AOH11F-AIM 11 Fin Oil Heater with Fan User Manual

: June 10, 2024
: AIM

AOH11F-AIM 11 Fin Oil Heater with Fan

AOH11F-AIM 11 Fin Oil Heater with Fan

USER INSTRUCTIONS

Please read this instruction manual carefully before using for the first time and always keep these instructions.

IMPORTANT SAFEGUARDS

When using the Oil Heater, basic safety precautions should always be followed including the following:

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
The product is for household use only.
Connect the appliance to single phase AC supply of the voltage specified on the rating plate.
In order to avoid overheating, do not cover the heater.
Never leave the heater unattended while it is in use. Always turn the product to the OFF position and unplug it from the electrical outlet when not in use.
Extreme caution is necessary when any heater is used by or near children, invalids or elderly people and whenever the heater is left operating and unattended.
The heater must not be located immediately below an electrical socket-outlet.
Do not run cord under carpeting and do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area and where it will not be tripped over.
Do not operate the heater with a damaged cord or plug, or after the heater malfunctions, has been dropped, or damaged in any manner.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person to avoid a hazard.
Avoid the use of an extension cord as this may overheat and cause a risk of fire.
Do not use on soft surfaces, like a bed, where openings may become blocked. Use the heater on flat, dry surfaces only.
Do not place this heater near flammable materials, surfaces or substances, as there may be a risk of fire. Keep the above flammable materials, surfaces or substances at least 1 m from the front of the product and keep them away from the sides and rear.
Do not use the heater in any areas where petrol, paint or other flammable liquids are stored e.g. Garages or workshops as a hot, arcing or sparking parts inside the heater.
Don’t use this heater in the immediate surroundings of a bath, a shower or a swimming pool. Never position the heater where it may fall into a bathtub or any body of water.
This heater is hot when in use. To avoid burns and personal injury, do not let bare skin touch hot surfaces. Use handles when moving the product.
Be sure that no other appliances are in use on the same electrical circuit, as an overload can occur.
This heater is filled with a precise quantity of special oil.
Repairs requiring opening of the oil container are only to be made by the manufacturer or the service agent who should be contacted if there is an oil leakage.
Regulations concerning the disposal of oil when discarding the appliance have to be followed.
The heater should not be used in a room, of which the floor area is less than 5 M2.
The cord shouldn’t be placed near the hot surface of the appliance.
Note: It is normal when the heaters are turned on for the first time or when they are turned on after having not been used for a long period of time may have noise inside, this will disappear when the heater has been on for a short while.

KNOW YOUR OIL HEATER

PRODUCT CHARACTERISTICS

Our electrothermal warmer operates as follows: the tubular element is taken as the heat source, efficient and permanent heat conduction oil is taken as the medium, heat eliminates via the radiation fin, room temperature is increased via air circulation.

Our electrothermal warmer has the following advantages: convenient, safe, beautiful, tranquil operation, without electromagnetic disturbance etc. It is suitable for such locations as scientific research room, hospital, hotel, training practice, house, and bedroom, etc. The warmer keeps your room or office more comfortable in cold seasons!

PRODUCT STRUCTURE DIAGRAM

Product Structure Diagram

ASSEMBLY INSTRUCTIONS

The heater is packaged with the feet unattached. You must attach them before operating the heater.

WARNING: DO NOT operate without feet attached. Only operate the heater in the upright position (feet on the bottom, controls on the top), any other position could create a hazardous situation.

MOUNTING

Take the heater and all the parts from the packing carton.

Stand the heater on its head.
Place the footplate on the top of both radiation fins.
Secure the footplate on the warmer with specified U type bolt and wing nuts.
Tighten the screw.
Turn the heater over so it stands on the wheels.
Once the wheels are assembled and the Heater is placed in the correct upright position, allow the oil to settle for a few minutes before switching the unit on. This will allow the oil to completely coat the heating element.

PLACING

The heater should be at least 90 cm away from walls or other objects such as furniture or curtains; ensure that the power supply corresponds to that on the nameplate; the temperature controller switch and power switch are at “OFF” position; plug in the attaching plug.

The temperature controller can regulate room temperature. Turn the temperature controller clockwise to increase the temperature; turn it anti-clockwise to reduce the temperature until appropriate temperature is reached.
Power switch is rotary switch: the switch gears are shown in the schematic diagram.
0 tap is the shutdown state.
I With power switch I pressed, the indicator “ON” indicates Level I power.
II With power switch II pressed, the indicator “ON” indicates Level II power.
III With both power switch I and II pressed, the indicator “ON” indicates Level III power.
IV With both power switch I and II pressed, the indicator “ON” indicates Level III power, PTC auxiliary heating at the same time open.
V With both power switch I and II closed, and only open the PTC auxiliary heating.
PTC auxiliary heating function, when the rotary switch to IV V, auxiliary heating starts, the fan and PTC begin to work. When the oil heater is heated to a certain temperature, the fan will switch on to strengthen the room cross-ventilation, this will keep uniform temperature distribution in the room.
To switch off the oil-heater, please press the power button to off Position, Turn the temperature Knob to the minimum position and take out the Plug.
Note: The heater operates via heat elimination, do not move the heater unless the oil has cooled down, only move the heater with the handle.

CLEANING

Please disconnect power supply before cleaning.
Wipe the outside of the heater with a wet cloth at first, and then dry it with a piece of soft cloth.
Do not use wax or brush polish, since these will react with the warmer, resulting in discoloration.

SAFETY PROTECTION

Do not cover the heater during operating, otherwise it could result in fire.
The heater should be 90 cm away from the wall or other flammable objects such as furniture, curtain, bed sheets or clothes.
Do not disassemble radiation fin.
Take care of your children when they are near or use the warmer.
Do not let the power cord contact damp or hot objects; do not wind or let children come near the power line.
Do not use the heater outside.
Do not let the heater come in contact with hot gasoline or electric burner.
Do not use damaged cable or plug; do not use damaged heater unless it is repaired.
Do not remove button parts of the heater.
This heater is only suitable for use indoors.

WARNINGS

Please read these instructions carefully before operating.
Please disconnect power supply when you are out or the heater is not being used for a long time.
Do not directly put clothes and other articles on the product to warm in case of fire.
Never put the heater just under the socket.
Never use the heater in locations with high air humidity such as bathroom, bath house or swimming pool etc.
The oil in this warmer is special heat conduction oil. Should it necessary to open oil tank during repair, only manufacturer or specified representatives are allowed to open the tank. In addition, please contact us immediately if there is oil leakage. Afterwards, the oil left on the surface should be removed.
The timer dial is only allowed to turn clockwise (slightly) as indicated by arrow, and turning it anti-clockwise will damage the timer.
If there is damage with the power cord, please contact manufacturer or service representatives immediately for replacing, otherwise it will be dangerous.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
The heat must not be located immediately below a socket-outlet.
Don’t use this heater in the immediate surroundings of bath, a shower or a swimming pool.
This heater is filled with a precise quantity of special oil. Repairs requiring opening of the oil container are only to be made by the manufacturer or his service agent who should be contacted if there is an oil leakage.
Regulations concerning the disposal of oil when scrapping the appliance have to be followed. WARNING: In order to avoid overheating do not cover the heater.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

CONFORMITY WITH DIRECTIVES

This product is CE marked to denote conformity with Directives 2006/95/EC (Low Voltage) and the EMC directive (2004/108/EC), as amended.

ENVIRONMENT FRIENDLY DISPOSAL

You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working electrical equipment to an appropriate waste disposal centre.

2 YEAR LIMITED WARRANTY

The Manufacturer hereby provides a warranty to the original purchaser of this product (‘the consumer’) that this product will be free of manufacturing defects in materials and workmanship which under normal, personal, family or household use (commercial use expressly excluded) manifest themselves within the 2 year from the date of purchase.

EXCLUSIONS

The warranty does not include and will not be construed to cover products damaged as a result of disaster, misuse, commercial use, not in accordance within the written instructions included with the product, abuse and/or any non-authorised modification of the product, incorrect installation of the product or normal wear and tear.
Insect infestation of the electrical or motor makes the claim invalid.

WAIVER

The warranty and the obligations of the Manufacturer provided herein are in lieu of, and the consumer, waives all other warranties, guarantees, conditions or liabilities, express or implied, arising by law or otherwise, including without limitation, any obligation of the manufacturer in respect of any injury, loss or damage (direct, indirect or consequential) arising out of the use of, or inability to use this product and whether or not occasioned by the manufacturer’s negligence or any act or omission on its part.

PROOF OF PURCHASE

Any claim in terms of the warranty must be supported by a proof of purchase. If such proof is not available, then not withstanding anything to the contrary herein, the service agent’s prevailing charges for services/repairs and/or spares will be payable by the Consumer upon collection of the repaired product. The Consumer should call the Pick n Pay CUSTOMER CARE number on 0860 30 30 30 (only in South Africa). Customers residing outside South Africa may return the product back to a Pick n Pay store. During the warranty period the product may only be serviced and/or repaired by the Manufacturer’s duly authorised agent(s).

Warranty If this product proves to be faulty during normal use due to defective materials or workmanship. Refer to our website for terms and conditions.

REPAIRS PROCEDURE

Should you experience any faults on your Aim product, please adhere to the following procedure to have the fault rectified speedily and professionally.
You can return the product to the store.
Call the Pick n Pay CUSTOMER CARE number on 0860 30 30 30 (only in South Africa) to report the fault and make arrangements for the next steps.

Note: Should you live in an outlying area or outside South Africa, it may be necessary to return the product to the store nearest to you.

COST OF REPAIRS

UNDER WARRANTY
Any items still under warranty will be repaired free of charge, as long as it complies with the terms and conditions of the warranty (refer to “warranties” section in this manual). Any items that need to be repaired that are NOT covered in the warranty will be for the consumer’s expense. A quote for the repair/replacement of these items will be provided to the consumer for approval prior to repairs being conducted.

OUT OF WARRANTY
Any items that need to be repaired once the warranty has expired will be for the consumer’s expense including call out fees. A quote for the repair/replacement of these items will be provided to the consumer for approval prior to repairs being conducted.

We are confident about the quality of our products. If you are not 100% satisfied with our product we will gladly exchange or give you your money back.

Specially packed for
Pick n Pay Retailers (Pty) Ltd.
Pick n Pay Office Park
2 Allum Road, Kensington, 2094
www.picknpay.co.za

Sharecall: 0860 30 30 30
ONLY IN SOUTH AFRICA
customercare@pnp.co.za
Product of China

AIM Logo