audion SR 1.500 Car Audio Amplifiers Speaker User Manual
- June 1, 2024
- audion
Table of Contents
- audion SR 1.500 Car Audio Amplifiers Speaker
- Specifications
- Product Usage Instructions
- PRECAUTIONS
- SAFETY CONSIDERATIONS
- PACKAGING CONTENTS
- INSTALLATION AND SIZES
- CABLE SIZE CALCULATION TABLES
- INSTALLATION EXAMPLES
- BLOCK DIAGRAMS
- TECHNICAL SPECIFICATIONS
- FAQ
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
audion SR 1.500 Car Audio Amplifiers Speaker
Specifications
- Model: VCR-S2
- SR 1.500: (1CH) FILTERED SUBWOOFER
- SR 4.300: Ferrules x 2
- SR 4.500: Remote IN / OUT cable x 1, Speaker IN cable, HEX KEY 3 mm x 1, SCREWS 4,2 x 55 mm x 4, Fuse 35A x 2
- SR 5.600: HEX KEY 2 mm x 1, Ferrules x 2
- SR 6.600: Remote IN / OUT cable x 1 x 2, Speaker IN cable, SCREWS 4,2 x 55 mm x 4, Fuse 25A x 2, Ferrules x 2
Product Usage Instructions
- Packaging Contents
- Ensure all components listed in the packaging contents are included before proceeding with the setup.
- Set-up Controls
- Follow the instructions provided in the manual for setting up the controls specific to your model.
- Adjustment Controls
- Refer to the manual for detailed information on adjusting the controls for optimal performance.
PRECAUTIONS
Before installing the components, please carefully read all of the instructions contained in this manual. It is advisable to carefully follow the highlighted instructions. Failure to respect these instructions may cause unintentional harm or damage to the components.
SAFETY CONSIDERATIONS
- Make sure your car has a 12 VDC voltage negative ground electric system.
- Check your alternator and battery condition to ensure they can handle the increased consumption.
- Do not carry out any installation inside the engine compartment or be exposed to water, excessive humidity, dust or dirt.
- Never run cables outside the vehicle or install the amplifier next to electronic gearcases.
- Install the amplifier in the vehicle parts where the temperature is between 0°C (32°F) and 55°C (131°F). Let the amplifier’s outer profile be at least 5 cm (2”) away from possible walls. There must be good air circulation where the amplifier is installed. If you cover the heat sink, the amplifier goes in protection.
- The amplifier can reach temperatures of around 80°C (176°F). Make sure it is not dangerously hot before touching it.
- Periodically clean the amplifier without using aggressive solvents that might damage it. Don’t use compressed air, since it would push solid parts in the amplifiers. Dampen a piece of cloth with water and soap, wring it and clean the amplifier. Then use a piece of cloth dampened with water only; eventually, clean the amplifier with a dry piece of cloth.
- Make sure the location you chose for the components does not affect the correct functioning of the vehicle’s mechanical and electrical devices.
- Make sure the power cable is not short-circuited during installation and connection with the battery.
- Use extreme caution when cutting or drilling the car plate, checking there are no electrical wiring or structural elements underneath.
- When positioning the power supply cable, avoid running the wire over or through sharp edges or close to moving mechanical devices. Use rubber grommets to protect the wire if it runs in a hole of the plate or proper materials if it is close to heat-generating parts.
- Make sure all the cables are properly secured all along their length. Also, make sure their outer protective jacket is flame-resistant and self-extinguishing. Use a clamping screw to secure positive and negative cables just close to the amplifier’s respective power supply terminal blocks.
- Choose the cable gauge according to the amplifier power and to the suggestions you can find here. Use high-quality cables, connectors and accessories, as you can find in the Connection catalogue.
- Pre-plan the configuration of your new amplifier and the best wiring routes to ease installation.
- To avoid incidental damage, keep the product in the original packaging until you are ready for the final installation.
- Always wear protective eyewear when using tools, as splints or product residue may become airborne.
TYPICAL INSTALLATION SEQUENCE
If you have any questions please refer to the User’s Manual you can find
available on www.audison.com or contact your AUDISON dealer or AUDISON
authorized service for assistance.
- Before installing the amplifier turn off the source and all other electronic devices in the audio system to prevent any damage.
- Using a cable with adequate AWG (see chart: Power Supply Cable), run the power wire from the battery location to the amplifier mounting location.
- Connect the power supply with the correct polarity. connect (+) terminal to the cable coming from the battery and the (-) terminal to the car chassis.
- Put an insulated fuse holder 40 cm max far from the battery positive terminal; connect one end of the power cable to it after the other end to the amplifier. Do not mount the fuse.
- To ground the device (-) in the right way, use a screw in the vehicle chassis; scrape all paint or grease from the metal if necessary, checking with a tester that there is continuity between the battery negative terminal (-) and the fixing point. If possible, connect all components to the same ground point; this solution rejects most noise that can be generated during the audio reproduction.
- Route all signal cables close together and away from power cables.
- Connect the RCA input cables, the applied signal must be between 0.2 VRMS and 5 VRMS. (SR 6.600: 0.32 VRMS – 8 VRMS)
- Connect the high-level inputs using the proper plug. The applied signal must be between 0.8 VRMS and 20 VRMS. (SR 6.600: 1.6 VRMS – 40 VRMS) Don’t use it if you are already using a Pre In preamplified connection.
- Connect the speaker output using a 10 AWG max speaker cable.
- Don’t connect (-) L and (-) R speaker outputs together. If you use an external stereo crossover, make sure that its negative poles are not connected.
- The amplifier turns on by connecting the remote turn-on terminal (REMOTE IN) to the source-specific output. The amplifier turns on automatically, without a remote signal, and also if using high-level inputs (Speaker IN) by setting the “AUTO TURN ON” switch to position ON.
- The LED on the top panel lights up blue indicating that the product is on. The LED lights up red if the outputs go on overload if the thermal protection is triggered, if the speaker cables short circuit with the vehicle chassis and if the amplifier is malfunctioning.
- The fuse/s is/are located near the power supply and speaker terminals. To replace, remove the fuse/s from the housing. Always replace the fuse of the same rating.
- Secure all auxiliary devices you built to install the components to the vehicle structure; this ensures stability and safety while driving. The amplifier detachment while driving can seriously damage the people in the vehicle and other cars.
- When installation is over, check the system’s wiring and make sure all connections were done in the right way.
- Put the fuse into the fuse holder. The fuse value will have to be 30% higher than the amplifier built-in one. In case the cable supplies several amplifiers, the fuse value will have to be 30% higher than the sum of the values of all other fuses in the amplifiers.
- Listening level calibration is made by adjusting the source volume up to 3/4 of its maximum level; then, adjust the amplifier levels until you hear distortion.
- Warranty Certificate: please check out the AUDISON website for further information.
SAFE SOUND
USE COMMON SENSE AND PRACTICE SAFE SOUND. PLEASE REMEMBER THAT LONG EXPOSURE
TO EXCESSIVELY HIGH SOUND PRESSURE LEVELS MAY DAMAGE YOUR HEARING. SAFETY MUST
BE AT THE FOREFRONT WHILE DRIVING
Information on electrical and electronic equipment waste (for those European
countries which organize the separate collection of waste)
Products that are marked with a wheeled bin with an X through it can not be disposed of together with ordinary domestic waste. These electrical and electronic products must be recycled in proper facilities, capable of managing the disposal of these products and components. To know where and how to deliver these products to the nearest recycling/disposal site please contact your local municipal office. Recycling and properly disposing of waste contributes to the protection of the environment and prevents harmful effects on health.
PACKAGING CONTENTS
INSTALLATION AND SIZES
CABLE SIZE CALCULATION TABLES
- Power supply cable
- Speakers cable
POWER SUPPLY and REMOTE IN CONNECTION / FUSE REPLACEMENT
S UBWOOFER REMOTE VOLUME CONTROL: VCR-S2 INSTALLATION
PRE IN / SPEAKER IN / PRE OUT
AUTO TURN ON BY SPEAKER IN (without REMOTE IN)
INSTALLATION EXAMPLES
1CH: FILTERED SUBWOOFER
1CH: FILTERED 2 X 2Ω SUBWOOFER
4CH: A Ch + B Ch
INPUTS: INPUT A
Using also B Ch
4CH: WOOFER + MID/HI
3CH: FRONT + SUB
INPUT: INPUT A Ch
3CH: FRONT + SUB
Using also B Ch INPUT to drive SUBWOOFER:
2CH: BRIDGE LEFT + RIGHT
5CH: FRONT + REAR + SUB
5CH: 2 WAY FRONT + SUB
3CH: FRONT + SUB
6CH: 3 WAY FRONT
5CH: FRONT + REAR + SUB
3CH: FRONT + SUB
BLOCK DIAGRAMS
TECHNICAL SPECIFICATIONS
POWER SUPPLY
Nominal power supply voltage / fuse| 11 ÷ 15 VDC / 2
x 35 A
Pulse Operating voltage| 6.5 ÷ 17 VDC
Idling current| 0.8 A
Idling current when off| 0.02 mA
Consumption @ 14.4 VDC, MIN load impedance (Max Musical
Power)| 40 A
Remote IN| 6.5 ÷ 15 VDC (1 mA)
Remote OUT| 6.5 ÷ 15 VDC (150 mA)
ART – Automatic Remote Turn on/off
from OUTPUT BTL speakers
| 1.5 ÷ 7 VDC
AMPLIFIER STAGE
Distortion – THD @ 100 Hz, 4Ω,
70% Rated Power
| 0.1%
Damping factor @ 100 Hz, 4Ω, 2 VRMS| > 300
Bandwidth @ -3 dB| 10 Hz ÷ 500 Hz
S/N ratio (A weighted @ 1 V Input)| 100 dBA
Pre-In sensitivity| 0.2 ÷ 5 VRMS
Speaker-In sensitivity| 0.8 ÷ 20 VRMS
Minimum load impedance| 1Ω
Output power (RMS) @14.4 VDC, 1%
THD:
1Ch| 500 W x 1 (4Ω)
1Ch| 800 W x 1 (2Ω)
1Ch| 1000 W x 1 (1Ω)
CEA SPECIFICATION
Output power @ 4Ω 1% THD+N, 14.4 V | 500 W x 1 Ch |
---|---|
SN ratio (ref. 1 W output) | 75 dBA |
INPUTS / OUTPUTS / FILTERS
Inputs| Pre-In / Speaker-In
PRE OUT Hi-Pass filtered| 50 ÷ 250Hz @ 12 dB/Oct.
Filters| Full
LP 50 ÷ 250Hz @ 24 dB/Oct.
Phase (adjustable)| (0 ÷ 180) deg
Bass Boost 50Hz (adjustable)| (0 ÷ 12) dB
SUBSONIC (on/off)| 25 Hz @ 24 dB/Oct.
SUB Remote Volume Control| (-20 ÷ 6) dB
SIZE
Max size (mm/inch)| 264 x 155 x 47,5 / 10.39 x 6.10 x 1.87
Weight (kg/lbs)| 2,23 / 4.91
POWER SUPPLY
Nominal power supply voltage / fuse| 11 ÷ 15 VDC / 1
x 30 A
Pulse Operating voltage| 6.5 ÷ 17 VDC
Idling current| 1.6A
Idling current when off| 0.03 mA
Consumption @ 14.4 VDC, MIN load impedance (Max Musical
Power)| 25A
Remote IN| 6.5 ÷ 15 VDC (1 mA)
Remote OUT| 6.5 ÷ 15 VDC (150 mA)
ART – Automatic Remote Turn on/off
from OUTPUT BTL speakers
| 1.5 ÷ 7 VDC
AMPLIFIER STAGE
Distortion – THD @ 1 kHz, 4Ω, 70% Rated Power| 0.03 %
Damping factor @ 1 kHz, 4Ω, 2 VRMS| 150
Bandwidth @ -3 dB| 10 Hz ÷ 35 kHz
S/N ratio (A weighted @ 1 V Input)| 100 dBA
Pre-In sensitivity| 0.2 ÷ 5 VRMS
Speaker-In sensitivity| 0.8 ÷ 20 VRMS
Minimum load impedance
| @ 4Ch: 2Ω
@ 3Ch: 2Ω + 2Ω + 4Ω
@ 2Ch: 4Ω
Output power (RMS) @14.4 VDC, 1%
THD:
4Ch| 85 W x 4 (4Ω)
4Ch| 130 W x 4 (2Ω)
3Ch| 80 W x 2 (4Ω) + 250 W x 1 (4Ω)
3Ch| 130W x 2 (2Ω) + 260 W x 1 (4Ω)
2Ch| 250 W x 2 (4Ω)
CEA SPECIFICATION
Output power @ 4Ω 1% THD+N, 14.4 V | 75 W x 4 Ch |
---|---|
SN ratio (ref. 1 W output) | 82 dBA |
INPUTS / OUTPUTS / FILTERS
Inputs| Pre-In / Speaker-In
Outputs| PRE OUT full range (Input A)
A Ch Filters:
| Full
Hi-pass: 50 ÷ 3.2k Hz @ 12 dB/Oct.
Lo-pass: 50 ÷ 3.2k Hz @ 12 dB/Oct.
B Ch Filters:
| Full
Hi-pass: 50 ÷ 3.2k Hz @ 12 dB/Oct.
Lo-pass: 50 ÷ 3.2k Hz @ 12 dB/Oct.
A Ch MONO IN (on/off)| Yes
B Ch MONO IN (on/off)| Yes
Bass Boost 50Hz (adjustable)| B Ch (0 ÷12) dB.
SIZE
Max size (mm/inch)| 190 x 155 x 47,5 / 7.48 x 6.10 x 1.87
Weight (kg/lbs)| 1,56 / 3.44
POWER SUPPLY
Nominal power supply voltage / fuse| 11 ÷ 15 VDC / 2
x 25A
Pulse Operating voltage| 6.5 ÷ 17 VDC
Idling current| 1.7 A
Idling current when off| 0.09 mA
Consumption @ 14.4 VDC, MIN load impedance (Max Musical
Power)| 40 A
Remote IN| 6.5 ÷ 15 VDC (1 mA)
Remote OUT| 6.5 ÷ 15 VDC (150 mA)
ART – Automatic Remote Turn on/off
from OUTPUT BTL speakers
| 1.5 ÷ 7 VDC
AMPLIFIER STAGE
Distortion – THD @ 1 kHz, 4Ω, 70% Rated Power| 0.08 %
Damping factor @ 1 kHz, 4Ω, 2 VRMS| 200
Bandwidth @ -3 dB| 10 Hz ÷ 35 kHz
S/N ratio (A weighted @ 1 V Input)| 105 dBA
Pre-In sensitivity| 0.2 ÷ 5 VRMS
Speaker-In sensitivity| 0.8 ÷ 20 VRMS
Minimum load impedance
| @ 4Ch: 2Ω
@ 3Ch: 2Ω + 2Ω + 4Ω
@ 2Ch: 4Ω
Output power (RMS) @14.4 VDC, 1%
THD:
4Ch| 130 W x 4 (4Ω)
4Ch| 220 W x 4 (2Ω)
3Ch| 120 W x 2 (4Ω) + 480 W x 1 (4Ω)
3Ch| 220 W x 2 (2Ω) + 440 W x 1 (4Ω)
2Ch| 450 W x 2 (4Ω)
CEA SPECIFICATION
Output power @ 4Ω 1% THD+N, 14.4 V | 125 W x 4 Ch |
---|---|
SN ratio (ref. 1 W output) | 83 dBA |
INPUTS / OUTPUTS / FILTERS
Inputs| Pre-In / Speaker-In
Outputs| PRE OUT full range (Input A)
A Ch Filters:
| Full
Hi-pass: 50 ÷ 3.2k Hz @ 12 dB/Oct.
Lo-pass: 50 ÷ 3.2k Hz @ 12 dB/Oct.
B Ch Filters:
| Full
Hi-pass: 50 ÷ 3.2k Hz @ 12 dB/Oct.
Lo-pass: 50 ÷ 3.2k Hz @ 12 dB/Oct.
A Ch MONO IN (on/off)| Yes
B Ch MONO IN (on/off)| Yes
Bass Boost 50Hz (adjustable)| B Ch (0 ÷12) dB.
SUB Remote Volume Control (B Ch)| (-20 ÷ 6) dB
SIZE
Max size (mm/inch)| 264 x 155 x 47,5 / (10.39 x 6.10 x 1.87)
Weight (kg/lbs)| 2,12 / 4.67
POWER SUPPLY
Nominal power supply voltage / fuse| 11 ÷ 15 VDC / 2
x 25A
Pulse Operating voltage| 6.5 ÷ 17 VDC
Idling current| 2.2 A
Idling current when off| 0.04 mA
Consumption @ 14.4 VDC, MIN load impedance (Max Musical
Power)| 44 A
Remote IN| 6.5 ÷ 15 VDC (1 mA)
Remote OUT| 6.5 ÷ 15 VDC (150 mA)
ART – Automatic Remote Turn on/off
from OUTPUT BTL speakers
| 1.5 ÷ 7 VDC
AMPLIFIER STAGE
Distortion – THD @ 100 Hz , 4Ω, 70% Rated
Power| 0.02 %
Damping factor @ 1 kHz, 4Ω, 2 VRMS FRONT / REAR| 100
Damping factor @ 100 Hz, 4Ω, 2 VRMS SUB| 300
Bandwidth @ -3 dB FRONT / REAR; SUB| 10Hz ÷ 35kHz 10Hz ÷
500Hz
S/N ratio (A weighted @ 1 V Input)| 105 dBA
Pre-In sensitivity| 0.2 ÷ 5 VRMS
Speaker-In sensitivity| 0.8 ÷ 20 VRMS
Minimum load impedance| 5 Ch: 2Ω
3Ch: 4Ω + 4Ω + 2Ω
Output power (RMS) @14.4 VDC, 1%
THD:
5Ch| 75 W x 4 + 330 W x 1 (4Ω)
5Ch| 115 W x 4 + 550 W x 1 (2Ω)
3Ch| 230 W x 2 (4Ω) + 310 W x 1 (4Ω)
3Ch| 230 W x 2 (4Ω) + 550 W x 1 (2Ω)
CEA SPECIFICATION
Output power @ 4Ω 1% THD+N, 14.4 V | 75 W x 4 Ch + 300 W x 1 Ch |
---|---|
SN ratio (ref. 1 W output) | Front / Rear: 84 dBA |
SUB: 75 dBA
INPUTS / OUTPUTS / FILTERS
Inputs| Pre-In / Speaker-In
Front Ch Filters:| Full
Hi-pass: 50 ÷ 5k Hz @ 12 dB/Oct.
Rear Ch Filters:
| Full
Hi-pass: 50 ÷ 5k Hz @ 12 dB/Oct.
Band-pass: 50 ÷ 500 Hz (Hi) @ 12 dB/Oct.
50 ÷ 5 kHz (Lo) @ 12 dB/Oct.
SUB Ch Filters:| Lo-pass: 50 ÷ 500 Hz @ 24 dB/Oct.
Bass Boost 50Hz (adjustable)| (0 ÷12) dB
SUBSONIC (on/off)| 25 Hz @ 24 dB/Oct.
SUB Remote Volume Control| (-20 ÷ 6) dB
SIZE
Max size (mm/inch)| 294 x 155 x 47,5 / 11.57 x 6.10 x 1.87
Weight (kg/lbs)| 2,42 / 5.33
POWER SUPPLY
Nominal power supply voltage / fuse| 11 ÷ 15 VDC / 2
x 30A
Pulse Operating voltage| 6.5 ÷ 17 VDC
Idling current| 2.2 A
Idling current when off| 0.04 mA
Consumption @ 14.4 VDC, MIN load impedance (Max Musical
Power)| 54 A
Remote IN| 6.5 ÷ 15 VDC (1 mA)
Remote OUT| 6.5 ÷ 15 VDC (150 mA)
ART – Automatic Remote Turn on/off
from OUTPUT BTL speakers
| 1.5 ÷ 7 VDC
AMPLIFIER STAGE
Distortion – THD @ 1 kHz, 4Ω, 70% Rated Power A
Ch / B Ch / C Ch| 0.05 %
Damping factor @ 1 kHz, 4Ω, 2 VRMS A Ch/B Ch
/C Ch
| 100
400
Bandwidth @ -3 dB A Ch / B Ch / C Ch| 10Hz ÷ 42 kHz
S/N ratio (A weighted @ 1 V Input)| 102 dBA
Pre-In sensitivity| 0.32 ÷ 8 VRMS
Speaker-In sensitivity| 1.6 ÷ 40 VRMS
Minimum load impedance| 6 Ch: 2Ω
3Ch: 4Ω + 4Ω + 2Ω
Output power (RMS) @14.4 VDC, 1%
THD:
6Ch| 85 W x 4 + 110 W x 2 (4Ω)
6Ch| 140 W x 4 + 185 W x 2 (2Ω)
6Ch| 75 W x 4 (4Ω) + 340 W x 2 (1Ω)
6Ch| 130 W x 4 (2Ω) + 300 W x 2 (1Ω)
5Ch| 85 W x 4 + 370 W x 1 (4Ω)
5Ch| 130 W x 4 + 600 W x 1 (2Ω)
3Ch| 280 W x 2 (4Ω) + 370 W x 1 (4Ω)
3Ch| 260 W x 2 (4Ω) + 600 W x 1 (2Ω)
CEA SPECIFICATION
Output power @ 4Ω 1% THD+N, 14.4 V | 75 W x 4 Ch + 85 W x 2 Ch |
---|---|
SN ratio (ref. 1 W output) | A Ch, B Ch: 84 dBA |
C Ch: 84 dBA
INPUTS / OUTPUTS / FILTERS
Inputs| Pre-In / Speaker-In
A Ch Filters:| Full
Hi-pass: 50 ÷ 5k Hz @ 12 dB/Oct.
B Ch Filters:
| Full
Hi-pass: 50 ÷ 700 Hz @ 12 dB/Oct.
Band-pass: 50 ÷ 700 Hz (Hi) @ 12 dB/Oct.
50 ÷ 5 kHz (Lo) @ 12 dB/Oct.
C Ch Filters:
| Full
Hi-pass: 50 ÷ 700 Hz @ 12 dB/Oct.
Lo-pass: 50 ÷ 700 Hz @ 12 dB/Oct
A Ch MONO (on/off)| YES
B Ch MONO (on/off)| YES
C Ch MONO (on/off)| YES.
SUB Remote Volume Control| (-20 ÷ 6) dB
SIZE
Max size (mm/inch)| 314 x 155 x 47.5 / 12.36 x 6.10 x 1.87
Weight (kg/lbs)| 2,52 / 5.55
FAQ
- Q: What should I do if any of the components are missing from the packaging?
- A: Contact customer support immediately to report the missing items and request assistance.
- Q: How do I know which cables to use for connecting the subwoofer?
- A: Refer to the user manual for detailed instructions on cable connections and their designated usage.
- Q: How can I troubleshoot if the subwoofer is not functioning correctly?
- A: Check the connections, power source, and settings following the troubleshooting section in the manual. If issues persist, contact customer support for further assistance.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>