TAC 3B-N113T Bull Bar Instruction Manual

June 1, 2024
TAC

TAC 3B-N113T Bull Bar

TAC-3B-N113T-Bull-Bar-product-image

Specifications:

  • Product: Bull Bar
  • Compatible with: 2022-2024 Nissan Frontier
  • Part Number: 3B-N113T

Product Usage Instructions

Parts List:

  • 1 Bull Bar
  • 1 Driver/Left Side Frame Bracket
  • 1 Passenger/Right Side Frame Bracket
  • 4 12-1.25mm x 45mm Special Fine Thread Hex Bolts
  • 4 12-1.75mm x 35mm Coarse Thread Hex Bolts
  • 12 12mm x 37mm x 3mm Flat Washer
  • 8 12mm Lock Washer
  • 4 12mm Hex Nuts

Installation Procedure:

  1. Remove contents from the box and verify all parts are present.
  2. Read instructions carefully before starting installation. Note: Minor cutting may be required, and assistance is recommended.
  3. Remove the driver/left factory tow hook, if equipped.
  4. Select the driver/left side Frame Mounting Bracket and attach it to the tow hook.
  5. Hold the splash guard in place against the brackets and mark the bracket location onto the splash guard.
  6. Cut slots out of the splash guard to clear the brackets and then reinstall the splash guard.
  7. Do periodic inspections to ensure all hardware is secure and tight.

Maintenance Instructions:
To protect your investment, wax the product after installing. Regular waxing is recommended to add a protective layer over the finish. Avoid using any polish or wax that may contain abrasives as they could damage the finish. Mild soap can be used to clean the Bull Bar.

FAQ

  • Q: Can I install the Bull Bar without assistance?
    A: While it is recommended to have assistance during installation, it is possible to install the Bull Bar by following the provided instructions carefully.

  • Q: How often should I conduct inspections on the installation?
    A: It is advisable to do periodic inspections to ensure that all hardware remains secure and tight. Check the installation regularly for any signs of loosening or damage.

INSTALLATION INSTRUCTIONS
3” BULL BAR
2022-2024 NISSAN FRONTIER
PART# 3B-N113T
www.tacautoparts.com

PARTS LIST

1 Bull Bar
1 Driver/Left Side Frame Bracket
1 Passenger/Right Side Frame Bracket
4 12-1.25mm x 45mm Special Fine Thread Hex Bolts
4 12-1.75mm x 35mm Coarse Thread Hex Bolts
12 12mm x 37mm x 3mm Flat Washer
8 12mm Lock Washer
4 12mm Hex Nuts

TAC-3B-N113T-Bull-Bar-fig- \(1\)

INSTALLATION INSTRUCTIONS

PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. MINOR CUTTING MAY BE REQUIRED. ASSISTANCE IS RECOMMENDED. INSTALLATION MAY INTERFERE WITH FRONT SENSOR OPERATION.

  1. Determine if vehicle is equipped with lower splash guard, (Figure 1).
    Models with splash guard.

  2. Start installation from the driver/left wheel opening. Remove the hardware attaching the inner fender liner to the edge of the fender, (Figure 2). Remove the screws attaching the end of the lower splash guard to the bottom of the fender, (Figure 3).

  3. Repeat previous Step to release the passenger/right end of the splash guard.

  4. Continue across the bottom of the vehicle and remove the rest of the hardware to remove the splash guard, (Figures 1 & 4).
    Models without splash guard. (Pro 4X model for example-see Figure 5). Skip to Step 2.

  5. Remove the driver/left factory tow hook, if equipped, (Figures 1 & 5).

  6. Select the driver/left side Frame Mounting Bracket, (Figure 6). Attach the Bracket to the tow hook location on the bottom of the frame channel with the included (2) 12mm x 45mm Fine Thread Hex Bolts, (2) 12mm Lock Washers and (2) 12mm Flat Washers, (Figures 6 & 7). NOTE: Models with tow hooks, reinstall tow hook with Bracket between tow hook and frame. Do not fully tighten hardware.

  7. Repeat Steps 2 & 3 for the passenger/right side Mounting Bracket installation.

  8. Carefully unwrap the Bull Bar.

  9. With assistance, hold the Bull Bar up to the outside of the Brackets. Attach the Bull Bar to the Brackets with the included (4) 12mm x 35mm Coarse Thread Hex Bolts, (8) 12mm Flat Washers, (4) 12mm Lock Washers and (4) 12mm Hex Nuts, (Figures 8 & 9).

  10. Level and adjust the Bull Bar properly and tighten all hardware.
    Models with splash guard only:

  11. Hold the splash guard up in place against the bottom of the Brackets. Mark the Bracket location onto the splash guard, (Figure 10). Use a knife or hacksaw blade to cut slots out of the splash guard to clear the Brackets, (Figure 11).

  12. Reinstall splash guard.

  13. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Bull Bar.

Driver/left Side Installation Pictured

TAC-3B-N113T-Bull-Bar-fig- \(2\) TAC-3B-N113T-Bull-
Bar-fig- \(3\)

TAC-3B-N113T-Bull-Bar-fig- \(4\) TAC-3B-N113T-
Bull-Bar-fig- \(5\) TAC-3B-N113T-Bull-Bar-fig-
\(6\) TAC-3B-N113T-Bull-Bar-fig- \(7\)

www.tacautoparts.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals