Hunter 13164 Carrington Isle 1 Light Mini Pendant Instruction Manual

Carrington Isle
For Models:
Para los Modelos:
Pour les Modéles:
13164

13164 Carrington Isle 1 Light Mini Pendant

1 Light Pendant
Fixture weight +2 Ibs:  2.201bs (1.00 kg)

Hardware Service Kit

Here are the tools you need to complete your installation:

|
---|---
Ladder| Screwdriver
|
Plier| Wire Strippers

INSTALLATION INSTRUCTIONS

• To avaid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
• The lghing e mus e gounded he ground wire for the installation site is not Fvesem, immediately STOP instalation and consult qualfied electrican.
• Al wmn% must be in accordance with national and local electrical codes ANSI/NFPA 70.
  If you ate unfamilar with wiring or in doubt, consulta qualified electrican.

READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning installation of the lighting fixture.

PREPARING FOR INSTALLATION

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the wall, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Then remove cap nuts  (G) from mounting screws (A). Place the mounting plate (B) over the junction box so that mounting screws (A) and nuts (C) extend out away from the wall. Depending on the placement of your junction box the position of mounting screws (A) may need to be  adjusted to allow the canopy to be flush with the ceiling. Adjust the position of mounting screws (A) so that mounting screws (A) can be exposed 5-6 mm after passing through the canopy (F) to properly fit the cap nuts. Mounting screws (A) can be adjusted by  loosening nuts (C) and loosening or tightening mounting screws (A). Once the ideal position of mounting screws (A) has been confirmed, tighten nuts (C) on mounting screws (A) on the front of the mounting plate to ensure that mounting screws (A) are secure.  Pull the house wires through the center of mounting plate (B). Secure mounting plate (B) to the junction box by tightening the screws (D).

CONNECTING THE WIRES

Slide cord (K) through cord grip (N) to adjust the wire to desirable length [set screw (M) may need to be loosened first]. Tighten the set screw (M) with the included screwdriver (L) to lock it tight. Adjust the placement of the strain relief (0) on the cord above the  canopy. Cut excess cord leaving at least 8 to 10 inches of wire in addition to the desired length. Remove the outer jacket of each cord (K) to expose individual wires (white, black, green). Strip half an inch of jacket away from the ends of each individual wire. Have  a helper support the SR; ) < o fixture’s weight while completing the wiring. Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (live); white to white (neutral); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (E) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.

FINISHING THE INSTALLATION

Raise canopy (F) to mounting plate (B) and position mounting screws (A) so that they protrude through the openings of canopy (F). Secure canopy (F) in place with cap nuts (H). Secure Shade (1) onto the socket (H) by screwing socket ring (J) tight. Install light  bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Turn on the power and test the fixture. Your installation is now complete.

CLEANING TIPS

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>