Durent Lighting Modern Bathroom Light Fixtures Instruction Manual

Durent Lighting Modern Bathroom Light Fixtures

Product Information

Specifications:

• Voltage: 120V
• Maximum Wattage: 40W per bulb

Product Usage Instructions

Tools Required (Not Included):
Before starting assembly and installation, please prepare the needed tools as below:

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Backplate (1)
• (F) Knob nut (2)
• (G) Arm (1)
• (H) Shade holder (3)
• (I) Screw (9)
• (J) Glass shade (3)

Assembly & Installation Instructions:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.
2. Turn off the power before starting the installation.
3. Secure mounting plate (D) to the outlet box with mounting screws (A).
4. Connect wires according to the provided chart. Ensure proper connection of ground wires.
5. Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Tuck all wires into the outlet box.
6. Attach back plate (E) to mounting plate (D) with knob nuts (F). Hand tighten until snug.
7. Install bulbs (Not included). Do not exceed the maximum wattage recommended on the socket.
8. Check that everything is installed properly before turning on the light.

Ordering Parts:
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Use exact wording from the illustration when ordering parts.

Frequently Asked Questions

Q: Can I use bulbs with a wattage higher than 40W per bulb?

A: No, it is recommended not to exceed the maximum wattage of 40W per bulb to ensure safety and proper functioning.

Q: What should I do if there are gaps between the mounting surface and the canopy?

A: Any gaps exceeding 3/16 should be corrected as required to ensure proper installation and stability of the lamp.

Q: How can I clean the lamp?

A: To clean the lamp, use a soft, dry cloth to gently wipe the surface. Avoid using acidic or alkaline substances that may damage the lamp's finish.

Safety Warning

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED NOT INCLUDED

Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

• (C) Green ground screw (1)

• (D) Mounting plate (1)

• (E) Backplate (1)

• (F) Knob nut (2)

• (G) Arm (1)

• (H) Shade holder (3)

• (I) Screw (9)

• (J) Glass shade (3)
  ACCESSORIES ENCLOSED:

• (A) Mounting screw (2)

• (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

3. Make Assembly

   • Step A1 » Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.

   • Step A2 » Carefully pass the supply wires from the outlet box through the mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).

   • Step A3 » Make wire connections
     Connect wires as below wires connection shown below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES. Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

   • Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
     NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (D) by unscrewing the pre-assembled hex nuts and then screwing the pre-assembled mounting screws in or out of mounting plate (D) until the secure length is achieved. Tighten the pre- assembled hex nuts and back to Step A4.

   • Step A5 »

   1. Secure glass shades (J) onto shade holders (H) with screws (I).
   2. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

4. Check everything is installed properly, then you can turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>