scheppach SprayVac20FB Spray Extraction Cleaner Instruction Manual

: June 1, 2024
: Scheppach

scheppach SprayVac20FB Spray Extraction Cleaner

Specifications:

Model: SprayVac20FB
Power Supply: 220-240 V~ / 50/60 Hz
Power Consumption: 1600 W
Vacuum Pressure: 20000 Pa
Bar Pressure: Approximately 3 bar
Water Flow Rate: 0.5 l/min
Protection Class: II IPX4
Tank Capacity: 20 l
Clean Water Tank Capacity: 3.5 l
Weight: 7.5 kg

Product Usage Instructions

Unpacking and Assembly:
Follow the provided instructions to unpack the product and assemble the machine head with the filter basket.

Safety Precautions:
Read the user manual carefully to reduce the risk of injury.
This spray extraction cleaner is double insulated and does not need to be connected to an earthed socket.

Operating the Machine:

Ensure the machine is properly assembled and all components are in place.
Connect the power supply to the designated socket.
Fill the clean water tank with the recommended amount of water and cleaning solution.
Switch on the machine and start cleaning the desired area by spraying and vacuuming simultaneously.

Cleaning and Maintenance:
After each use, empty and clean both the dirty water tank and the filter to prevent clogging and maintain optimal performance.
Regularly check for any blockages in the hoses.

Storage:
Ensure the machine is completely dry before storing it in a cool, dry place. Store all accessories in their designated compartments to prevent loss or damage.

Frequently Asked Questions (FAQ):

Q: How often should I clean the filters?
A: It is recommended to clean the filters after every use to maintain the efficiency of the spray extraction cleaner.

Q: Can I use this product on delicate fabrics?
A: While the product can be used on various surfaces, it is advisable to test it on a small inconspicuous area first,especially on delicate fabrics, to ensure compatibility.

Explanation of the symbols on the device
Symbols are used in this manual to draw your attention to potential hazards. The safety symbols and the accompanying explanations must be fully understood. The warnings themselves will not rectify a hazard and cannot replace proper accident prevention measures.

$scheppach-SprayVac20FB-Spray-Extraction-Cleaner-FIG- $21$$

Introduction

Manufacturer:
Scheppach GmbH Günzburger Straße 69 D-89335 Ichenhausen
Dear Customer
We hope your new tool brings you much enjoyment and success.

Note:
In accordance with the applicable product liability laws, the manufacturer of this device assumes no liability for damage to the device or caused by the device arising from:

Improper handling,
Non-compliance with the operating manual,
Repairs carried out by third parties, unauthorised specialists.
Installing and replacing non-original spare parts
Application other than specified
Failure of the electrical system in the event of the electrical regulations and VDE provisions 0100, DIN 13 / VDE0113 not being observed

Please consider:
Read through the complete text in the operating manu-al before installing and commissioning the device. The operating manual is intended to help the user to become familiar with the machine and take advantage of its application possibilities in accordance with the recommendations.
The operating manual includes important instructions for safe, proper and economic operation of the device, for avoiding danger, for minimising repair costs and downtimes, and for increasing the reliability and ex-tending the service life of the device.

In addition to the safety instructions in this operating manual, you must also observe the regulations appli-cable to the operation of the device in your country. Keep the operating manual package with the machine at all times and store it in a plastic cover to protect it from dirt and moisture. They must be read and careful-ly observed by all operating personnel before starting the work.
The device may only be used by personnel who have been trained to use it and who have been instructed with respect to the associated hazards.

The required minimum age must be observed.
In addition to the safety instructions in this operating manual and the separate regulations of your country, the generally recognised technical rules relating to the operation of such machines must also be observed. We accept no liability for accidents or damage that occur due to a failure to observe this manual and the safety instructions.

Device description

FIG 1

$scheppach-SprayVac20FB-Spray-Extraction-Cleaner-FIG- $1$$

FIG 2

$scheppach-SprayVac20FB-Spray-Extraction-Cleaner-FIG- $2$$

FIG 3

FIG 4

FIG 5

FIG 6

FIG 7

FIG 8

FIG 9

FIG 10

FIG 11

FIG 12

FIG 13

FIG 14

FIG 15

FIG 16

FIG 17

FIG 18

FIG 19

FIG 20

Stainless steel container
- a. Water tank detent
Suction connection
Machine head with filter cage
- a. Filter cage
- b. Cover cap
- c. Safety float valve
- d. Mains connection cable
Water duct connection from the suction pipe
On/off switch
Carrying handle
Water channel connection from the water tank
Locking hooks
Water tank
Water tank level indicator
Wheel
Castors
Caster mounting base
Cable holder
a. Connection for blower function
Filter cleaning function connection
Water channel on the water tank
Water tank cover
Water tank carrying handle
Lever for spray function
Handle
a. Air regulation
Suction pipe
Extraction hose
Suction connection
Water channel on the suction hose
Extension pipe
Washing nozzle with hard surface attachment
Washing nozzle for upholstery cleaning
Floor nozzle
Joint nozzle
Screws
Folded filter
Foam filter (not included in scope of delivery)
Foam filter
Fabric filter bag
Water spray nozzle
Upholstery nozzle

Scope of delivery

(fig. 2)

Washing vacuum …………………………………….1x
Water tank ………………………………………………1x
Wheel …………………………………………………….2x
Castors …………………………………………………..2x
Screws …………………………………………………..4x
Extraction hose ……………………………………….1x
Extension pipe ………………………………………..2x
Washing nozzle with hard surface insert ……1x
Washing nozzle for upholstery cleaning …….1x
Floor nozzle ……………………………………………1x
Joint nozzle …………………………………………….1x
Foam filter ………………………………………………1x
Fabric filter bag ……………………………………….2x
Folded filter …………………………………………….1x
Upholstery nozzle ……………………………………1x

Proper use
The device is intended as a Spray extraction cleaner for cleaning carpets.
The device can also be used as a wet and dry vacuum cleaner in domestic areas such as in the household, hobby room, car or garage, or for extracting water. This device is not suitable for commercial use. Com-mercial use will invalidate the warranty.

The vacuuming of flammable, explosive or hazardous substances is forbidden.
The machine may only be used in the intended manner. Any use beyond this is improper. The user/operator, not the manufacturer, is responsible for damages or inju-ries of any type resulting from this.
An element of the intended use is also the observance of the safety instructions, as well as the assembly in-structions and operating information in the operating manual.
Persons who operate and maintain the machine must be familiar with it and must be informed about potential dangers.
In addition, the applicable accident prevention regula-tions must be strictly observed.
Other general occupational health and safety-related rules and regulations must be observed.
The liability of the manufacturer and resulting damages are excluded in the event of modifications of the ma-chine.

The machine may only be operated with original parts and original accessories from the manufacturer.
The safety, operating and maintenance specifications of the manufacturer, as well as the dimensions speci-fied in the technical data, must be observed.
Please observe that our equipment was not designed with the intention of use for commercial or industrial purposes. We assume no guarantee if the equipment is used in commercial or industrial applications, or for equivalent work.
The device is intended for use by adults. Children over the age of 16 may use the tool except under supervi-sion. The manufacturer is not liable for damage caused by an improper use or incorrect operation of this de-vice.

General safety information

DANGER!

Connect the device to alternating current only. The voltage must match the type plate on the device.
Never touch the mains plug and socket with wet hands.
Do not pull the mains plug out of the socket by pull-ing on the connection cable.
Check the connection cable with the mains plug for damage before each use. Immediately replace a damaged connection cable by an authorised cus-tomer service / qualified electrician in order to avoid hazards.
To avoid electrical accidents, we recommend us-ing sockets with an upstream residual current cir-cuit breaker (max. 30 mA nominal tripping current).
Pull out the mains plug before carrying out any cleaning and maintenance work!
All repair work, also to any electrical components, must be carried out by an authorised customer ser-vice centre.

Attention!

This device is not designed to be operated by per-sons with impaired physical, sensory or mental ca-pabilities, or who have insufficient experience and/or insufficient knowledge unless they are being su-pervised by a person who is responsible for their safety or they are receiving instruction about how this device is to be used.
Children may only use the device if they are over 8 years old and if they are supervised by a person responsible for their safety or if they have received instructions from them on how to use the device and have understood the resultant hazards.
Children may not play with the device.
Children should be supervised in order to ensure that they do not play with the device.
Cleaning and user maintenance must not be carried out by children unsupervised.
Keep packaging material away from children, there is a risk of suffocation!
It is recommended to switch off the device after each usage and before maintenance work.
Risk of fire. Do not vacuum any burning or glowing particles.
Do not operate the device in explosive environ-ments.
If foam forms or liquid escapes, switch off the device immediately or pull out the mains plug!
Do not use abrasive cleaners, glass or all-purpose cleaners! Do not immerse the device in water.

Certain substances can form explosive vapours or mixtures when they are swirled with the suction air! Never vacuum the following substances:

Explosive or flammable gases, liquids and dusts (reactive dusts)
Reactive metal dusts (such as aluminum, magnesi-um, zinc) combined with strongly alkaline and acidic cleaning agents
Undiluted strong acids and alkalis
Organic solvents (such as gasoline, paint thinner,acetone, heating oil).

In addition, these substances can corrode the materi-als used on the device.

WARNING!
This power tool generates an electromagnetic field during operation. This field can impair active or pas-sive medical implants under certain conditions. In or-der to prevent the risk of serious or deadly injuries, we recommend that persons with medical implants consult with their physician and the manufacturer of the medical implant prior to operating the power tool.

Residual risks
The machine has been built according to the state-of-the-art and the recognised technical safety require-ments. However, individual residual risks can arise during operation.

Health hazard due to electrical power, with the use of improper electrical connection cables.
Furthermore, despite all precautions having been met, some non-obvious residual risks may still remain.
Residual risks can be minimised if the “Safety infor-mation” and the “Proper use” together with the oper-ating manual as a whole are observed.
Avoid accidental starting of the machine: the op-erating button may not be pressed when inserting the plug in an outlet. Use the tool attachment that is recommended in this operating manual. This is how to ensure that your machine provides optimum performance.
Keep your hands away from the work area, when the machine is in operation.

Technical data

Mains voltage 220-240 V~ /50/60 Hz
Power 1600 W
Suction capacity 20000 Pa
Spray pressure approx . 3 bar
Output 0.5 l/min
Protection class II
Protection category IPX4
Dirty water tank capacity 20 L
Water tank capacity 3.5 L
Weight 7,5 kg

Technical changes reserved!

Unpacking

Open the packaging and carefully remove the device.
Remove the packaging material, as well as the packaging and transport safety devices (if present).
Check whether the scope of delivery is complete.
Check the device and accessory parts for transport damage. In the event of complaints the carrier must be informed immediately. Later claims will not be recognised.
If possible, keep the packaging until the expiry of the warranty period.
Familiarise yourself with the product by means of the operating instructions before using for the first time.
With accessories as well as wearing parts and replacement parts use only original parts. Replacement parts can be obtained from your dealer.
When ordering please provide our article number as well as type and year of manufacture for your equipment.

WARNING!
The device and the packaging material are not children’s toys! Do not let children play with plastic bags, films or small parts! There is a danger of choking or suffocating!

Assembly / Before commissioning

ATTENTION!
Prior to use, ensure that the device has been correctly and fully assembled.

Unpacking (Fig. 1, 2)

Release the locking hooks (8) and remove the machine head with filter cage (3). The accessories are located inside the stainless steel container (1). Only the extension pipes (25) are located outside the stainless steel container (1) in the packaging. Remove all of the accessories from the stainless steel container (1).

Installation of the roller mounts (11 + 12) (Fig. 3)

Turn the stainless steel container (1) upside down.
(The machine head with filter cage (3) must be removed.)
Slide the wheels (11) into the recesses provided on the caster mounting base (13) and screw them in place with the screws (30).

Installation of the castors (12) (Fig. 3)

Press the two deflection rollers (12) into the holes provided in the roller mounts (12a).

Installing the machine head with filter cage (3) (Fig. 8)

Place the machine head with filter cage (3) on the stainless steel container (1).
Secure the machine head (3) with the locking hooks (8). When installing the machine head with filter cage (3), ensure that the locking hooks (8) latch into place correctly. The water channel connection (4) must be above the vacuum connection (2).

Installing the filter (33) (Fig. 5, 6)
Never use the device without filter! Always ensure that the filters are correctly fitted.

Installing the foam filter (33)

For wet vacuuming, open and remove the filter cage (3a) by turning it anti-clockwise (Fig. 6).
Pull off the clipped cover cap (3b) with a screwdriver (not included in the scope of delivery), pull the foam filter (33) over the filter cage with safety float valve (3c) and refit the cover cap (3b) (Fig. 5).
Now reinsert the filter cage by turning it clockwise (Fig. 6).
To avoid tearing the foam filter (33),
- only insert a dry filter
- knock the edge of the filter over a little to insert it and then roll it back again.

Fit the folded filter (31) and foam filter (32) (not included in the scope of delivery)

Open and remove the filter cage (3a) by turning it anti-clockwise (Fig. 6).
Insert the hepa filter (31) or foam filter (32) and replace the filter cage by turning it clockwise (Fig. 6).

Installing the fabric filter bag (34) (fig. 7)
It is recommended to use an additional fabric filter bag (34) when vacuuming fine, dry dirt.

Slide the fabric filter bag (34) over the suction opening in the stainless steel container (1).
The fabric filter bag (34) is only suitable for dry vacuuming. The fabric filter bag (34) makes it easier to dispose of the dust collected.

Filling the water tank (Fig. 15)
The water tank (9) can be removed for filling or filled directly at the device.

Fill the water tank (9) through the opening (17) with clear water (max. 3 l). Pay attention to the markings on the container (10)
If the water tank is heavily contaminated or stained, add a little cleaning agent, e.g. carpet and upholstery cleaner.

Installing the water tank (Fig. 4)

Take the water tank (9) by the handle (18) and place it in the openings of the caster mounting base (13).
Now press the water tank (9) against the detent (1a) until it locks into place.

Installing the suction hose (Fig. 10)

Connect the suction hose (22) to the corresponding port, depending on the desired use, on the wet and dry vacuum cleaner.

Vacuuming (Fig. 10)

Connect the suction hose (22) to the suction hose connection (2).
To do so, slide the end of the suction hose (23) with the two nipples into the suction hose port (2).
Insert the two nipples into the recesses. In the end position, turn the suction hose (22) in a clockwise direction.

Blowing (Fig. 11)

Connect the suction hose (22) to the blast function connection port (14a).
Slide the end of the suction hose (23) with the two nipples into the blast function connection port (14a).
Insert the two nipples into the recesses. In the end position, turn the suction hose (22) in a clockwise direction.

Fitting plastic extension tubes (25), suction hose (22) and nozzles (26, 27, 28, 29, 36) (Fig. 10, 13)

Connect the plastic extension tubes (25) together.
Connect the assembled plastic extension tubes with the bent end of the suction hose (21). 3. Fit one of the corresponding nozzles (26, 27, 28, 29, 36) to the end of the plastic tube (25) or the curved end of the suction pipe (21).

Fitting the water channels (16, 24, 25) (fig. 12, 13)

To do this, push the end of the respective water channel (16, 24) with the two nipples into the water channel connection (4, 7).
Insert the two nipples into the recesses. In the end position, turn the water channel (16, 24) in a clockwise direction. (Fig. 12, 13).
Slide the end of the water channel from the end of the plastic tube (25) or the curved end of the suction pipe (21) with the two nipples into the recesses at one of the corresponding nozzles (26,27, 28, 29).
In the end position, turn the water channel in a clockwise direction. (Fig. 13).

Start up

Warning! Switch the device off if liquid or foam emerges with the exhaust air during wet vacuuming.

Switching on/off (fig. 11)

Connect the mains plug of the device.
Press the on/off switch (5):
- Switch setting 0: Off
- Switch setting I: On
- Switch setting II: On + spray function

Switching on the washing function (Fig. 19)

Switch on the device with the spray function (see Switching on/off)
Press the pump switch (19)

Air regulation (Fig. 19)
The device has an air control (20a) with which the suction capacity can be adjusted.

To do this, move the air regulation switch (20a) on the handle (20) until the desired air regulation is reached.

Wet vacuuming

Use the foam filter (33) for wet vacuuming.
Ensure that the foam filter (33) is correctly fitted.
If the stainless steel container (1) is full, the safety float valve (3c) closes the suction port and suction operation is interrupted.

Attention!
The device is not suitable for vacuuming flammable liquids. For wet vacuuming, use the only the foam filter (3) provided

Suction washing (Fig. 18)
Only use the washing nozzle with hard surface attachment (26) or the washing nozzle for upholstery cleaning (27) for vacuum washing.
Use the foam filter (33) for wet vacuuming. Ensure that it is correctly fitted.

Fill the water tank (9).
Pull (do not push!) the nozzle (26, 27) in stripes over the carpet / upholstery. Allow the stripes to overlap slightly to ensure thorough cleaning.
Press the spray function lever (19) on the handle part to switch on the spray function.
Empty the stainless steel container (1) immediately after vacuuming, as it is not designed to store liquids.

Electrical connection

The electrical motor installed is connected and ready for operation. The connection complies with the applicable VDE and DIN provisions.
The customer‘s mains connection as well as the extension cable used must also comply with these regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is often damaged.

This may have the following causes:

Pressure points, where connection cables are passed through windows or doors.
Kinks where the connection cable has been improperly fastened or routed.
Places where the connection cables have been cut due to being driven over.
Insulation damage due to being ripped out of the wall outlet.
Cracks due to the insulation ageing.

Such damaged electrical connection cables must not be used and are life- threatening due to the insulation damage.
Check the electrical connection cables for damage regularly. Ensure that the connection cables are disconnected from electrical power when checking for damage.
Electrical connection cables must comply with the applicable VDE and DIN provisions. Only use connection cables of the same designation.
The printing of the type designation on the connection cable is mandatory.

Connection type Y
If the mains connection cable of this device is damaged,it must be replaced by the manufacturer, their service department or a similarly qualified person to avoid dangers.

For single-phase AC motors, we recommend a fuse rating of C 16A or K 16A for machines with a high starting current (from 3000 watts)!

Cleaning

WARNING!
Pull out the mains plug before carrying out any adjustments, maintenance or repair work!

Keep protective devices, air vents and the motor housing as free of dust and dirt as possible. Rub the device clean with a clean cloth or blow it off with compressed air at low pressure.
We recommend that you clean the device directly after every use.
Clean the device at regular intervals using a damp cloth and a little soft soap. Do not use any cleaning products or solvents; they could attack the plastic parts of the device. Make sure that no water can penetrate the device interior. Water entering a power tool will increase the risk of electric shock.
Remove the water tank and the motor head and empty the water tank (9) and the stainless steel container (1) after each operation.
Wash out the foam filters (32, 33) with lukewarm water and soap and let them air dry.
Rinse the water channels (16, 24, 25) with clear water and empty them afterwards.
Empty fabric filter bag when full.
Wash out the fabric filter bag (34) with lukewarm water and soap and let them air dry.
Clean the device only with a soft brush or a damp cloth.

Filter cleaning function (Fig. 20)
When vacuuming fine dust, the Hepa filter (31) may become clogged and the suction power noticeably reduced.

To clean the Hepa filter (31), proceed as follows.

Switch the ON/OFF switch (5) to (I).
Now put the suction tube (21) on the connection of the filter cleaning function (15) and press it down.
The Hepa filter (31) is blown free by the resulting negative pressure.
Repeat the process if necessary.

Storage

Store the device and its accessories in a dark, dry and frost-free place that is inaccessible to children. The optimum storage temperature lies between 5 and 30 ˚C. Store the power tool in its original packaging. Cover the power tool to protect it from dust or moisture. Store the operating manual with the power tool.

Wrap the mains connection cable (3d) around the cable holder (14).
On the upper side of the caster mounting base (13) there are two recesses to which the extension pipes (25) can be attached for storage.
On the top of the motor head (3) there are four recesses to which the washing nozzle with hard surface attachment (26), the washing nozzle with upholstery cleaning (27), the floor nozzle (28) and the joint nozzle (29) can be attached for storage.

Maintenance

The device has no further internal parts that require maintenance.

Service information
With this product, it is necessary to note that the following parts are subject to natural or usage-related wear, or that the following parts are required as consumables.
Wearing parts*: Foam filter, HEPA filter, fabric filter bag may not be included in the scope of supply!

Connections and repairs
Connections and repair work on the electrical equipment may only be carried out by electricians.

Please provide the following information in the event of any queries:

Type of current for the motor
Data of machine type plate
Data of motor type plate

Spare parts and accessories can be obtained from our service centre. To do this, scan the QR code on the front page.

Disposal and recycling

Notes for packaging
The packaging materials are recyclable.
Please dispose of packaging in an environmentally friendly manner.

Notes on the electrical and electronic equipment act [ElektroG] Waste electrical and electronic equipment does not belong in household waste, but must be collected and disposed of separately!

Used batteries or rechargeable batteries that are not installed permanently in the old appliance must be removed non-destructively before disposal. Their disposal is regulated by the battery law.
Owners or users of electrical and electronic devices are legally obliged to return them after use.
The end user is responsible for deleting their personal data from the old device being disposed of!
The symbol of the crossed-out dustbin means tha waste electrical and electronic equipment must not be disposed of with household waste.
Waste electrical and electronic equipment can be handed in free of charge at the following places:
- Public disposal or collection points (e.g. municipal works yards)
- Points of sale of electrical appliances (stationary and online), provided that dealers are obliged to take them back or offer to do so voluntarily.
- Up to three waste electrical devices per type of device, with an edge length of no more than 25 centimetres, can be returned free of charge to the manufacturer without prior purchase of a new device from the manufacturer or taken to another authorised collection point in your vicinity.
- Further supplementary take-back conditions of the manufacturers and distributors can be obtained from the respective customer service.
If the manufacturer delivers a new electrical appliance to a private household, the manufacturer can arrange for the free collection of the old electrical appliance upon request from the end user. Please contact the manufacturer’s customer service for this.
These statements only apply to devices installed and sold in the countries of the European Union and which are subject to the European Directive 2012/19/EU. In countries outside the European Union,different regulations may apply to the disposal of waste electrical and electronic equipment.

Troubleshooting

The following table shows fault symptoms and describes remedial measures in the event of your machine failing to work properly. If you cannot localise and rectify the problem with this, please contact your service workshop.

Fault	Possible cause	Remedy

Motor does not run

| Check whether the plug is plugged in.| Plug the mains plug back in to the socket.
Check whether there is power to the

socket.

| Check socket, mains connection cable, lead, plug and fuse, if necessary, have repaired by an electrician
Check whether the vacuum cleaner on/off switch is switched on| Switch the on/off switch on.
On/off switch defective|

Repair by customer service department

Carbon brushes worn
Engine defective

Low or lacking suction capacity

| Air regulation on the handle open| Close air regulation
Vacuum hose or nozzles clogged| Switch off the hoover to clear blockages and

obstructions.

Container open| Close container
Container or dust bag full| Empty container / replace dust bag
Filter full or clogged| Empty, clean or replace filter
Float in filter cage does not move| Clear the float
Float does not switch

off the device

| Float in filter cage does not move| Clear the float
Dust or dirt is blown out of the device| Filter absent or not fitted correctly| Insert absent filter or check correct fit of filter

Water channel leaking

| Water channels not connected properly| Connect and lock the water channels correctly
Sealing ring missing or porous| Insert / replace sealing ring

Low or no spraying performance

| Water channel clogged| Clean water channel
Water channel kinked| Avoid kinking the water channel
Spray pump defective| Repair by customer service department

Only air coming out of the spray nozzle

| Water tank empty| Fill up the water tank
Water channel is not connected to the water tank| Fit the water channel correctly

PARTS

$scheppach-SprayVac20FB-Spray-Extraction-Cleaner-FIG- $22$$

EC Declaration of Conformity
hereby declares the following conformity under the EU Directive and standards for the following article

Standard references:
EN 62233:2008; EN 60335-2-10:2003+A1:2008; EN 60335-2-2:2010+A11:2012+A1:2013;
EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A2:2019+A14:2019+A15:2021; EN IEC 55014-1:2021;
EN IEC 55014-2:2021; EN IEC 61000-3-2:2019+A1:2021; EN 61000-3-3:2013+A1:2019

This declaration of conformity is issued under the sole responsibility of the manufacturer.

The object of the declaration described above fulfils the regulations of the directive 2011/65/EU of the European Parliament and Council from 8th June 2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Warranty

Apparent defects must be notified within 8 days from the receipt of the goods. Otherwise, the buyerís rights of claim due to such defects are invalidated. We guarantee for our machines in case of proper treatment for the time of the statutory warranty period from delivery in such a way that we replace any machine part free of charge which provably becomes unusable due to faulty material or defects of fabrication within such period of time. With respect to parts not manufactured by us we only warrant insofar as we are entitled to warranty claims against the upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer. The cancellation of sale or the reduction of purchase price as well as any other claims for damages shall be excluded.

www.scheppach.com