FUFUGAGA KF170352-01 Surface Frameless Medicine Cabinet with Mirror Instruction Manual
- June 1, 2024
- FUFUGAGA
Table of Contents
FUFUGAGA KF170352-01 Surface Frameless Medicine Cabinet with Mirror
Specifications
- Product: Cabinet
- Version: 12/01/2023
Preparation
Before starting assembly, ensure you have all the necessary tools listed in
the manual.
Assembly Steps
-
1. Screw eccentric rod(A) into board 5 as shown. - Attach board 11 to board 5 using wooden dowel(C), add cam lock(B) into board 11 and turn clockwise to tighten as shown.
- Continue following the detailed instructions in the manual for each board and component.
Important Safety Guidelines
- Always install tip-over restraints provided.
- Never put a TV on this product.
- Avoid allowing children to stand, climb, or hang on drawers, doors, or shelves.
- Do not open more than one drawer at a time.
- Place heaviest items in the lowest drawers.
Frequently Asked Questions (FAQ)
Q: What should I do if I don’t have the wall attachment to prevent tip-
over?
A: If the wall attachment is not included, please purchase one that fits
your wall and seek professional advice if unsure.
IMPORTANT INFORMATION!
please read the entire manual before starting to assemble and/or using this product.follow the manual thoroughly and keep it for further reference.
AVOID SCRATCHES!
In order to avoid scratching this furnuture should be assembled on a soft
layer-could be a rug.
IMPROVE EFFICIENCY !
Try to find a partner to install with you, which can speed up the installation
efficiency and shorten the time.
ANTI-TOPPLE WARNING!
Overturned furniture can cause serious or fatal crush injuries. To prevent
tipping over, be sure to use the wall attachment, if not included with this
product. Please purchase the wall attachment that fit your wall. If unsure,
seek professional advice. Please read and follow each step of the instructions
carefully.
IMPORTANT !
- It is important that any product which is assembled using any kind of screw is re-tightened
- weeks after assembly,and once every 3 months – in order to assure stability through-out the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.
When installing, please carefully confirm whether each screw corresponds to the manual, accessories with similar shapes can be distinguished by size
-
Screw eccentric rod(A) into board 5 as shown.
-
Attach board 11 to board 5 using wooden dowel(C), add cam lock(B) into board 11 and turn clockwise to tighten as shown.
-
Screw eccentric rod(A) into board 5 as shown.
-
Attach board 12 to board 5 using wooden dowel(C), add cam lock(B) into board 12 and turn clockwise to tighten as shown.
-
Screw eccentric rod(A) into board 1 as shown.
-
Attach board 6 to board 1 using wooden dowel(C), add cam lock(B) into board 6 and turn clockwise to tighten as shown.
-
Screw eccentric rod(A) into board 1 as shown.
-
Attach board 8 to board 1 using wooden dowel(C), add cam lock(B) into board 8 and turn clockwise to tighten as shown.
-
Connect board 1 to board 5 using wooden dowel(C), add cam lock(B) into board 5 and turn clockwise to tighten as shown.
-
Screw eccentric rod(A) into board 2 as shown.
-
Attach board 7 to board 2 using wooden dowel(C), add cam lock(B) into board 7 and turn clockwise to tighten as shown.
-
Connect board 2 to board 5 using wooden dowel(C), add cam lock(B) into board 5 and turn clockwise to tighten as shown.
-
Insert back board 9 along available grooves as shown.
-
Screw eccentric rod(A) into board 3 as shown.
-
Connect board 3 to board 2, 7, 6, 1, 8 and 11 using wooden dowel(C), add cam lock(B) into board 6,7,8 and turn clockwise to tighten as shown.
-
Fix back board 9 to the unit with screw(K) as shown. Insert back board 10 along available grooves as shown.
-
Screw eccentric rod(A) into board 4 as shown.
-
Connect board 4 to board 2, 7, 6, 1, 8 and 12 using wooden dowel(C), add cam lock(B) into board 6,7,8 and turn clockwise to tighten as shown.
-
Add cam lock(B) into board 1, 2, 11 and 12 and turn clockwise to tighten as shown.
-
-
Pay attention to the difference between the middle parts of the two types of door hinges.
- The flat door hinges(D) are used on the outermost door plates.
- And the curved door hinges(E) are used on the door panel in the middle of the cabinet.
-
Fix hinge(D) to board 13 with screw(F) as shown.
-
Assemble door 13 to board 3 by fixing hinge with screw(F) as shown.
-
Fix hinge(E) to board 14 with screw(F) as shown.
-
Assemble door 14 to board 5 by fixing hinge with screw(F) as shown.
-
Fix hinge(D) to board 15 with screw(F) as shown.
-
Assemble door 15 to board 4 by fixing hinge with screw(F) as shown.
-
If doors are still not aligned if the hinges are properly correctly, please watch the video. https://youtube/n0Lb36SoODM
-
-
Place the wire box(G) into the corresponding position at first.
-
Tear off the sticker of part(J), stick it to a proper place of board 1. Press to open the clamp, put in the power cord, and press to close.
Connect to Wall Switch
- plugs are provided with this product. Recommend to use the plug directly.
If you need to link wall switch, you can choose to cut off the plug and link the wire.
Note :
When the plug is cut off, the product is not covered by the warranty. It is
recommended that you contact an electrician to install it, or operate under
the guidance of a professional.
- Input Voltage 110V AC
- Output Voltage 12V DC
Touch Switch
Color temperature 3000K- 4000K- 6500K
rc51 1. ON/OFF/Switch-color Function
- Short Press to turn on/off and change the color temperature.
- Press the switch button and hold on for 2-3 seconds to active the dimmer function after turn on. After the lamp dimmer function is activated, the long press light switch brightness changes from dark to light, and the long press light brightness changes from light to dark.
Defogger button
- First short press,anti-fog function works.
- Second short press,anti-fog function stops.
- The two operations cycle in turn.
WARRANTY
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase.
- Before making a claim, we may be able to answer your query, simply call us. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. We will arrange within 48 hours. If there is out of stock, we will reply with a shipping date.
- The product must be used in accordance with the instructions provided. For health reasons.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty. Attention please.
- Does not include damage during installation, but includes damage during transportation.
Scope of responsibility
- Shall not bear any responsibility for misuse or user damage and / or loss of parts during the installation of furniture.
- After using, the damage and scratches of the furniture are not covered by the warranty.
- The Warranty Relates to All Bought in The Us and Covers The
Following Areas
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
RETURNS
CHANGED YOUR MIND AND NEED TO RETURN YOU ITEM?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
If you have purchased and have simply changed your mind, follow the retailer’s instructions for returns.
DEFECTIVE ITEMS
If your item is defective in any way, i.e. it doesn’t work but you can’t
identify why, in the first instance, please call us.
DAMAGED ITEMS
- If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
In all circumstances please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.
AFTER-SALES CONTACT
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>