ESI GIGAPORT HD under Windows Vista/7/8.1/10 (from v3.3) Software User Guide
- June 1, 2024
- ESi
Table of Contents
ESI GIGAPORT HD under Windows Vista/7/8.1/10 (from v3.3) Software
Specifications
- Product: GIGAPORT HD
- Compatibility: Windows Vista/7/8.1/10 (from v3.3)
- Driver Version: Starting from version 3.3
- Release Date: 2015-09-16
Product Usage Instructions
Preparation
- Disconnect GIGAPORT HD from your computer if connected.
- Download and unzip the driver file you are going to install.
Installation
- Launch the setup program (an .exe file) inside the driver download by double-clicking on it.
- Follow on-screen instructions, allow any security messages, and click Next when prompted.
- Click Install when prompted and wait for files to be copied.
- Confirm additional prompts by clicking Next or Install as required.
- Once installation is complete, click Finish.
- Connect GIGAPORT HD to your computer via USB cable. Windows will automatically install the driver.
- Restart your computer manually after driver installation is complete.
Uninstallation
In case you need to uninstall the driver:
– For Windows 10: Navigate to Settings > System > Apps & features.
– For previous Windows versions: Locate it in the list of installed Programs in Windows Control Panel and remove it there.
FAQ
Q: How do I uninstall the GIGAPORT HD driver?
A: You can uninstall the driver by navigating to Settings > System > Apps & features (Windows 10) or through the list of installed Programs in Windows Control Panel for earlier Windows versions.
Knowledge Base
Installation of GIGAPORT HD under Windows Vista/7/8.1/10 (from v3.3)
original release: 2015-09-16 | ID: KB00239EN
Introduction
This text describes how to install the GIGAPORT HD driver under Windows 10 (32- or 64-bit) with driver versions starting from version 3.3. The process is virtually the same for Windows Vista, Windows 7, Windows 8 and Windows 8.1. A description of the installation with earlier drivers (up to version 3.0) can be found here.
Preparation
If GIGAPORT HD is connected to your computer with the USB cable, disconnect it
now. You will need to connect it again later during the installation.
Make sure that you have downloaded and unzipped the driver file with the
driver you are about to install.
Installation
To start the installation, launch the setup program, which is an .exe file that is inside the driver download, by double clicking on it. Typically the filename is something like GIGAPORT_HD_vX.YY_setup.exe where X.YY is the version number of the driver. When launching the installer, Windows might display a security message. Make sure to allow the installation. After that, the following dialog will appear:
Click Next and then the following dialog will appear:
Now click Install. Files are now being copied. After some time an additional dialog will appear:
Confirm this by clicking Next. Again some files are being copied and typically you will be prompted with a Windows Security message like this:
Confirm it by clicking Install. After a while the installation then will be completed and the following dialog will appear:
Once you see this, click Finish.
Now you need to connect GIGAPORT HD to your computer with the USB cable.
Windows will automatically install the driver for it, which is a process that
runs in the background and normally takes a few seconds (up to a couple of
minutes). Once this process is finished, please restart your computer
manually. Once the system starts again and you are logged in, you will see
that the GIGAPORT HD control panel is now automatically being loaded and
displayed – the installation is finished.
Uninstallation
In case you need to uninstall the driver at a later time, you will find it under Settings > System > Apps & features (under Windows 10) or in the list of installed Programs in Windows Control Panel (with previous Windows versions). You can simply remove it there.
Copyright © 1998-2024 ESI Audiotechnik GmbH – All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>