scheppach 7906100710 Pneumatic Tool Set Instruction Manual

scheppach 7906100710 Pneumatic Tool Set Instruction Manual

Pneumatic Tool Set

Translation of the original instructions

Explanation of the symbols on the equipment

Introduction

DEAR CUSTOMER,

We hope your new tool brings you much enjoyment and success.

NOTE:

According to the applicable product liability laws, the manufacturer of the device does not assume liability for damages to the product or damages caused by the product that occurs due to:

• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service technicians,
• Installation and replacement of non-original spare parts,
• Application other than specified,

Proper use

This tyre inflator gauge is intended for pumping up cycle tyres, inflatable boots, inflatable mattresses, balls etc. The blow gun is intended for cleaning and blowing out material from objects and difficult to access places. Any other use or modification to the device shall be considered as improper use and could give rise to considerable risk of accident. We will not accept liability for loss or damage arising from improper use. The device is intended for private domestic use only.

Features and equipment

1. Gauge
2. Tyre inflator gauge
3. Deflator valve
4. Plug-in nipple
5. Hose with valve connector, straight
6. rigger
7. Blow gun
8. Extension nozzle

Accessory:

9. Cap for (14), (15), (16)
10. Ball needle
11. Universal adapter
12. Universal adapter
13. Valve adapter, e.g. for cycle tyre valves
14. Universal adapter
15. Adapter for screw valves, e.g. on inflatable dinghies
16. Adapter for deflator valves

Included items

1 Tyre inflator gauge
1 Blow gun
2 Extension nozzles
1 Adapter set (8-piece)
1 Operating instructions

Technical data

Safety advice

Read all the safety advice and instructions. Failure to observe the safety advice and instructions could result in serious injury and / or damage to property.

Keep all the safety advice and instructions in a safe place for future reference!

• Check the air pressure with a suitable manometer after filling.
• RISK OF FIRE, EXPLOSION AND DAMAGE TO HEALTH! The device must be used in well-ventilated areas only.
• DANGER OF INJURY! Never exceed the maximum allowable working air pressure of 8 bar. Use a pressure reducer to set the working air pressure.
• RISK OF RECOIL FORCES! High working pressures can give rise to recoil forces that under certain conditions can result in danger from continuous loading.
• DANGER OF INJURY! IMPROPER USE! Never point the device at people or animals.
• DANGER OF INJURY! Never use oxygen or other combustible gas as the energy source.
• DANGER OF INJURY! First disconnect the hose from the compressed air source and only then disconnect the compressed air supply hose from the device. This will ensure that the compressed air supply hose does not wave around or recoil in an uncontrolled manner.
• For your own safety, wear suitable personal protective equipment.
• Keep children and other people away while you are operating the device. Distractions can cause you to lose control of the device.
• Disconnect the device from the compressed air source before carrying out any repairs or maintenance of the device or moving it to another location.
• When removing the hose coupling, hold the hose tightly in your hand to avoid injury caused by the hose shooting backwards.
• Look out for damage on the device. Check the device for damage before bringing it into use. Do not use the device if you discover any defects.
• Do not kink the device’s hose, otherwise you may damage it.
• NOTE! Observe the safety advice provided by the manufacturer of your inflatable article.
• Do not remove rating plates or labels – they are safety-relevant parts of the device.
• If you are inexperienced in the use of this type of device, you should seek out information or training to learn how to handle it safely.

Original accessories / attachments

• Use only the accessories and attachments detailed in the operating instructions. The use of accessories other than those recommended in the operating instructions could lead to you being in danger of injury.

Bringing into use

Connecting the compressed air source

NOTE : Operate the product only with cleaned, condensate- and oil-free compressed air and never exceed the maximum working air pressure at the device of 8 bar.

NOTE: The compressed air source must be fitted with a (filter) / pressure reducer so that the air pressure can be regulated.

• Connect the product to a suitable compressed air source by connecting the quick-release coupling of the air supply hose with the plug-in nipple (4) to the product. It locks itself in place automatically.

Using the tyre inflator gauge (2)

1. Place the valve connector (5) on to the valve

2. Press the trigger (6) to start the delivery of air.

3. Release the trigger (6) to stop the delivery of air.
   Read off the filling pressure on the gauge 1 .

4. If the object is overfilled with air (air pressure too high): Press the deflator valve (3) to release some air.

5. Press the lever of the valve connector (5) downwards and pull the valve connector (5) off the valve.

6. After you finish work, disconnect the device from the compressor.
   NOTE : First disconnect the hose from the compressor and only then disconnect the compressed air supply hose from the device. This will ensure that the compressed air supply hose does not wave around in an uncontrolled manner.

Using accessories:

• Press the lever of the valve connector (5) and insert the desired accessory (10) to (13) or the cap (9) into the valve connector (5)

Using the blow gun (7)

1. Screw an extension nozzle (8) on to the blow gun (7) .
2. Press the trigger (6) to start the delivery of air.
3. Release the trigger (6) to stop the delivery of air.
4. After you finish work, disconnect the device from the compressor.
   NOTE : First disconnect the hose from the compressor and only then disconnect the compressed air supply hose from the device. This will ensure that the compressed air supply hose does not wave around in an uncontrolled manner.

Maintenance and cleaning

• DANGER OF INJURY! Always disconnect the device from the compressed air source before you clean or maintain it.

The device requires no maintenance.

• Do not use sharp objects for cleaning the device.
  Do not allow any liquids to enter the device.
  Otherwise the device could be damaged.

• Clean the device frequently; for best results, do this immediately after you have finished using it.

• Clean the housing with a dry cloth.

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Defective components must be disposed of as special waste. Ask your dealer or your local council.

hereby declares the following conformity under the EU Directive and standards for the following article

www.scheppach.com

[email protected]

+(49)-08223-4002-99

+(49)-08223-4002-58

Warranty

Apparent defects must be notified within 8 days from the receipt of the goods. Otherwise, the buyerís rights of claim due to such defects are invalidated. We guarantee for our machines in case of proper treatment for the time of the statutory warranty period from delivery in such a way that we replace any machine part free of charge which provably becomes unusable due to faulty material or defects of fabrication within such period of time. With respect to parts not manufactured by us we only warrant insofar as we are entitled to warranty claims against the upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer. The cancellation of sale or the reduction of purchase price as well as any other claims for damages shall be excluded.

scheppach Fabrikation von Holzbearbeitungsmaschinen GmbH | Günzburger Str. 69 |
D-89335 Ichenhausen | www.scheppach.com

References

• scheppach | scheppach

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>