DORMAN 742-352 Power Window Motor Installation Guide

DORMAN 742-352 Power Window Motor

Product Information

Specifications

• Part Number: 742-352
• Product Name: Window Lift Motor
• Recommended Safety Gear: Safety Glasses

Frequently Asked Questions

• Q: Do I need a service manual to install the Window Lift Motor?
  • A: Yes, it is recommended to refer to the appropriate shop manual for specific service procedures. If you lack the necessary skills, it’s best to seek the help of a qualified technician.
• Q: What tools are required for installation?
  • A: The tools required for removal and installation of the window regulator and motor assembly are specified in the shop manual. Additionally, wearing safety glasses is essential during the process.

ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

General Tech Tips

• Use painter’s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue.
• A plastic pry tool is useful. It will not easily damage delicate trim like a screwdriver or metal pry bar.
• The replacement regulator should have a liberal amount of grease on slide area. If there is not much grease present, white lithium grease works well to lubricate the slide area.
• Aftermarket window tinting can cause the window to travel slower and put additional strain on the window regulator assembly.
• Window run channels should be cleaned and lubricated before installation of a new window regulator assembly. Silicone spray works well.

Tools Required

Tools required for removal and installation of window regulator and motor assembly:

• Silicone spray lubricant
• Panel retainer remover
• Pick
• Saddle cup assembly, tape or wedge to hold window in place
• Flat-blade screwdriver or plastic pry tool
• 10mm socket or driver
• Phillips screwdriver

PLEASE WEAR SAFETY
GLASSES!

Removal Instructions

NOTE

Vehicle used was a 741-768 Jeep Cherokee.

• STEP 1: Gain access to the window regulator assembly by removing the interior trim panel.
  • STEP 1a: Remove the screws attaching the interior door trim panel to the inner door.
  • STEP 1b: Separate the interior door panel fasteners from the interior door using a panel retainer remover.
• STEP 2: Lift the trim panel up and outward to separate the trim panel from the interior window belt seal.
• STEP 3: Move the door trim panel outward and disconnect the interior door handle-to-latch rod retaining clips.
• STEP 4: Disconnect the power door locks/power window/ power mirror wire harness connectors (if equipped).
• STEP 5: Remove the door panel from the door.
• STEP 6: Remove the vapor barrier.
  • NOTE: The vapor barrier is attached to the door panel using a Butyl adhesive (a black sticky adhesive that has the appearance of caulk).
  • STEP 6a: Disengage the clips attaching the wiring harness to the door inner panel.
  • STEP 6b: Grasp the upper and lower rearward corners of the vapor barrier and rapidly peel back the vapor barrier from the door inner panel.
  • STEP 6c: Separate the vapor barrier from the door inner panel.
• STEP 7: Using either painter’s tape, saddle cup assembly or a window glass wedge, disconnect the window glass from the window regulator assembly.
• STEP 8: Loosen the bolts attaching the regulator to the inner door panel.
• STEP 9: Lift the regulator upward to release it from the keyed hole slots and remove the regulator through the access hole in the door inner panel.
• STEP 10: Remove the three (3) window lift motor attaching screws.
  • STEP 10a: Lift the window lift motor in an upward motion to remove from the window regulator.

Installation Instructions

• STEP 1: Attach the window lift motor to the window regulator by aligning the three (3) attaching screws and the window lift motor gear to the window regulator.
• STEP 2: Insert the window regulator through the access hole.
  • STEP 2a: Position the regulator in the door and align the regulator in the keyed hole slots in the door interior panel.
  • STEP 2b: Attach the regulator to the door interior panel with the attachment bolts.
• STEP 3: Attach the window glass to the window regulator.
• STEP 4: Re-attach the vapor barrier to the door interior panel.
  • STEP 4a: Attach the wiring harness to the interior door panel.
• STEP 5: Connect the harness connector to the power window/door lock/power mirror switch (if so equipped).
• STEP 6: Attach the door handle-to-door latch connecting rods.
• STEP 7: Verify that the new regulator is in operating order, there is no binding and that the glass operates properly in the UP and DOWN positions.
• STEP 8: In a downward motion, insert the door trim panel onto the inner window belt seal.
• STEP 9: Align door trim panel fasteners into the holes on the door.
• STEP 10: With equal and fi rm pressure, push the door panel onto the door.
• STEP 11: Re-install the screws into the corresponding holes in the interior trim panel. Be sure that the screws are aligned properly so that you do not cross thread the door.

We appreciate your opinions regarding this product!

Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product.
1-800-523-2492

Disclaimer

Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature.

©2011 Dorman Products, Inc.
No reproductions in whole or in part without prior written approval.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>