Assault SW-U-350RS 350R Suede UTV Steering Wheel Instruction Manual
- June 3, 2024
- ASSAULT
Table of Contents
Assault SW-U-350RS 350R Suede UTV Steering Wheel
STEERING WHEELS 6 ACCESSORIES
FROM THE TOOLBOX
- Hex Key Sets
- Socket Set
- Thread Locker (Optional)
- Variable Torque Impact
INSTALLATION
- Make sure your wheels are at zero (completely straight) before removing the OEM steering wheel.
- Unbolt and remove the OEM steering wheel. If it is difficult to remove, a steering wheel removal tool may be required to slide the wheel off of the taper.
- Inspect the splines and threads on the column, clean dirt debris and thread locker before proceed- ing to the next step.
- Install the hub logo side up with mount hole on “center”. The logo should appear slightly offset.
- Do not install the nut yet add the steering wheel with a couple of bolts, get in the vehicle and drive it forward about 10-15 feet or enough to see if the wheel is tracking straight. If it is not exactly straight stop, remove the wheel with hub attached and rotate it to the left or right on the spline and repeat this step until the wheel tracks correctly going in a straight line.
- Once installed and tracking is satisfactory, park the vehicle, thread the nut onto the column, holding the wheel you can use an impact on a low setting or tighten with a ratchet. The nut should have an integrated nylon lock. Torque the nut to 30-35lbs. ft.
- Remove the bolts holding the steering wheel in place and set it aside for optional accessories if applicable.
- Quick Release: Holding the quick release mount with 2 hands, press the button and pull back the sleeve to release the male end from the main body.
- Using the supplied bolts install the male portion of the adapter to the hub. There is an indentation at the top of the base.
- That is the top. A dab of blue thread locker can be used to prevent bolts trom loosening over time but it is not required. The main body will be installed directly to the back of the wheel.
- Push To Talk Plate (PT): The PT plate installs between wheel and the quick release main body or if not using a quick release install between wheel and hub.
- Place the optional accessories on a flat surface (if applicable) – first the main body of the quick release (The button should be at the top), then the PTT, aligning holes appropriately.
- Then place the wheel on top and orient the PT where it will be most comfortable tor your set up. Add the top plates for the wheel and then install the bolts to hold it all together. Thread locker can be used in this step but is not required.
- Place the wheel on the male end of the quick release, if the wheel does not engage you can rotate until it catches. Once it locks in place, the install is complete.
ATTENTION : USE OF THESE PRODUCT IS AT YOUR OWN RISK. YOU ASSUME ALL LIABILITY.
WARNINGS : MOTORSPORTS, RACING, AND VEHICLE MODIFICATION ARE INHERENTLY DANGEROUS ACTIVITIES THAT CAN RESULT IN DEATH, BRAIN DAMAGE, PARALYSIS OR SERIOUS PERSONAL INJURY. YOU ASSUME THE RISK OF INJURY OR DEATH WHENEVER PARTICIPATING IN MOTORSPORTS, RACING AND VEHICLE MODIFICATION. IF YOU DO NOT UNDERSTAND OR APPRECIATE THE DANGER OF THESE ACTIVITIES, PLEASE REFRAIN FROM ALL MOTORSPORTS ACTIVITY AND FURTHER USE OF ASSAULT INDUSTRIES PRODUCTS. NO WARRANTIES: ALL PRODUCTS AND PARTS ARE SOLD “AS IS” WITHOUT ANY WARRANTY WHATSOEVER. EXPRESS WARRANTIES, IMPLIED WARRANTIES, WARRANTIES OF MERCHANTABILITY AND WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. THE ENTIRE RISK OF QUALITY AND PERFORMANCE OF SUCH PRODUCTS AND PARTS IS WITH THE BUYER, USER, SUBSEQUENT USER, OR AGENT THEREOF (HEREIN “USER”). SHOULD SUCH PRODUCTS OR PARTS PROVE DEFECTIVE FOLLOWING THEIR PURCHASE, THE BUYER AND NOT THE MANUFACTURER(S), DISTRIBUTOR(S), OR RETAILER(S), ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICES OR REPAIR AS RESULT OF A PART(S) FAILING.
NOT LIABLE FOR DAMAGES : In no event will Assault Industries, or its affiliates be liable for any special, direct, incidental or consequential damages, or any damages whatsoever, including, without limitation, the loss of life or limb, or damages due to bodily or personal injury, which may arise or result from the sale, installation, or use of any of its products and parts.
BUYER’S/USER’S RESPONSIBILITIES : It is the BUYER’S/user’s responsibility
to inspect and verify the dimensions, specifications, and performance of all
products and parts as being appropriate for the use to which the BUYER/user
will USE them prior to any actual installation and/or use of said products and
parts. ALL products and parts are to be inspected by the user before each use
for evidence of damage, defect or wear. Any deviation by the user from the
manufacturer’s
specifications concerning use, maintenance, repair, alterations and
modifications constitutes willful negligence.
VEHICLE MODIFICATIONS: Vehicle modifications can potentially affect
safety, handling, stability and emissions compliance. Suspension modifications
can negatively affect stability and increase the chance of rollover. The
consumer accepts all
responsibility for all resulting changes and modifications to said vehicle(s)
and all potential risks AND FINES/IMPRISONMENT FOR NON-COMPLIANCE WITH STATE
AND FEDERAL LAWS. The installation of ASSUALT INDUSTRIES’ products or parts
may adversely affect other vehicle components, safety equipment or
manufactured goods (collectively “goods”). ASSUALT INDUSTRIES assumes no
responsibility for any damage to other goods, or bodily injury that may arise
due to failure of other goods, due to installation and/or use, either proper
or improper, of its products or parts.
SAFETY CLAIMS: No warranty or representation is made as to this product’s
ability to protect the user from injury or death. the BUYER/user IS
responsible for HIS/HER own actions and decisions. No safety product can
completely protect the
user from injury or death.
SEVERANCE OF DISCLAIMER PROVISIONS: By purchasing or using this product,
the BUYER/user agrees that if any provision of this Disclaimer is held to be
illegal, invalid or unenforceable under present or future law, such provision
shall be fully severed from the Disclaimer and this Disclaimer shall be
construed and enforced as if such illegal, invalid or unenforceable provision
never comprised a part hereof, and the remaining provisions hereof shall
remain in full force and effect and
shall not be affected by the illegal, invalid or unenforceable provision.
there shall be added automatically as part of this Disclaimer a provision as
similar in its terms to such illegal, invalid or unenforceable provision as
may be possible and be
legal, valid and enforceable.
TERMS AND CONDITIONS
DEFINITIONS USED HEREIN: “Agreement” means this document, including any
attached or affixed pages (e.g. purchase orders, invoices, etc.) and the terms
and conditions contained herein. “Assault” means Assault Industries, a
California
corporation, including any affiliate, successor or predecessor companies.
“Buyer” means the Buyer identified in any order of Goods which is hereby made
a part of this Agreement. “Goods” means the goods, materials, parts, supplies
and/or
services supplied by Assault to Buyer.
COMPLETE AGREEMENT: All purchases of Goods by Buyer are subject to the
terms and conditions of this Agreement regardless of other or additional terms
or conditions that conflict with or contradict this Agreement in any purchase
order,
document, or other communication. Preprinted terms and conditions on any
document of Buyer and/or Assault failure to object to conflicting or
additional terms will not change or add to the terms of this Agreement. This
Agreement
supersedes and replaces all previous requests, quotations, orders or
agreements concerning the Goods. Any additional or different terms will not
become part of the contract or agreement for the sale of the Goods and are
hereby objected to
by Assault without further notice unless made in writing and signed by an
authorized representative of Assault. The terms and conditions are subject to
change and upon such change those terms and conditions shall control all
future orders
from Buyer.
PRICES AND PAYMENT: Prices are subject to change at any time without
notice. All orders are subject to acceptance by Assault, as Assault may refuse
to complete any order for any lawful reason and/or Assault has any reason to
believe that
Buyer’s Representations and Warranties in Paragraph 14 are false and/or
misleading. Any applicable taxes or other governmental impositions, which
Assault may be required to pay or collect, will be added to the price and paid
by Buyer unless
Assault receives a valid exemption certificate. Payment in full is due at time
of order. All sales are final.
TITLE, DELIVERY AND RISK OF LOSS: Unless otherwise stated, Assault best judgment will be used in routing shipments and subject to its Shipping Policy. Title to the Goods and liability for loss or damage in transit or thereafter shall pass to Buyer upon Assault delivery of the Goods to a common carrier for shipment. Shipping dates are not guaranteed. Assault disclaims any direct or indirect liability for any damages suffered by Buyer which result from delays in delivery.
SHORT, DAMAGED OR DEFECTIVE GOODS: Buyer agrees to inspect all Goods
within three days of receipt when shipped, or immediately upon receipt if
delivered in person from Assault personnel to Buyer. After that time all Goods
are deemed to be accepted. Claims for Goods delivered short, errantly, damaged
or defective (not due to fault of carrier) shall be filed in writing with
Assault within five days after date of shipment. Upon acceptance of Buyer’s
timely written claim and issuance of a written return authorization (RA),
Assault agrees to repair, replace, or, at Assault option, issue credit for all
defective Goods which have not been altered, machined or finished, provided
the Goods are returned unaltered with a valid RA to
Assault facility within 20 days of shipment. Assault reserves the right to
refuse delivery of any Goods returned without a valid RA. Buyer must prepay
all freight, which will be reimbursed by Assault for defective, damaged or
errant Goods.
Claims for Goods delivered short, errant, damaged or defective as a result of
the fault of the carrier will be handled by Buyer directly with the carrier.
EXCUSABLE DELAYS: No liability shall result from delay in performance or
non performance, directly or indirectly caused by circumstances beyond Assault
control, which include, but are not limited to, Acts of God, fire, explosion,
flood, war,
terrorism, act of or authorized by any government, accident, labor trouble, or
shortage or inability to obtain material, equipment or transportation.
Quantities so affected may be eliminated from the Agreement without liability,
but the Agreement
shall remain otherwise unaffected.
LIMITED WARRANTY AND WARRANTY DISCLAIMER : Assault warrants its Goods to
be free from material defects in material and workmanship for 90 days from
delivery except: (a) when Goods have been modified or altered following
delivery and/or subject to improper handling, storage, installation,
operation, or maintenance; (b) when an item is purchased by Assault as a
component part of the Goods, except to the extent to which such item or items
are covered by the warranty, if any, of the original manufacturer; (c) when
any component of or instrument used to manufacture the Goods was provided or
sold to Assault by Buyer, or otherwise specified by Buyer; and (d) no warranty
of a component part shall extend beyond the
warranty period of the device in which such component part is incorporated.
Any claim by Buyer made pursuant to Assault warranty must be made in writing
during the warranty period. Assault shall have the right to inspect the Goods
claimed
to be defective and shall have the right to determine the cause of such
alleged defect. Assault agrees to repair, replace, or, at Assault option,
issue credit for all Goods deemed defective under Assault limited warranty.
All Goods replaced or
repaired by Company under its warranty shall be replaced or repaired F.O.B.
Assault facility. Except as expressly stated herein, Assault makes no other
warranties concerning the Goods whatsoever. THE AGENTS AND EMPLOYEES OF
ASSAULT ARE NOT AUTHORIZED TO MAKE MODIFICATIONS EITHER WRITTEN OR ORAL TO THIS WARRANTY OR AGREEMENT, OR ANY ADDITIONAL WARRANTIES WHICH MAY BE BINDING UPON ASSAULT. ACCORDINGLY, ADDITIONAL STATEMENTS BY ANY EMPLOYEE OR AGENT OF ASSAULT, WHETHER ORAL OR WRITTEN, DO NOT CONSTITUTE WARRANTIES AND SHOULD NOT BE RELIED UPON BY BUYER, ITS EMPLOYEES, AGENTS, REPRESENTATIVES OR ANY THIRD PARTY. ASSAULT DISCLAIMS AND EXCLUDES ANY AND ALL OTHER EXPRESS WARRANTIES AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
LIMITATIONS OF REMEDIES AND DAMAGES: Buyer agrees that Assault
obligations described in Paragraph 7 is Buyer’s sole and exclusive remedy, and
that Assault total liability to Buyer, Buyer’s customers or to any other
person, relating to this Agreement, its performance or non-performance, or
from the use of Goods furnished, is limited to the price of the Goods and/or
services giving rise to the claim. Except as to title, such obligation and
liability shall terminate 90 days from
delivery. ASSAULTAND ITS SUPPLIERS WILL NOT, IN ANY EVENT, BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, CONSEQUENTIAL OR PENAL DAMAGES INCURRED IN CONNECTION
WITH THE GOODS, WHETHER
ANY CLAIM FOR
RECOVERY IS BASED UPON OR ARISES OUT OF THEORIES OF CONTRACT, NEGLIGENCE, TORT
(INCLUDING STRICT LIABILITY) OR OTHERWISE, including, but not limited to back
charges; labor costs; costs of removal, replacement, testing or installation;
loss of efficiency; loss of profits or revenues; loss of use of the Goods or
any associated products; damages to associated products; lateness or delays in
delivery; unavailability of Goods; cost of capital; cost of substitute Goods,
facilities or service; downtime; or claims from Buyer’s customers or other
parties to Buyer or directly to Assault for such damages.
INDEMNITY : Buyer shall release, indemnify, defend and hold Assault
harmless, and its present and future officers, directors, officials,
employees, agents, subsidiaries, affiliates, successors and assigns from any
and all liability (including without
limitation liability for negligence or strict liability), claims, losses,
suits, demands, penalties, fines, forfeitures, damages and costs (including
reasonable attorney’s fees) caused by, arising out of or relating to: (a) any
form of intellectual property
claim related to designs, instructions, specifications or intellectual
property developed or furnished by Buyer; (b) any claim related to any
component of or instrument used to manufacture the Goods provided or sold to
Assault by Buyer, or
otherwise specified by Buyer; (c) any claim related to the combination of the
Goods with any hardware, text, graphics, software or other device supplied or
specified by Buyer, and (d) any claim arising from the modification or
alteration of the
Goods by Buyer; (e) Buyer’s negligent, unlawful, or improper use of the Goods
and (f) any liens, liabilities, damages, costs, expenses and the like arising
out of or related to any form of claim covered under this Paragraph.
CLERICAL ERRORS: Stenographical and clerical errors are subject to correction.
APPLICABILITY: This document and any subsequent Agreement referred to
herein shall be governed by and construed in accordance with the laws of the
State of California, including the California Uniform Commercial Code. This
Agreement
shall binding upon the successors, assigns, affiliates and any other related
third parties of Buyer.
SEVERABILITY: Invalidity of any of the terms provided herein shall not affect the validity of any other term.
WAIVER : Waiver by Assault of Buyer’s performance, or inaction with
respect to Buyer’s breach of any provision of this Agreement, or failure of
Assault to enforce any provision of this Agreement, will not be deemed a
waiver of future
compliance or deemed a course of performance modifying such provision, and
such provision will remain in full force and effect as written.
REPRESENTATIONS AND WARRANTIES : By placing an order with Assault, Buyer
represents and warrants all of the following are true and correct as Assault
is specifically relying on all of Buyer’s representations and warranties in
agreeing to
accept and fulfill Buyer’s order: (1) Buyer has independently verified all
applicable federal, state, and local laws and confirmed Buyer is lawfully
permitted to purchase and own the Goods, (2) that Buyer will only modify or
alter the goods in
compliance with all applicable federal, state, and local laws; (3) the Buyer
acknowledges and accepts that the Goods, unless expressly stated otherwise,
have not been registered with any governing body; (4) that Buyer will not
transfer the
Goods if altered or modified unless expressly permitted by applicable law; (5)
that Buyer will only use the Goods in compliance with all applicable laws to
which Buyer may be subject; and (6) Buyer has not relied on any statement made
or
implied by Assault in making any representation or warranty in this Paragraph.
LEAVE US FEEDBACK
Visit Assaultind.com and leave a review of your product purchase. We
appreciate your opinion … even if you’re wrong! :).
NEED ADDITIONAL HELP?
- Check out our YouTube channel
- Call us: 714-799-6711
- Monday – Friday: 8am-5pm
- Email: [email protected]