TELECO TVMIO868 Remote Control Roller Doors User Guide
- June 1, 2024
- TELECO
Table of Contents
TELECO TVMIO868 Remote Control Roller Doors
Product Information
Specifications
-
Product Name: Teleco Simple Easy Setup for GDO Roll 77 Electric
Remote Control Roller Doors -
Manufacturer: Samson Doors
-
Contact: Tel: 01933 448 850, Website: www.samsondoors.co.uk
Product Usage Instructions
What’s in the Box?
The box includes:
- Installer’s instruction manual
- Drill hole mounting template
- Teleco simple panel (with power supply)
- Teleco hand transmitter (TVMIO868) x2
- 5A fuse spare (T5AL250V)
- Control panel plastic glands x2
- Control panel case screws (3.5mm x 31mm Pozi self-tapping screw) x4
Mounting the Control
To mount the control:
- Use the drill hole mounting template to mark hole positions.
- Be cautious to avoid wall damage and use appropriate fixings.
- Mount the panel to the structure in the highlighted locations.
Know Your Way Around
The control features include:
- Motor & power supply terminal block
- Accessories terminal block
- Up & down buttons
- Dipswitches
- Arial
- Fuse
Frequently Asked Questions
- Q: How do I troubleshoot issues with the control unit?
- A: Refer to the installer instruction manual supplied with the control unit for troubleshooting guidance.
What’s in the box
- X1 Installer’s instruction manual
- X1 Drill hole mounting template
- X1 Teleco simple panel (with power supply)
- X2 Teleco hand transmitter (TVMIO868)
- X1 5A fuse spare (T5AL250V)
- X2 Control panel plastic glands
- X4 Control panel case screws (3.5mm x 31mm pozi self tapping screw)
Mounting the control
Using “drill hole mounting template”, mark hole positions desired. WARNING:
Sticking to the wall could cause damage. Be mindful when doing so. Use
appropriate fixings to mount the panel to the structure in the highlighted
locations.
Know your way around
- Motor & power supply terminal block
- Accessories terminal block
- Up & down buttons
- Dipswitches
- Arial
- Fuse
Initial power up
Control board will be in the default start up which restricts you from adding
features to the board. This is identified by L1 & L2 light blinking slow. Exit
this mode by pressing the P1 & P2 buttons (together) 3 times, holding both
buttons down on the 3rd press for 5 seconds.
Wiring
Wiring the motor
Motor wires to fit into terminals 1, 5, 6, 7:
- 1 – Green/Yellow wire
- 5 – Black wire
- 6 – Blue wire
- 7 – Brown wire
Wires are to be fed up through the bottom of the control board & secure using a panel plastic gland supplied with the control box.
NOTE:If motor direction is not correct, swap the black and brown wires.
Wiring the safety edge
Safety edge wires to be fitted into terminals 16, 17 & 18:
- 16 –Brown wire
- 17 –Green wire
- 18 –White wire
Programming
Adding transmitters
- Enter programming mode Press & hold P1 & P2 for 5 seconds (L1 &L2 will begin flashing and board will bleep)
- Select control setting & pairtransmitter Press & hold P2 Whilst holding P2 press a button on the transmitter Pairing is complete once the board bleeps 11 times.
- Exit programming mode by leaving thecontrol board alone for 10 seconds,both L1 & L2 will stop flashing.
NOTE:More transmitter options can be found in the “installers instruction
manual” supplied with the control panel
Removing transmitters
- Enter programming mode Press & hold P1 & P2 for 5 seconds (L1 &L2 will begin flashing and board will bleep)
- Select control setting & unpair transmitter Press P1 4 times, on the 4thpress, hold P1 down. Whilst holding the P1 button, press the button of the transmitter you would like to unpair. Unpairing is complete once the board bleeps 1 long tone.
- Exit programming mode by leaving the control board alone for 10 seconds,both L1 & L2 will stop flashing.
Troubleshooting
Image to the right was abstracted from “Installer instruction manual” supplied
with the control unit.
References
- Security Shutters & Security Grilles | Industrial Sectional Roller Doors | Commercial, Timber Doors,
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>