LEGEND 0414-0753 AXEO Front Suspension Instruction Manual

LEGEND 0414-0753 AXEO Front Suspension

INSTALL INSTRUCTIONS

1. STEP ONE: FORK REMOVAL
   A. Remove the forks from the trike, consult with an experienced technician before removal if needed.
   

2. STEP TWO: DISASSEMBLY
   WARNING: Be extremely careful when removing the top cap, it is under high spring pressure and may cause injury.
   A. Secure the stanchion (upper fork tube) in a fork vise or soft clamp to avoid scratching it.
   B. Use an impact wrench to remove the lower Allen bolt to drain the fork oil. FIGURE A
   
   C. Pump the slider (lower fork tube) and stanchion several times to purge as much of the original oil as possible.
   D. With the fork still secured in the vise, use an impact wrench to remove the top cap. FIGURE B
   
   E. Dump out all of the stock components from the top of the stanchion. FIGURE C
   
   NOTE: Disassembling the slider and stanchion is unnecessary unless:
   ◦ You are replacing your fork seals and bushings.
   
   0414-0753: Customer re-uses OEM oil lock pieces
   0414-0755: Customer re-uses OEM oil lock pieces

3. STEP THREE: CLEAN FORKS
   A. Clean the remaining oil and contaminants from the inside of the fork tubes using a non-corrosive and non-abrasive parts cleaning solvent and a long brush.
   B. Rinse thoroughly to remove any residue.
   C. Dry parts with compressed air.

4. STEP FOUR: SET PRELOAD ON LEGEND CARTRIDGES
   A. Refer to the preload setting chart on the back cover of this install guide (preload measurement is based on rider weight only).
   B. Use an Allen wrench to loosen the set screw on the preload adjuster. FIGURE D
   
   C. Thread the preload adjuster up or down the shaft to achieve the recom- mended inside measurement between the rebound spring perch and the preload adjuster.
   IMPORTANT: Once the proper preload measurement is achieved, index preload adjuster so the set screw lines up with the machined flat on the shaft. Apply blue threadlocker to the set screw threads and tighten.

5. STEP FIVE: INSTALL LEGEND CARTRIDGES
   A. Make sure the oil lock piece aligns with the stanchion (use a flashlight to ensure you can see all the way through the fork to the lower bolt hole).
   IMPORTANT: Verify that the stock rebound springs are removed.
   B. Install the provided rebound springs into the top of each stanchion. FIGURE E
   
   C. With the slider and stanchion fully compressed, install the cartridge, making sure it is seated in the oil lock piece.
   D. Clean and inspect the copper sealing washer and the threads of the lower Allen bolt that were removed in Step 2. Make sure there are no blemishes that would prevent the washer from sealing.
   E. Install the lower Allen bolt and the copper sealing washer.
   F. Hold the cartridge and tighten the lower Allen bolt to 30 ft. lbs.

6. STEP SIX: ADDING OIL AND BLEEDING
   IMPORTANT: The type and amount of oil added ensures that the hydraulic bump stop functions properly.
   A. Refer to the oil volume chart on the back cover of this install guide for the type and amount of oil to add per fork.
   B. Pour oil in the top of the stanchion, you will need to slowly pump the stanchion and slider a few times while doing this to distribute the oil. FIGURE F
   
   C. Once the recommended amount of oil has been installed, slowly pump the stanchion and the slider up and down 10 to 12 times to bleed the air from the oil. FIGURE G
   
   D. After bleeding the air from the oil, slide the stanchion up and thread it onto the fork cap.
   E. Tighten the fork cap to 25 ft. lbs.

7. STEP SEVEN: INSTALL FORKS
   A. Once the forks are re-assembled, install them onto the trike. Follow the manufacturers’ torque specs for safety

PARTS INCLUDED

• (2) – AXEO Cartridges
• (2) – Rebound Springs

PRELOAD SETTING CHART

PRELOAD MEASUREMENT

19-24 TRIKE 49MM
UP TO180 LBS| 1/4”| 1/4”
180-240 LBS
FACTORY SETTING| 3/8”| 3/8”
240-300 LBS| 1/2”| 1/2”
300+ LBS| 5/8”| 5/8”

PRELOAD MEASUREMENT

TAKEN BET WEEN REBOUND SPRING PERCH AND PRELOAD ADJUSTER-AS SHOWN BELOW

OIL VOLUME CHART

AXEO PART| TUBE SIZE| FITMENT| FORK TUBE LENGTH| OUNCES OF OIL PER LEG
---|---|---|---|---
0414-0753| 49 mm| 2014-2018| STD| 13 oz
0414-0755| 49 mm| 2019-2024| STD| 13 oz

NOTE: LEGEND SUSPENSIONS RECOMMENDS THE USE OF THE FOLLOWING FORK OILS: SCREAMIN’ EAGLE HEAVY, MAXIMA 20W V-TWIN, OR AN EQUIVALENT 20W FORK OIL

Please visit www.legendsuspensions.com for the translated version of this install guide in the following languages: French, German, Italian, and Spanish. Please choose your preferred language at the top of the page and then choose the product you purchased. The install guides are located on the bottom of the product page under Product Downloads.

FITMENT:
0414-0753
2014-2018 HARLEY-DAVIDSON TRIKE MODELS (49 MM)

0414-0755
2019-2024 HARLEY-DAVIDSON
TRIKE MODELS (49 MM)

NOTE: LEGEND SUSPENSIONS RECOMMENDS THE USE OF THE FOLLOWING FORK OILS: SCREAMIN’ EAGLE HEAVY, MAXIMA 20W V-TWIN, OR AN EQUIVALENT 20W FORK OIL

CUSTOMERS SUPPORT

Please scan the QR code to access product install guides and warranty in your selected language.

For more information visit www.legendsuspensions.com

WWW.LEGENDSUSPENSIONS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>