Shenzhen Clot Robotics ME1252C001F7 Spray Robot User Manual
- June 3, 2024
- Shenzhen Clot Robotics
Table of Contents
Specification of Spray Robot
Product Overview
The spray robot performs smart sterilization of spaces with the combined use of SLAM and traditional sterilization technologies. Using ultrasonic atomization technology, it atomizes disinfectant into micro-sized particles, which disperse in air in the form of aerosol and kill pathogenic microorganisms, thus achieving the purpose of sterilization. The robot can work and get charged automatically. It can also upload information on its running status, operating status and task implementation in real time. Users can locally or remotely assign sterilization tasks so that the robot will fulfill the sterilization tasks actively, efficiently and accurately. The spray sterilization robot, which is widely applied in hospitals, schools, hotels, office buildings, factories and supermarkets, effectively improves sterilization efficiency and guarantees public health security in places where it is used.
Product Appearance
Product Parameters
Basic parameters| Overall dimension| 500mm×500mm×1182mm (excluding spray
cylinder)
---|---|---
500mm×500mm×1430mm (including spray cylinder)
Package dimension| 620mmx620mmx1500mm
Net weight| 59.5kg
Gross weight| 71.5kg
Operating system| Android 7.1
Touch screen| 10.1-inch; resolution: 1280×800
CPU| RK3288
RAM| 2GB
ROM| 8GB
Network| 4G/WIFI
Battery capacity| 24V, 20Ah
Working hours| 4h
Charging time| 4.5h
Standby time| 13h
Speaker| 2
Noise| ≤50dB (work normally in case of no broadcast)
Environment
| Operating environment| Temperature: 5℃~45℃; humidity: 5%～85%
Storage environment| Temperature: -10℃~60℃ (without liquid residue in chamber
and pipe); humidity: 5%～85%
Chassis parameters| Mapped area| ≤10000m²
Applicable area| ≤1000m² (calculated based on 4m floor height)
Movement speed| 0~0.8m/s (user-defined)
Width of driving passage| ≥800mm
Sensor| Single-line laser, RGBD TOF camera (optional), ultra- sonic wave,
6-axis gyroscope
Width of surmountable trench| ≤40mm
Climbability| ≤5°
Height of surmountable obstacle| ≤10mm
Minimum turning radius| 0
Maximum rotational speed| 60°/s
Positioning accuracy| ±5cm
| Wheels| 2 differential wheels + 4 mecanum wheels + 1 auxil- iary directional
wheel
---|---|---
Parameters of charging piles| Charging mode| Automatic recharging by contact
Input| AC110-240V
Output| 29.4V, 7A
Sterilization parameters| Sterilization method| Ultrasonic atomization
Atomization parameters| Atomizer specification| 4-head
Atomization efficiency| 1.5h/L
Size of atomized particles| <10um
Disinfectant| Sodium hypochlorite solution (concentration≤200ppm)
Tank volume| 10L
Product Functions
Sterilization| Sterilization method| Using ultrasonic atomization technology,
the robot atomizes disinfectant into micro-sized particles, which disperse in
air in the form of aerosol and kill pathogen- ic microorganisms, thus
achieving the purpose of sterilization
---|---|---
Automatic charging| Automatic recharge for low battery| When its electric
quantity is below the preset value, the robot will return to the charging pile
for charging
Return to a charging pile at free time| The robot will automatically return to
the charging pile for charging at the end of a task or at free time
Operation| User-defined task| The robot can define path, time and location for a
sterilization task by software
Navigation and obstacle avoidance| Fully automatic navigation| The robot can
navigate according to location, time, path and automatically planned route for
a task
Automatic obstacle avoidance| In executing a task, the robot can automatically
move across obstacles it senses
FCC compliance statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important: Changes or modifications to this product not authorized by
Shenzhen ClOT Robotics Co., Ltd could void the electromagnetic compatibility
(EMC) and wireless compliance and negate your authority to operate the
product.
This product has demonstrated EMC compliance under conditions that included
the use of compliant peripheral devices and shielded cables between system
components. It is important that you use compliant peripheral devices and
shielded cables between system components to reduce the possibility of causing
interference to radios, televisions, and other electronic devices.
RF Exposure Statement:
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body.
Use only the supplied antenna.
FCC ID: 2A5WH-ME1252C001F7