LITEHAWK OVERDRIVE 4x4MT Twin RC Monster Truck Instruction Manual

LITEHAWK OVERDRIVE 4x4MT Twin RC Monster Truck

Product Information

• Specifications:
  • Model: LiteHawk OVERDRIVE
  • Battery: 8.4 Volt NIMH
  • Charge: USB charge
  • Charging Time: Approximately 3 hours
  • Speed: Up to 45 km/h (27.5 mph)
  • Radio Control System: 2.4 GHz
• Welcome to the world of LiteHawk!
  • The LiteHawk OVERDRIVE is a scaled-down model of a monster truck – it will race like a bullet on all kinds of terrains and amaze you with its spectacular drifts!
  • The chassis features four-wheel independent suspension and long-travel shocks that handle bumps effortlessly.
  • Step on the accelerator and race at speeds up to 45 km/h (27.5 mph)!

Product Usage Instructions

• Charging the Battery:
  • Plug in the USB cable to power – RED light indicates charging.
  • During charging, the USB light will turn to a blinking GREEN.
  • When charging is complete, the GREEN light will stay ON constantly.
  • Charging time is approximately 3 hours.
• USB Cable Protection Features:
  • If the USB short-circuits while charging, the light will be RED and BLINKING.
  • The USB cable has overvoltage protection – the Red light will be OFF if the voltage is too high.
• Radio Control System Setup:
  • Always use new AA batteries in the transmitter.
  • Ensure the transmitter is turned off.
  • Open the battery compartment using a Phillips screwdriver.
  • Insert 3 AA batteries following the indicated polarity.
  • Close the battery compartment securely.
  • Remove batteries when not using the model for an extended period.
• Battery Disposal:
  • Dispose of used batteries properly at an approved recycling centre. Don’t throw them in the trash.

FAQs

• Q: What should I do if my LiteHawk OVERDRIVE does not respond to the remote control?
  • A: Check that the batteries in the transmitter are new and inserted correctly. Also, ensure there is no interference from other electronic devices nearby.
• Q: How can I extend the battery life of my LiteHawk OVERDRIVE?
  • A: Avoid overcharging the battery and always disconnect it from the charger once fully charged. Store the vehicle and transmitter in a cool, dry place when not in use.

OVERDRIVE Precautions

LiteHawk OVERDRIVE Precautions

• The LiteHawk OVERDRIVE is not intended for children under the age of 14 unless closely supervised by an adult.
• Improper use may cause serious injury.
• Please read the NIMH Battery section before use.
• Do not run in rain, snow or if there is lightning and/or thunder.
• Do not touch ANY moving parts while the model is powered.

SAFETY PRECAUTIONS

• Keep hands, hair and loose clothing away from moving parts when the model is powered ON.
• Turn off the controller/charger and OVERDRIVE when not in use.
• Remove the battery from the controller/charger when not in use.
• Parental guidance is recommended for use.
• Keep your OVERDRIVE in your sight so that you can supervise it at all times.
• New AA alkaline batteries are recommended for use in the controller to obtain maximum performance.
• Your charger is tailor-made for the NIMH battery used in your LiteHawk OVERDRIVE. Do not use it to charge any battery other than that in the LiteHawk OVERDRIVE.

BATTERY SAFETY INFORMATION

• Requires 3 x 1.5V AA batteries (not included)
• Batteries are small objects.
• Replacement of batteries must be done by adults.
• Follow the polarity (+/-) diagram.
• Promptly remove dead batteries from the toy.
• Dispose of used batteries properly.
• Remove batteries for prolonged storage.
• DO NOT incinerate used batteries
• DO NOT dispose of batteries in a fire, as batteries may explode or leak.
• DO NOT mix old and new batteries or different types of batteries (i.e. alkaline/standard)
• Always replace the whole set of batteries at one time.
• DO NOT short-circuit the supply terminals

CARE AND MAINTENANCE

• Always remove batteries from the controller when it is not being used for a long period.
• Unplug the battery of trom toy when not in use.
• Keep the toy away from direct heat or extreme cold
• Do not expose the toy’s interior to water or moisture. This can damage the electronic assemblies.

Your LiteHawk OVERDRIVE is equipped with a NIMH battery.

• Special NIMH Battery Instructions:
  • Never charge the battery unattended.
  • Charge the battery in an isolated area. Keep away from flammable materials.
  • Do not be exposed to direct sunlight. There is a risk of the batteries exploding, overheating or igniting.
  • Do not disassemble, modify, heat or short-circuit the batteries. Do not place them in fires or leave them in hot places.
  • Only charge the batteries with the specified battery charger.
  • Only use the batteries in the device specified by LiteHawk.
  • Batteries must be recycled or disposed of properly.
  • Do not leave plugged into the model when not in use.
  • Do not charge if the battery or connector is wet.

Before charging the LiteHawk OVERDRIVE please read the following!

• DO NOT leave the battery unattended during charging.
• DO NOT leave the battery plugged into the charger any longer than 4 hours maximum. If the charging light does not turn off in this time, the charger or battery could be faulty – unplug immediately!
• DO NOT install another battery without letting the motor cool first! 5-10 minutes is sufficient.
• DO NOT recharge the battery until it is cool to the touch! 10 minutes is sufficient.
• DO NOT charge if the battery or connector is wet.
• Remove the battery from the model when charging.

Welcome to the World of LiteHawk!

• Before we get ready for your first driving adventure, let’s cover the basics together!
• OVERDRIVE is a scaled-down version of a monster truck – it will blast across all types of terrain and thrill with big slides! The chassis is designed with 4-wheel independent suspension, and long travel shocks that soak up bumps. Punch the throttle and race up to speeds of 45km/h (27.5 mph)!
• Attempting to use your LiteHawk OVERDRIVE without completely reading the manual may cause injury to yourself and people in the vicinity, as well as damage to the R/C model. Please read the Instruction Manual thoroughly before using this product.

LiteHawk R/C Car and Truck Terms 101

• Transmitter: The hand-held radio unit that sends throttle and steering inputs to your model. Also known as the radio or controller.
• Servo: A small motor unit in your model that operates the steering mechanism.
• ESC: The Electronic Speed Control provides digital proportional throttle control to the model’s motor based on your throttle input on the radio.

LiteHawk OVERDRIVE – Transmitter Set Up

• Always use fresh AA batteries in the Pistol Grip Radio Controller (Transmitter).

1. Make sure the transmitter is turned off.
2. Open the Battery Cover using a Phillips screwdriver (not included).
3. Insert 3 x AA batteries, noting the correct polarity.
4. Replace the battery door securely.

• ALWAYS REMOVE THE BATTERIES FROM THE TRANSMITTER WHEN YOU WILL NOT BE USING YOUR MODEL FOR LONG PERIODS.
• Dispose of and recycle correctly when there is no longer power in the batter-ies, they should be disposed of at an approved battery recycling centre. DO NOT THROW IN HOUSEHOLD WASTE!
• Never expose the transmitter or batteries to moisture.

LiteHawk OVERDRIVE – 2.4 Ghz

• Your LiteHawk OVERDRIVE comes with a 2.4 Ghz radio system, which allows you to play without the fear of ever losing control! Race or play with countless other drivers.
• The range of your model is approximately 150ft which, due to its small size, is more than normal vision. The farther the model goes away from you the smaller it will become and the harder it will be to determine the model’s direction.
• We suggest you stay at a distance between 20ft-50ft, this keeps your OVERDRIVE within a safe operational distance.
• Quick Tip: Always turn the transmitter on first and off last.

Controller Functions

LiteHawk OVERDRIVE – Controller Functions

• Beginner mode: To start your new journey into the exciting world of high-speed RC truck we have equipped the OVERDRIVE a selectable speed mode. The beginner setting will allow you to maintain more control to get use to your new truck. Once your are ready flip the switch and feel the full power and torque that the OVERDRIVE can offer!

LiteHawk OVERDRIVE – Battery & Charger

Your LiteHawk OVERDRIVE comes with a 8.4 Volt NIMH battery and a USB charger. Battery:
The rechargeable battery provides the power to propel your model at high speeds. You should expect 5-8 min run time. Extra batteries are available at www.litehawk.ca.

• Once the model starts to slow, drive your model to a safe place, walk over and turn it
• Never dead short an NIMH battery (never touch positive and negative together)!
• You Must FULLY charge the battery before using your new model.
• Do not leave the battery plugged into the model when it is not being used.
• Keep the battery dry at all times.

NIMH Battery and Charger Instructions:

Your New LiteHawk comes with a rechargeable NIMH battery. This battery powers the vehicle. Please read the following information before using your new LiteHawk. Always have your model turned off when not in use.

1. When plugging in the USB cable to the power, the USB cable will turn a solid RED.
2. When charging, the USB will turn to a blinking GREEN light.
3. When finish charging, the GREEN light will be ON all the time.
4. Charging time is about 3 hours.
   • The USB cable comes equipped with short-circuit protection. If the USB short-circuits while charging, the light will be RED and BLINKING.
   • The USB cable also comes equipped with overvoltage protection. When the voltage is higher than sustainable, the Red light will be OFF.

During charging:

• It is normal for the battery to get warm during the charging process. Do not charge the battery on a surface that is flammable or can be damaged by heat.
• Do not leave the battery and charger unattended while charging.
• Do not store the battery plugged into the charger

Installation of the battery into the OVERDRIVE:

• Place your OVERDRIVE on a clean flat surface. Avoid areas where small parts may be lost. The battery is housed in the battery compartment located at the top of the chassis. Press both sides of the battery cover to remove it.
• Turn the tabs, and open the battery compartment door.
• Place your fully charged battery in the battery slot. Connect the battery connector. Don’t force it, it only goes one way!
• Replace the battery cover.

How to Start!
sites carefUl DRIVE is ready to use – however, you must follow these

1. Switch ON the transmitter.
2. Plug in the battery in the OVERDRIVE.
3. Turn the OVERDRIVE power switch ON.

Battery Guidelines:

• The battery can be re-charged many times, however, over time the battery will lose its ability to take or hold a charge. At this point the battery will need to be properly recycled.
• Do not store or leave batteries in areas with extreme heat or cold. Batteries should be left and stored at room temperature.
• Always have the battery unplugged from the toy or charger when not being used.
• Do not submerge batteries underwater. Always wipe off any water with a clean towel or rag.
• It is best to store the battery out of the toy and on a non-flammable surface.

Before you drive:

• Before every use, it’s recommended to check that the steering and drivetrain are moving freely and nothing is binding.
• Next, ensure that the model and the transmitter are working correctly.
• Before you drive your model, range-test the radio system to ensure that it operates properly!
• Turn on the transmitter and then the model, and check its operating as it should.
• Walk away from the model giving steering input with the radio until you reach the maximum distance you are planning to drive your model.
• If you lose input control walk back towards the model.
• You now know the safe operating distance for your immediate environment.
• Do not attempt to operate the model if there is any problem with the radio system/external interference with your radio signal at your location.

Let’s hit the road!

• When heading out to drive your model, it’s important to always use common sense. Your new Car/Truck is fast and at top speed, you are covering over 32ft per second! For this reason, it is best to stand in the middle of the area where you want to use your car. Doing this will keep the Car/Truck closer to you and maximize the radio range. Driving in an abusive and or rough style will only result in damage, broken parts, or poor performance.
• The ESC system is not waterproof. Avoid driving through puddles, mud, or snow. If water gets into the electronics it could damage them.
• Avoid overloading your model. Never run it in areas where its movement will be restricted- ed, thick grass, weeds, mud etc. as this can over stress the motor and bind the drive- train.
• Ensure nothing prevents the smooth running of the moving parts.
• Do not run your model in confined spaces. This is an outdoor toy, do not run in your home.
• Never run your model in a public space where it might upset or endanger people or wildlife.
• Immediately discontinue the use of your vehicle and transmitter if you see lightning or hear thunder. Never use your vehicle in the rain.
• Do not dismantle or tamper with this R/C vehicle or its transmitter. The manufacturer and distributor will accept no responsibility, expressed or implied, for accidents or injuries caused as a result of disassembly, modification and/or usage against the instructions for this product.
• The transmitter’s range will vary depending on your surroundings and battery strength. Do not operate the model too far away or control could be lost (stay within 20-50 ft).
• Ensure that all batteries are correctly installed and that the NIMH battery is fully charged and in good condition.
• Do not touch ANY moving parts during operation.
• Don’t run on public roads with traffic!
• If your Car/Truck becomes stuck against something, release the throttle. Do not continue to push the throttle or run the motor. Do not try to push, pull, or tow objects of any weight as this will increase heat in the electronics and cause failures.

LiteHawk OVERDRIVE – After Use Care

1. When you have finished using your LiteHawk OVERDRIVE you should first disconnect the NIMH battery, then switch OFF the transmitter.
2. Remove the NIMH battery from the vehicle.

Care and Maintenance

• When you are finished running your model for the day, blow it off with compressed air or use a soft-bristled paint brush to dust off the vehicle.
• Always disconnect and remove the battery from the model whenever the model is stored.
• Your model is going to require maintenance to stay in tip-top running order.

Check for the following:

1. Check the wheels and steering for binding.
2. Check the tightness of the wheel nuts with the wheel wrench.
3. Look for any cracked, bent, or damaged parts
4. Check for any loose screws in the chassis structure or suspension
5. Inspect the gears for wear, and broken teeth.

LiteHawk OVERDRIVE – Storage

• Remove all batteries before storing your vehicle.
• Never store your LiteHawk OVERDRIVE near open flames, in high temperatures (including near radiators) or direct sunlight. Ideally, place the model in a warm dry location.
• Care must be taken when handling rechargeable batteries to avoid the possibility of injury and/or damage to property.

LiteHawk Parts & Tech

• There’s nothing worse than buying a new toy, having a question, or needing a replacement part, and then being left out in the cold. No worries! We pride ourselves on the very best customer service!
• We have all the parts you’ll ever need to keep your new LiteHawk in tip-top shape!
• Like we always say, “Accidents happen, even to the best of us”…. with that in mind www.litehawk.ca is available 24 hours a day, 7 days a week!
• We ship your parts Same Day! Except weekends of course – that’s when we are out playing too!

LiteHawk Guarantee

• All LiteHawk products have been tested and designed to perform as claimed out of the box. If you have an issue with a product or part of a product please contact us directly.
• We cover claims towards manufacturing defects. We know that there is nothing worse than having a question or needing a replacement part and having nowhere to go. Lite-
• Hawk is not responsible for covering the costs of replacement parts or repair on products that have been damaged due to product use.
• See all of our Litehawk products in action! Everything from videos that show LiteHawks in their natural environments – flying, sailing, power boating….to helpful In-Depth product information too! It’s all just a mouse click away!
• Get the inside scoop – by joining LiteHawk INSIDER e-bulletin!
  • Keep up to speed with our newest product releases – we have some great stuff just around the corner!
  • Ever missed a contest, simply because it happened so fast? Heck, it was over before you even got to the party! LiteHawk will never, ever share your email address – it’s private and we respect that.

www.litehawk.ca.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>