W-KING Q8W-T11 Portable Party Speaker User Manual
- June 1, 2024
- W-KING
Table of Contents
User Manual
T11 Portable Party Speaker
Q8W-T11 Portable Party Speaker
W-KING® is a registered trademark in the U.S, European Union and Japan, All
rights reserved, Thank you for purchasing the W-KING T11 Outdoor Party
Speaker.
Please read this user manual carefully and keep it for future reference. If
you need any assistance, please contact our support team with your product
model number and order number.
Customer Support E-mail:
Amazon E-mail: support.amazon@w-king.com
Walmart E-mail:
support.walmarnt@w-king.com
Package Contents
T11 Portable Party Speaker
3.5mm Audio Cable
15V / 1.6A Adapter
User Manual
Product Diagram
- Microphone / Guitar Input
- Reset
- USB Port¢ AS Power Bank)
- USB Flash Drives Port
- AUX
- TF Card Slot
- Charging Port
Product Diagram
- WD ECHO – / ECHO+
- Microphone volume – / Microphone volume +
- True Wireless Stereo Pairing
- Play / Pause
- Volume – / Volume +
- Light Mode
- LED Indicator
- Battery Indicator
- Power ON / OFF
Specifications
Model Number | T11 |
---|---|
Technology | HFP V1.5;A2DP V1.2;AVRCP V1.4,GAVDP V1.2; AVDTP V1.2;SPP |
V1.2;AVCTP V1.2
Power Input| DC 15V (ADAPTER INCLUDED)
Bluetooth version| 5.
Output Power| 100W
Waterproof| IPX6
Frequency Range| 80Hz-18KHz
S/N| a75dB
Operating Range| 10 meters
Dimensions| 442mm-221mme205mm
Net Weight| 5406g±100g(bare unit)
THD| 51% at 1KHz 40W (BT input 1000mV)
True Wireless Stereo| Support
Power Bank function| Support; output: DC 5V / 2.1A
Music Source Input| Support Bluetooth / Aux / TF Card / USB Flash drives
Wired microphone function| Support 6.35mm wired microphone (Microphone not
included)
Wired guitar function| Support,When the ECHO is 0. (Guitar not included)
Charging
Fully charge this speaker before first use. Using the included W-KING Power Adapter ( DC 15V 1.6A) to charge your speaker. When there are 3 solid white lights, your speaker is fully charged and ready for use. Charging takes around 3.5 hours.
Battery
Battery Voltage | Battery Indicator |
---|---|
higher than 11.3V (70%) | Three lights are on |
10.6-11.3V (40%-70%) | Two lights are on |
lower than 10.6V (40%) | One light are on |
Low Battery
Low battery alarm
(When battery voltage is lower than 10V (20%) & 9.2V (10%))| REA LED flashes
---|---
automatically turn off at low batterry (When battery voltage is lower than
0%)|
Power Bank Function
- Press the power button for 1S to turn on the power bank function separately.
- When the power bank function is turned on alone, the load is detected in 10 seconds, If no load is detected during this period, the power bank function will be turned off.
- When the speaker is turned on, the power bank is always on, and when the speaker battery is lower than 20%, the power bank output will be turned off.
Notes: When the speaker is charging, the power bank will be forced to turn off.
Connection Way Bluetooth Connection
Actions | Operation | LED status |
---|---|---|
Pairing | Active the pairing function on your phone or other compatible | |
Bluetooth device and select “W-KING T11”. | Blue LED stays on (successfully |
paired)
Connected| Active the pairing function on your phone or other compatible
Bluetooth device and select “W-KING T11”.| Blue LED stays on (successfully
paired)
Disconnected manually| Long press the play / pause button for 2 seconds.| Blue
LED flashes
Reconnect| The speaker will reconnect with the last device when powered on.|
Blue LED stays on (successfully paired)
Clear Bluetooth pairing list| Press and hold the play / pause button for 10
seconds.| Cyan-blue LED flashes for 3 times
Notes
- To reset the speaker (to clear the pairing list or any program errors), use a straightened paper clip or a toothpick to carefully short-press the reset hole.
- The speaker will automatically shut down after 10 minutes in pairing mode if no devices are paired.
- If your paired device is switched off or manually disconnected, the speaker will enter pairing mode and automatically shut down after 10 minutes.
- If the speaker or connected device exceeds the operating range, the speaker will disconnect. The connection to the last successfully connected device will be re-established once you re-enter wireless range within 10 minutes. To connect to other devices, please repeat the previous “Pairing” steps.
Other Connection Ways
Actions | Operation | LED status |
---|
USB Drive
Playback| Plug your USB drive to the USB port of the speaker, Power on the
speaker and press the play /pause button.| Play: Steady green light (indoor
mode)
Play: Green light flashes slowly (outdoor mode)
Pause: Green light flashes
TF Card Playback| Just Insert TF card to enter T-flash card mode.| Play:
Steady green light (indoor mode)
Play: Green light flashes slowly (outdoor mode)
Pause: Green light flashes
Aux Mode| Just Insert 3.5mm Audio Cable to enter AUX mode.| Play: Steady green
light (indoor mode)
Play: Green light flashes slowly (outdoor mode)
Pause: Green light flashes
Notes
- The speaker will disconnect from your phone or other paired device when an audio cable is plugged into the audio input jack.
- When playing audio using the audio input jack, press the volume + / – to adjust the volume. and short-press play/pause to pause or resume. Next / previous track control on the speaker is disabled in audio input mode.
- For some computers, you may need to access the audio control panel to manually set the speaker as the default audio device.
Microphone / Guitar Function
MIC Volume Mode| When the microphone is inserted, short press “MIC VOL + / –
“button.
---|---
Guitar Volume Mode| When the guitar is inserted, short press “GUITAR VOL + / –
“button.
MIC ECHO Adjust| When the microphone is inserted, short press ” ECHO + /
-“button.
Guitar Function| When the guitar is inserted, short press the ‘ECHO -” button
until you hear a ‘bee” sound, then you can use the guitar function (when the
reverb effect is 0).
Notes: The guitar function can only be used when the reverb effect is 0.
True Wireless Stereo Pairing
The True Wireless technology enables you to use two speakers paring via
Bluetooth to create a wireless dual-channel system to deliver true stereo
sound effect.
Actions | Operation | LED status |
---|---|---|
Power on | Trun on both T11 bluetooth speakers(the distance should not be over |
10 meters, and make sure that the Bluetooth of your two speakers are not
connected).| Master speaker: Blue LED flashes.
True wireless Stereo| Select one speaker as the Master speaker, and Short
press the “ ”
button (any machine) in any mode, Enter True wireless stereo paring mode, True
wireless stereo paring default search time is one minute,
if not connected for one minute, it will automatically exit True wireless
stereo paring.| Master speaker : Blue and Green LED flash .
Slave speaker: Blue LED stays on.
Connection between two W-KING TI 1 speakers| Successfully connection| The Blue
LED indicator of the Master speaker flashes slowly and the Slave speaker LED
keep bright blue.
Connect with mobile| When True wireless stereo paring successfully connected,
turn on your phone’s Bluetooth, search “W-KING T11” and connect the Master
speaker.| Master and Slave speaker LED keeps bright blue.
Disconnect true wireless pairing| When True wireless stereo paring
successfully connected, Short
press the ” ” button, the true wireless stereo will be disconnected.| Master
speaker: Blue LED flashes.
Slave speaker: Blue LED flashes.
LED Lights Mode
Click ” ” button to change the LED Lights modes.
- Rotational pulsation from bottom to top.
- Half-circle rotation (rotate and chase with the rhythm of the music).
- Full cycle rotation (speed automatic).
- Brightness flashes to the beat of the music.
- Flow from the middle up and down.
- Turn off the lights
Basic Controls
Functions | Instructions |
---|---|
Adjust Volume | Short press volume button + / – |
Pause / Play | Press Play / Pause button |
Next / Previous track | Long press ” + / – ” button to Next / Previous |
track
Switch Mode| Short press power button to switch.
Light Mode| Short press ” ” light mode button
Equalizer Mode
Sound Effect Adjustment (EQ Modes) | LED Status |
---|
Long press the button ” ” for 2 seconds to switch between bass mode and treble
mode.| Bass Mode: Solid blue light
Treble Mode: Flashing blue light
Product Care & Use
Keep away from liquids, extreme heat, and strong magnetic fields. Do not use this speaker at high volume for extended periods, as this may cause permanent hearing damage or loss.
Warranty & Customer Support
For questions, support, or warranty claims, contact us at Amazon E-mail:
support.amazon@w-king.com
Walmart E-mail:
support.walmart@w-king.com
Please include your order number and product model number.
*Notes: W-KING can only provide after sales service for products
purchased directly from our official online store.
SHENZHEN WEIKING TECHNOLOGY CoO., LTD
CN, 518109, Guangdong, Shenzhen, Longhua
Fucheng Street, Znhangge Community. Zhangge Road
NO.142, Building 1, Room 301
Tel: +86-755-36690577
Fax: +86-755-368 15032
Amazon
E-mail:support.amazon@w-king.com
Walmart
E-mail:support.walmart@w-king.com
www.w-king.com
Documents / Resources
|
W-KING Q8W-T11 Portable Party
Speaker
[pdf] User Manual
Q8W-T11 Portable Party Speaker, Q8W-T11, Portable Party Speaker, Party
Speaker, Speaker
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>