YOUKAIN YY68 Ceiling Fan with Light Instruction Manual

YOUKAIN YY68 Ceiling Fan with Light

Product Information

Specifications:

• Model No: YY68
• Remote control requires alkaline battery AAA 1.5Vx2pcs (not included)
• Can be connected to an on/off switch, not a dimmer switch

Product Usage Instructions

Assemble the Fan

1. Choose the appropriate size of Downrod (B) for installation.
2. Remove R pin (EE) and clevis pin (DD) from the downrod (B).
3. Assemble the canopy (A, C) and coupling cover (D), routing wires through the downrod (B).
4. Align the holes at the bottom of the downrod (B) with those in the motor and housing (E), then insert clevis pin (DD) and R pin (EE) to secure the downrod.
5. Fit the metal cover (D) onto the motor and housing (E).

Mount the Bracket

1. Attach the mounting bracket (AA) to the outlet box using screws provided.

Hang the Fan

1. Loosen canopy screws (JJ) from the mounting bracket (AA) and push canopy (A) up to the ceiling, then rotate to secure it.
2. Tighten the canopy screws (JJ) to secure the canopy (A) in place.
3. Install the decorative cover upwards.

Connect the Driver Wires

1. Connect the wires inside the fan to the driver (MM).
2. Connect the fixture wires to the house supply wires using wire nuts.
3. Place the driver (MM) in the mounting bracket (AA).

Important Notes:

• This fan only requires one set of input wires for control by remote.
• The fan can only be connected to an on/off switch, not a dimmer switch.

FAQ

Q: Can I use a dimmer switch with this fan?

A: No, this fan can only be connected to an on/off switch, not a dimmer switch.

Model No: YY68

PACKING LIST

INSTALLATION KIT

NOTE:

1. Parts “DD, EE” have already been installed with downrod assembly (B). They need to be disassembled before installation.
2. Canopy screws (JJ) have already been installed with mounting bracket (AA).
3. 2 pcs of set screw (FF) have already been installed with yoke (E).
4. Remote control requires alkaline battery AAA 1.5Vx2pcs (not included).

INSTALLATION

1. Assemble the Fan
2. Mount the Bracket.****
3. Hang the Fan.****
4. Connect the driver wires****
5. Fix the Canopy.****
6. Installing fan blades****
7. Assembling Lamp fixtures.****
8. Change the direction of the light source****

Balancing Kit

The balancing kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in your Owners Manual under “Attaching The Fan Blades.”

1. Turn the fan on and set the speed control setting to a speed at which the wobbles is the greatest.
2. Turn off the fan and allow it to a complete stop. Select one blade and place the balance clip (OO) on it, halfway between the blade holder and the blade tip on the trailing edge of blade.
3. Turn the fan on. Note whether the wobble has increased or decreased. Turn the fan off, move the clip to another blade, and retest. Repeat this procedure on all blades noting the blade on which the greatest improvement is achieved.
4. Move the clip back to the blade that showed the greatest improvement. Move the clip inward and outward on this blade and operate the fan to find the position where the clip gives the greatest improvement.
5. Remove the clip and install a balancing weight ( HH ) to the top of blade along the center line near the point where the clip was positioned.
6. If the fan wobble problem has not been corrected you may wish to try to improve the balancing further by using the balancing clip and additional weights.

REMOTE CONTROLINSTRUCTIONS

REMOTE SIGNALPARING:

if the remote control loses signal with the fan, turn off the power from the wall switch, then turn it back on, immediately press button (14) for around 3 seconds.
After the fixture beeps or flashes the reconnection is complete.

NOTE:
Please insert 2 batteries before using. AAA 1.5V battery x 2pcs (not included)

APP CONTROL INSTRUCTIONS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>