TELECO MIO Series 2 Channel Transmitter Instruction Manual
- June 1, 2024
- TELECO
Table of Contents
TELECO MIO Series 2 Channel Transmitter
This document is the property of Teleco Automation Srl, which reserves all reproduction and copyrights.
PRODUCT DESCRIPTION
UHF band transmitter with PPL controlled carrier frequency. This type of transmitter is used for controlling devices for domestic use, automatic openings, ON-OFF light control, dimming, etc. This appliance transmits a rolling code type signal to guarantee maximum secrecy. The transmitter code can be stored in the receiver directly via the latter or via radio from the transmitter. With the second possibility you can add new transmitters to an existing system without having to touch the receiver. This can be done directly by the end user (the installer’s help is not required). The code is stored in the receiver’s EEPROM memory that retains it even if power is cut temporarily.
USE INFORMATIONS
The trasmitter is in no way protected against interference from other telecommunication equipment or systems (e.g. authorised radio systems working on the same frequency range). If you are having problems with its range of action, fix the transmitter up high. Change the battery if necessary.
GENERAL SAFETY RULES
- Keep the transmitter out of the reach of children or animals.
- Do not use the manual transmitter in places or where systems are sensitive to radio emissions (e.g. airports, hospitals).
- Do not keep or use the manual transmitter in places that are damp, where there is steam, high air humidity, dust or where it is exposed to the direct rays of the sun or similar environmental conditions.
- Store the transmitter in stable conditions; the fall can cause damage or a reduction in the range of action.
WARNINGS
KEEP
OUT OF REACH OF
CHILDREN.
DO NOT INGEST THE BATTERY, DANGER OF CHEMICAL BURNS.
- This product contains a coin/button cell battery. If the coin/button battery is swallowed, it can cause severe internal burns in as little as 2 hours and lead to death.
- Keep new and used batteries out of the reach of children.
- If the battery compartment does not close securely, stop using the product and keep it out of the reach of children.
- If you suspect that batteries have been swallowed or inserted into other body orifices, seek immediate medical attention.
WARNINGS
EXPLOSION HAZARD IF THE BATTERY IS SUBSTITUTED INCORRECTLY.
- Replace the battery with a CR2032 type battery only.
- Always wrap the battery up, both when it is being stored and when it is being disposed of. The battery should not come into contact with other metal objects as it could cause the battery to run down, catch fire or be damaged.
- Dispose of damaged or finished batteries immediately in compliance with the law. To this end, contact the authorities for safeguarding the environment or the centre for disposing of waste materials in your area. Do not throw the battery away with household rubbish.
TRANSMITTER KEYS
The transmitter is equipped with two or four keys depending on the model from
CH1 to CH4.
On the back there is also a hidden key P3 ( see figure 1 ) used for
programming the receiver.
CHANGING THE BATTERY
see figure 2
Figure 2
GUARANTEE
The guarantee complies with the law. If the guarantee has to be used please refer to the specialized retailer. The right to the guarantee is applicable only for the country in which the manual transmitter was purchased. The batteries are not covered by the guarantee.
MEMORIZE,DELETE,COPY A TRANSMITTER
Follow the receiver’s instructions.
UE CONFORMITY DECLARATION (TVMIO868)
The manufacturer, Teleco Automation s.r.l, declares that the type of radio
equipment is compliant with Directive 2014/53 / EU.
The full text of the EU compliance declaration is available at the following
Internet address:
www.telecoautomation.com/ce
USA & CANADA CONFORMITY DECLARATION (TVMIO916)
According to FCC regulations, the device is designed as a mobile station.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
“During its normal function, keep a distance of at least 5 mm from the radiant element.”
Any changes or modifications not expressly approved by the party responsible for compliance could void the User’s authority to operate the equipment”
According to ISED regulations, the device is designed as a mobile station.
“This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.”
“During its normal function, keep a distance of at least 5mm from the radiant element.”
TECHNICAL SPECIFICATIONS
Carrier frequency| TVMIO868xxxx
TVMIO916xxxx| 868.3 MHz
---|---|---
ERP| 0 dBm| 916 MHz
Power supply| 3V±10% (lithium battery CR2032)
Consumption when transmitting| 12 mA
Working temperature| -10° +55°C
The transmitters are coded directly by the manufacturer with a different code
for each transmitter.
After pressing one of the buttons for more than 30 seconds, the transmission
will be automatically interrupted.
****: Refer to the text in the instructions
Customer Support
TELECO AUTOMATION SRL
Via dell’ Artigianato, 16 – 31014 Colle Umberto (TV) ITALY
TELEPHONE: +39.0438.388511 –
www.telecoautomation.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>