Durent Lighting B097DHJZ9X Modern Semi Flush Mount Ceiling Light Installation Guide
- June 16, 2024
- Durent Lighting
Table of Contents
Durent Lighting B097DHJZ9X Modern Semi Flush Mount Ceiling Light
Product Information
This product is a lighting fixture designed for installation in residential or commercial buildings. It is intended to provide illumination in indoor spaces. The fixture comes with all the necessary parts and accessories for assembly and installation.
Specifications
- Parts Included: Round mounting plate, Green ground screw, Canopy, Knob nut (2), Stem, Fixture body, Washer, Glass shade, Screw (3), Plastic washers (3), Tube ferrule, Flat cover, Column nut
- Accessories Included: Plastic wire connector (3), Mounting screw (2)
Product Usage Instructions
Safety Precautions
Before starting the installation process, it is important to follow these
safety precautions:
- It is recommended to have the fixture installed by a licensed electrician to reduce the risk of fire, electric shock, or injury to persons.
- Read the instruction manual carefully and keep it for future reference.
- Always shut off the electricity before attempting any work on the fixture.
Tools Required
Before starting the assembly and installation process, make sure you have
the following tools:
Assembly and Installation
- Carefully remove the fixture from the packaging and check that all parts and accessories are included as shown in the illustration.
- Turn off the power:
- Go to the main fuse or circuit breaker box in your home and place the main power switch in the OFF position.
- Place the wall switch in the OFF position.
- Unscrew the knob nuts from the mounting plate.
- Slip the stem over the wires and then thread it into the top of the canopy.
- Slip the fixture body over the wires and then thread it onto the top of the stem.
- Attach the mounting plate to the outlet box with the mounting screws.
- Make wire connections:
- Refer to the provided chart to connect the wires correctly.
- Twist the plastic wire connectors until the wires are tightly joined together.
- Carefully stuff all wires into the outlet box.
- Raise the canopy to the ceiling and secure it in place by tightening the knobs onto the threaded nipple on the mounting plate.
- Install the bulb (not included) according to the recommended maximum capacity on the socket.
- Pass the washer through the end of the stem and fix the glass shade to the stem with the column nut and flat cover.
FAQ
-
Q: Do I need a licensed electrician to install this fixture?
A: It is suggested to have the fixture installed by a licensed electrician to ensure safety and proper installation. -
Q: Can I exceed the maximum recommended bulb capacity?
A: No, it is important not to exceed the maximum capacity recommended on the socket to prevent damage or hazards.
Safety Precautions
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED
Before doing assembly and installation please prepare the needed tools as
below picture
PARTS TYPE & QTY INCLUDING
- (B) Round mounting plate (1)
- (C) Green ground screw (1)
- (E) Canopy (1)
- (F) Knob nut (2)
- (G) Stem (1)
- (H) Fixture body (1)
- (I) Washer (1)
- (J) Glass shade (1)
- (K) Screw (3)
- (L) Plastic washers (3)
- (M) Tube ferrule(1)
- (N) Flat cover (1)
- (O) Column nut (1)
ACCESSORIES & QTY ENCLOSED:
- (A) Plastic wire connector (3)
- (D) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration
-
Turn off power
Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the“OFF” position -
Unscrew the knob nuts(F) from mounting plate (B) .
-
Slip stem (G) over the wires and then thread it into the top of canopy (E). Slip fixture body (H) over wires and then thread it onto the top of stem (G).
-
Attach the mounting plate(B) to outlet box with the mounting screws(D).
-
Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF FIXTURE ,NEVER CONNECT
WIRES TO GROUND WIRES
Connect ground wire according to below chart Connect wires according to below chart
Twist
plastic wire connector(A) until wires are tightly joined together, then
carefully stuff all wires into the outlet box -
Raise canopy (E) to ceiling and secure canopy (E) in place by tightening knobs (F) onto the threaded nipple on mounting plate.
-
Install the bulb (not included) (Please do not exceed the maximum capacity recommended on the socket.)
-
Pass the washer (I) through the end of the stem (G) and fix the glass shade (J) to the stem (G) with the column nut (O) and flat cover (N).
-
Check everything is already installed properly, then you could turn on the light. Enjoy !
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>