milwaukee M18 FSAG125XB Cordless Angle Grinder User Manual
- June 1, 2024
- Milwaukee
Table of Contents
milwaukee M18 FSAG125XB Cordless Angle Grinder
Product Information
Specifications:
- Type: Cordless Angle Grinder
- Production Code: 4832 66 01 XXXXXX MJJJJ
- Battery Voltage: 18 V
- Rated Speed: 8500 min-1
- Thread of Work Spindle: M14
- Grinding Disc Diameter (max): 125 mm
- Grinding Disc Hole Diameter: 22.2 mm
- Grinding Disc Thickness (max): 6 mm
Product Usage Instructions
- Remove the battery pack before starting any work on the machine.
- Check the power plug and power cord for any damages. Only a specialized technician should handle repairs.
- Fully press the switch to engage the grinder. The speed will adjust automatically for efficient cutting.
Safety Instructions:
- Always ensure the battery pack is removed before working on the machine to prevent accidents.
- Inspect the power cord for any damages before use to avoid electrical hazards.
Operating Instructions:
- Fully press the switch to start the grinder.
- Allow the grinder to run at reduced speeds until the blade engages with the workpiece.
- The speed will automatically increase for optimal cutting efficiency.
Care and Maintenance:
Regularly check the grinder for any signs of wear and tear, and clean it
after each use for optimal performance.
Product Storage:
Store the grinder in a dry and secure place away from children’s reach when
not in use.
FAQ (Frequently Asked Questions):
Q: How do I change the grinding disc on the angle grinder?
A: To change the grinding disc, first, make sure the grinder is
unplugged or the battery is removed. Use the provided wrench to loosen the nut
holding the disc in place, then replace the disc with a new one and tighten
the nut securely.
Original instructions
Picture section with operating description and functional description
Remove the battery pack before
starting any work on the machine.
Insulated gripping surface
TECHNICAL DATA
TECHNICAL DATA| M18 FSAG125XB| M18 FSAGV125XB|
M18 FSAGV115XPDB| M18 FSAGV125XPDB
---|---|---|---|---
Type| Cordless Angle Grinder| Cordless Angle Grinder| Cordless Angle Grinder|
Cordless Angle Grinder
Production code| 4832 66 01
XXXXXX MJJJJ
| 4832 83 01
XXXXXX MJJJJ
| 4832 75 01
XXXXXX MJJJJ
| 4832 89 01
XXXXXX MJJJJ
Battery voltage| 18 V| 18 V| 18 V| 18 V
Rated speed| 8500 min-1| 3500 – 8500 min-1| 3500 – 8500 min-1| 3500 – 8500
min-1
Thread of work spindle| M14| M14| M14| M14
D=Grinding disc diameter max.| 125 mm| 125 mm| 115 mm| 125 mm
d=Grinding disc hole diameter| 22,2 mm| 22,2 mm| 22,2 mm| 22,2 mm
| | | |
b=Grinding disc thickness max.| 6 mm| 6 mm| 6 mm| 6 mm
| | | |
| | | |
b=Cutting disc thickness max. / min.| 3 mm / 1 mm| 3 mm / 1 mm| 3 mm / 1 mm| 3
mm / 1 mm
| | | |
D=Sanding disc diameter max.| 125 mm| 125 mm| 115 mm| 125 mm
D=Wiring brush diameter max.| 75 mm| 75 mm| 75 mm| 75 mm
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah … 12,0 Ah)| 2,4 … 3,5
kg| 2,4 … 3,5 kg| 2,4 … 3,5 kg| 2,5 … 3,5 kg
- Recommended Ambient Operating Temperature -18 … +50 °C
- Recommended battery types M18B…; M18HB…
- Recommended charger M12-18…; M1418C6
Noise information: Measured values determined according to EN 60745.
- Typically, the A-weighted noise levels of the tool are:
- Sound pressure level / Uncertainty K
- 82,6 dB (A) / 3 dB (A)
- 93,6 dB (A) / 3 dB (A)
- 82,6 dB (A) / 3 dB (A)
- 93,6 dB (A) / 3 dB (A)
- Sound power level / Uncertainty K
- 82,6 dB (A) / 3 dB (A)
- 93,6 dB (A) / 3 dB (A)
- 82,6 dB (A) / 3 dB (A)
- 93,6 dB (A) / 3 dB (A)
Wear ear protectors!
-
Vibration information: Vibration total values (triaxial vector sum) determined according to EN 60745.
-
Vibration emission value ah / Uncertainty K
-
Surface grinding
- 5,01 m/s² / 1,5 m/s²
- 1,65 m/s² / 1,5 m/s²
- 5,01 m/s² / 1,5 m/s²
- 1,65 m/s² / 1,5 m/s²
-
Disc sanding
- 4,79 m/s² / 1,5 m/s²
- 1,36 m/s² / 1,5 m/s²
- 5,85 m/s² / 1,5 m/s²
- 1,81 m/s² / 1,5 m/s²
-
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING!
- The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
- The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the exposure level over the total working period.
- An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
- Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.
WARNING! Read all safety warnings and all instructions.
- Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
- Save all warnings and instructions for future reference.
ANGLE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire Brushing or Abrasive Cutting-Off Operations:
-
This power tool is intended to function as a grinder, sander, wire brush or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with
this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. -
Operations such as polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
-
Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
-
The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
-
The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>