Durent Lighting B0921XRJQF 3 Light Drum Large Pendant Lighting Fixture with Fabric Shade Instruction Manual

Durent Lighting B0921XRJQF 3 Light Drum Large Pendant Lighting Fixture

with Fabric Shade

Product Information

Specifications

• Model: XYZ Chandelier
• Parts Included: Single bar, Green ground screw, Canopy, Collar ring, Collar loop, Quick link, Chain, Loop, Loop rod, Stem, Sockets assembly, Iron frame, Cloth lampshade
• Accessories Included: Wire connector, Mounting screw

Product Usage Instructions

Assembly & Installation

1. Preparation: Carefully remove all parts andaccessories from the packaging as illustrated.
2. Step A1: Attach loop rods to the iron frame and hang the other end on the bottom loop.
3. Step A2: Determine the correct number of links needed for hanging height and adjust the chain accordingly.
4. Step A3: Attach the quick link to the chain and loop.
5. Step A4: Weave the fixture wires through the chain and stop at the top, ensuring wires are not stressed.
6. Power Off: Turn off the power before installation by switching off the main fuse or circuit breaker and wall switch.
7. Step B1: Attach the single bar to the outlet box using mounting screws.
8. Step B2: Position the canopy over the collar loop and secure in place with collar ring.
9. Step B3: Pass the chain through the collar ring and canopy.
10. Step B4: Attach the quick link to the collar loop and pass fixture wires through to the top.
11. Step B5: Shorten fixture wires if needed, leaving at least 6 inches above the single bar.
12. Step B6: Make wire connections as shown in the wire connection diagram, ensuring proper grounding.

Frequently Asked Questions (FAQ)

• Q: Can I install this product without professional help?
  A: While it is possible to install the product following the provided instructions, it is recommended to seek installation by a licensed electrician for safety and compliance.

• Q: How do I adjust the hanging height of the chandelier?
  A: The hanging height can be adjusted by adding or removing links from the chain using chain pliers as described in Step A2 of the installation instructions.

WARNING (To reduce the risk of fire, electric shock, or personal injury):
IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED

(NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (C) Single bar (1)

• (D) Green ground screw (1)

• (E) Canopy (1)

• (F) Collar ring (1)

• (G) Collar loop (1)

• (H) Quick link (2)

• (I) Chain (1)

• (J) Loop (1)

• (K) Loop rod (3)

• (L) Stem (1)

• (M) Sockets assembly (1)

• (N) Iron frame (1)

• (O) Cloth lampshade (1)
  ACCESSORIES & QTY ENCLOSED:

• (A) Wire connector (3)

• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Make pre-installation

3. Step A1: Attach loop rods (K) to iron frame (N) and hang the other end of loop rods (K) on the bottom of loop (J).

4. Step A2: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.

5. Step A3: Attach quick link (H) to chain (I) and loop (J).

6. Step A4: Carefully weave the fixture wires through chain (I) in and out of every other link and stop just when you reach the top of chain (I). Gently pull the wires to ensure the wires are not stressed.

7. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

8. Make installation

9. Step B1: Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B).
   Note : the side of single bar (C) marked “GND” must face out.

10. Step B2: Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position.NOTE: canopy (E) should be snug against the ceiling and collar loop (G) should be screwed enough threads (no less than 6 threads) on the pre- assembled threaded nipple for more secure hanging. If not, adjust collar loop (G) on single bar assembly (C) by screwing collar loop (G) in or out of single bar (C) until the secure length is achieved.

11. Step B3: Pass chain (I) through collar ring (F) and then through canopy (E).

12. Step B4: Open quick link (H), attach quick link (H) to collar loop (G). Close quick link (H).
    Pass the fixture wires through collar loop (G) to the top of the pre­assembled threaded nipple and gently pull to ensure the wires are not stressed.

13. Step B5: If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above single bar (C) is at least 6″.

14. Step B6: Make wire connections
    Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
    Connect ground wires according to the below chart  Connect wires according to the below chart Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

15. Step B7: Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).

16. Step B8: Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

17. Check everything is already installed properly, then you could turn on the light. Enjoy!
    

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>