PHILIPS TAH8507 Wireless Headphone User Manual

TAH8507 Wireless Headphone
User Manual Register your product and get support at www.philips.com/support

Important safety instructions

Hearing safety

Danger

• To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.
  Be sure to observe the following guidelines when using your headphones.

• Listen to reasonable volumes for reasonable periods of time.

• Be careful not to adjust the volume continuously upwards as your hearing adapts.

• Do not turn up the volume so high that you can’t hear what’s around you.

• You should use caution or temporarily discontinue use in potentially hazardous situations.

• Excessive sound pressure from earphones and headphones can cause hearing loss.

• Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.

• For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

General information
To avoid damage or malfunction:

Caution

• Do not expose headphones to excessive heat.

• Do not drop your headphones.

• Headphones shall not be exposed to dripping or splashing. (Refer to the IP rating of a specific product)

• Do not allow your headphones to be submerged in water.

• Do not charge your headphones when the connector or socket is wet.

• Do not use any cleaning agents containing
  alcohol, ammonia, benzene, or abrasives.

• If cleaning is required, use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.

• The integrated battery shall not be exposed to excessive heat such as sunshine, fire, or the like.

• Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.

• To achieve the specific IP rating, the charging slot cover must be closed.

• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting a battery, can result in an explosion.

• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.

• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

• Replacement of a battery with an incorrect type risks severely damaging the headphones and the battery (for example, in the case of some lithium battery types).

Operating and storage temperatures and humidity

• Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) with up to 90% relative humidity.
• Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) with up to 90% relative humidity.
• Battery life may be shorter in high or low-temperature conditions.

Your Bluetooth over-ear headphones

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support.
With these Philips over-ear headphones, you can:

• Enjoy convenient wireless hands-free calls
• Enjoy and control music wirelessly
• Switch between calls and music
• Enjoy noise cancellation

What’s in the box

|
---|---

Other devices
A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible with the headphones (see ‘Technical data’ on page 9).

Overview of your Bluetooth wireless headphones

Get started

Charge the battery
Note

• Before you use your headphones for the first time, charge the battery for 2 hours for optimum battery capacity and lifetime.
• Use only the original USB charging cable to avoid any damage.
• Finish your call before charging the headphones, as connecting the headphones for charging will power the headphones off. Connect the supplied USB charging cable to:
• The USB type C charging slot on the headphones and;
• The charger/USB port of a computer.
  LED turns white during charging and turns off when the headphones in fully charged.

Connect the supplied USB charging cable to:

• The USB type C charging slot on the headphones and;
• The charger/USB port of a computer.
  LED turns white during charging and turns off when the headphones in fully charged.

Tip

• Normally, a full charge takes 2 hours.

Pair the headphones with your mobile phone

Before you use the headphones with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and the mobile phone. The headphones store the last 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.

1. Make sure that the headphones are fully charged and turned off.

2. Press and hold for 5 seconds until the blue and white LED flashes alternately
   The headphones remain in pairing mode for 5 minutes

3. Make sure that the mobile phone is turned on and its Bluetooth feature is activated.

4. Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone.

The following example shows you how to pair the headphones with your mobile phone.
Activate the Bluetooth feature of your mobile phone, select Philips TAH8507

Use your headphones

Connect the headphones to your Bluetooth device

1. Turn on your mobile phone/Bluetooth device.
2. Press and hold the on/off button to turn the headphones on.
   The white LED will turn on in 2 seconds
   The headphones are reconnected to the last connected mobile phone/Bluetooth device and the dongle automatically

Tip

• If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone/Bluetooth device manually.

Note

• If the headphones fail to connect to the last connected Bluetooth device within range in 20 seconds, it will change to connectable mode, then will switch off automatically if it’s still not connected to any Bluetooth device 5 minutes later.

Wired connection
You can also use the headphones with the audio cable provided. Connect the supplied audio cable to the headphones and external audio device.

Multi-point connection

Pairing

• Pairing the headphones with two devices, e.g. mobile phones and notebooks Switch between devices
• Music can only be played from one device at a time. Your second device will be reserved for phone calls
• Pause the audio from one device to start playing audio from your other device

Note

• Receiving a call on device two will pause playback on device one. The call will be routed automatically to your headphones.
• Ending the call will resume playback from device one automatically.

Connect the headphone to your computer

1. Plug the dongle into your computer with USBC or USBA with a converter.
   

2. Turn on the headphones, your computer and headphones will be connected automatically

Tip

• Dongle will have solid blue led when connected.

Note
To reconnect:
a) Plug out and plug in your dongle from the computer and wait for it to auto- connect.
Or
b) With the dongle in the computer USB port, press the button on the dongle once to initiate a connection with your device.

Manage your calls and music

On/off

Task| Button| Operation
Turn the headphones on| Power button| Press and hold for 2 seconds
Turn the headphones off| Power button| Press and hold for 2 seconds The white LED is on and fades out
Music control
Play or pause music| TouchPad| Tap 2 times
Adjust volume| TouchPad| Swipe up/Swipe down
Next track| TouchPad| Swipe front
Previous track| TouchPad| Swipe back
Call control
Pick up a call| TouchPad| Tap 2 times
Reject/hang up a call| TouchPad| Touch 1
second
Answer new call during a call| TouchPad| Tap 2 times
Reject a new call during a call| TouchPad| Touch 1 second
Switch call when answered two
calls| TouchPad| Tap 2 times
ANC control
ANC ON⁄Awareness mode⁄ANC OFF| ANC Mode button| Press once
Awareness mode| ANC Mode Button| Press until hear “Awareness on”
Quick conversation| TouchPad| Palm over the Right ear cup
Smartphone voice assist function (e.g. Google app, Siri)
Wake up smartphone voice  assist function| Voice Assistant Button| Press once

Note

• Please refer to the operating instructions of the smartphone.

Other headphones indicator status

alternately
The headphones are on but not connected to a Bluetooth device| The blue LED flashes once every 7 seconds.
If no connection can be made, the headphones will turn themselves off  within 5 minutes
Low battery level| The white LED blinks slowly until it is out of power
The battery is fully charged| White LED is off
Headphones are in the phone call| The red busy LED will blink

App download

Scan the QR code/press the ‘Download’ button or search ‘Philips Headphones’ in Apple App Store or Google Play to download App.

https://apps.tpvava.com/headphoneall

The Philips Headphones App puts you in charge of the music you’ve listened to.
You can customize the sound so your music and calling experience always best suits your needs.

Technical data

• Music play time (ANC off): up to 55 hours

• Music play time (ANC on): up to 45 hours

• Charging time: 2 hours

• Rechargeable lithium-ion battery (800 mAh)

• Bluetooth version: 5.0

• Compatible Bluetooth profiles:
  • HFP (Hands-Free Profile)
  • A2DP (Advanced Audio Distribution Profile)
  • AVRCP (Audio Video Remote Control Profile)

• Frequency range: 2.402-2.480GHz

• Transmitter power: < 10 dBm

• Operating range: Up to 10 meters (33 feet)

• Digital echo & noise reduction

• Auto power off

• Type -C-USB port for charging

• Supports AAC and SBC

Note

• Specifications are subject to change without notice.
• Battery life of playtime is approximate and may vary depending on application condition.

Notice

Declaration of conformity
Hereby, MMD Hong Kong Holding Limited declares that the product is in compliance with the essential requirements and other relevant provisions of RED
Directive 2014/53/EU and UK Radio
Equipment Regulations SI 2017 No 1206.
You can find the Declaration of Conformity on www.philips.com/support.

Disposal of your old product and battery
Your product is designed and manufactured with high-quality materials and components which can be recycled and reused.
This symbol on a product means that the product is covered by European Directive 2012/19/EU.
This symbol means that the product contains a built-in rechargeable battery covered by European Directive
2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service center to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery
If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the headphones.

• Make sure the headphones is disconnected from the charging case before removing the battery.

Compliance with EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials that can be recycled and reused if disassembled by a specialized company. Please observe the  local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Notice of compliance
The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC rules
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,  which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between equipment and receiver
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Caution:
The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Canada:
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement:
This equipment complies with Canada’s radiation exposure limits set forth for uncontrolled environments.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Trademarks

Bluetooth
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Top Victory Investment Limited is under license.  Other trademarks and trade names are those of their respective owners.
Siri
Siri is a trademark of Apple Inc., registered in the U.S. and other countries.
Google
Google is a trademark of Google LLC.
The Google Assistant is not available in certain languages and countries.

Frequently asked questions

My Bluetooth headphones do not turn on.
The battery level is low. Charge the headphones.
I cannot pair my Bluetooth headphones with my Bluetooth device.
The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the headphones.
How to reset pairing.
Press and hold both Power + ANC buttons for 3 seconds, and the LED lights up blue, and then blue and white LEDs flash alternately.
I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward).
Make sure the Bluetooth audio source supports AVRCP (see ‘Technical data’ on page 8).
The volume level of the headphones is too low.
Some Bluetooth devices cannot link the volume level with the headphones through volume sync. In this case, you have to adjust the volume on your Bluetooth device independently to achieve an appropriate volume level.

The Bluetooth device cannot find the headphones.

• The headphones may be connected to a previously paired device. Turn off the connected device or move it out of range.
• Pairing may have been reset or the headphones have been previously paired with another device. Pair the headphones with the Bluetooth device again as described in the user manual. (see ‘Pair the headphones with your Bluetooth device for the first time on page 6).

My Bluetooth headphones are connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone. Select to listen to music through the headphones.
The audio quality is poor and crackling noise can be heard.

• The Bluetooth device is out of range.
  Reduce the distance between your
  headphones and Bluetooth device,
  or remove obstacles between them.

• Charge your headphones.

Reset the dongle pairing.

• Plug in the dongle to your computer.
• In the dongle, press and hold the “Pair” button for 2 seconds until the blue and white LED flashes alternately.
• In the headphones, press and hold for 5 seconds until the blue and white

LED flashes alternately.

• Soon, the dongle and the headphones will pair automatically.
• When successfully paired, the LED will turn blue.

For further support, visit www.philips.com/support.

2021©MMD Hong Kong Holding Limited. All rights reserved.
Specifications are subject to change without notice.
Philips and the Philips Shield Emblem have registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. All other company and product names may be trademarks of their respective companies with which they are associated. UM_TAH8507_00_EN_V1.0
Model: TAH8507HS

References

• Philips Customer Service Support - Home | Philips

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>