIGHT SIDE around the stomach, pull tight, and attach Velcro closure over the left side.
Unhook SECONDARY STRAPS on front of BioWrap.
PULL FORWARD and VELCRO DOWN on front of BioWrap to further tighten BioWrap over your low back.
- BioWrap should provide TIGHT BUT COMFORTABLE compression across your lower back.

My BioWave shows a connection error but my BioWrap is plugged in

If your BioWave device shows a connection error when you are fully connected to the BioWrap, remove the BioWrap and follow these steps:
If you forgot to apply Conductive Cream:
CLEAN YOUR SKIN. Remove BioWrap and clean your skin with soap and water in the region where the silver fabric electrodes touch your skin.
Shave any excessive hair in the locations where the silver fabric electrodes touch your skin.
APPLY A PEA-SIZE AMOUNT OF CONDUCTIVE CREAM directly to skin areas that will be against each of the silver fabric electrodes inside the BioWrap.
Gently massage Conductive Cream into the skin allowing it to absorb, before putting on the BioWrap.

If you applied too much Conductive Cream (more than a pea-sized amount):

CLEAN YOUR SKIN. Remove the BioWrap and use a dry towel to remove all excess Conductive Cream from your skin and any excess cream from the silver fabric in the BioWrap. Next, reattach the BioWrap and begin the treatment.

The treatment doesn’t feel strong enough

If the intensity is turned up to the maximum setting and the treatment doesn’t feel strong under the electrodes, pause the treatment, remove the BioWrap, and apply more conductive cream to the skin in the areas where the silver fabric touches the skin.
Tighter Compression and/or More Conductive Cream = Stronger Treatment Sensation.
Looser Compression and/or Less Conductive Cream = Less Treatment Sensation.

IMPORTANT

Contraindications When Not to Use BioWrap

DO NOT use it if you have an implanted cardiac pacemaker.
DO NOT place the silver fabric electrodes in the BioWrap over open wounds, broken skin, rashy skin, or sensitive skin areas like sunburned skin.

NOTE:

BioWrap Wearables MAY BE PLACED over or in the proximity of implanted orthopedic hardware, including total joint replacements, anchors, plates, rods, screws, pins, and clips.
Any serious incident that has occurred concerning the device should be reported to the manufacturer and the competent authority of the Member State in which the user and/or patient is established.

DISCONNECT and REMOVE the two 4” SNAP CABLES before hand washing the BioWrap.
HAND WASH using mild soap and RINSE in cold water.
PAT DRY with a TOWEL, then let AIR DRY.
DO NOT wash in a washing machine.
DO NOT place it in a dryer.
Need help?
Contact us at 1-877-BIOWAVE
(1-877-246-9283) support@biowave.com
The information, including but not limited to text, graphics, images, and other material contained herein is for informational purposes only. Learn more at BioWave.com/terms-of-use
BioWave Corporation 8 Knight St., Suite 201 Norwalk, CT 06851
See video athttps://biowave.com/support-biowraps/
Questions? Call us!
1-877-BIOWAVE
(1-877-246-9283)
support@biowave.com

| BIOWAVE BioWraps Compression Electrode Garment [pdf] User Guide
BioWraps Compression Electrode Garment, BioWraps, Compression Electrode Garment, Electrode Garment, Garment
---|---