LUMI Legend FS29-46F-03 Easel Studio TV Floor Stand with Soundbar Instruction Manual

LUMI Legend FS29-46F-03 Easel Studio TV Floor Stand with Soundbar

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor tor assistance.
CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. Use the mounting
• Screws provided and Do NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

IMPORTANT: Ensure that you have received all arts accordion to the comment  component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase tor a replacement.

MAINTENANGE: Check that the product is secure and safe to use at regular intervals (at least every three months).

SOUNDBAR
INSTRUCTION MANUAL

• Operating temperature:-10″C-40″C
  

IR Remote Control

Short Press

• ON/OFF
• Mute/Unmute
• Volume +
• Prev
• Play/Pause
• Next
• Volume- AUX Input
• HDMI Input
• Bluetooth Input
• OPT Input
• USB Input

Long press

• Volume+ Volume+

Note: AUX and USB Inputs have priority when switching sources Use the remote control or control panel to switch between other sources.

CONTROL PAMNEL

1. Power / Mode
   • Long press for ON/OFF
   • Short press to change Source modes
2. Previous/ Volume Down
   • Short press for Previous Song (Bluetooth or USB Only)
   • Long press to decrease volume (one degree with each light flash)
3. Next/Volume Up
   • Short press for Next Song (Bluetooth or USB Only)
   • Long press to increase volume (one degree with each light flash)
4. Play/ Pause
   • Press once to Play or Pause the music(Bluetooth or USB Only)
   • In other source modes press once to Mute/ Unmute audio
5. Status Indicator Panel Light
   Flashing Blue: Waiting to Pair Bluetooth
   Solid Blue: Bluetooth Mode Connected Solid Green: AUX Input
   Solid Yellow: USB Input Solid Red: OPT Input
   Solid Purple: HDMI Input
   Flashing   Red: Reset required

BACK PANEL

SETTING UP SOURCE INPUTS

1. Bluetooth Input
   • Press the “*” button on the Remote Control or press and hold the Power Button on the control panel until the panel is flashing blue.
   • Set your phone (or other device) to Bluetooth discoverable mode and search for Soundbar in the device list. Select the Soundbar to connect.
   • The control panel will turn solid blue when Bluetooth is connected to your device.
   • If unsuccessful, repeat the steps above.
   • Select music to play.
2. HDMI Input
   • Ensure the TV/ HDMI source has an Audio Return Channel (ARC).
   • Insert the HDMI into the Soundbar’s HDMI port using HDMI Cable rated 1,4 or higher.
   • Press the “HDMI” on the Remote Control or touch the power
   • Switch on the control panel several times until the panel light turns solid Purple.
   • Consult your TV’s Owners Manual if the HDMI ARC is not detected automatically by the Soundbar. Select your music. TV or other content to play.
3. Optical (To slink) input
   • Connect the TV or other device to the Soundbar using optical/To slink cable.
   • Press the “OPT” button on the Remote Control or touch the power switch on the control panel several times until the panel light turns solid Red.
4. AUX Input
   • Connect your TV or other device to the Soundbar using a 3.5mm Stereo cable by plugging the cable into the AUX input found on the Soundbar,
   • The music source will automatically switch to AUX mode and the control panel light will flash Green.
   • Use the Remote Control or touch the power switch on the control panel several times to switch to other modes. When in the AUX mode the control panel light will turn solid Green.
5. USB Input
   • Insert a USB thumb drive into the USB port of the Soundbar music content will play automatically. Music files should be located in the main directory of the thumb drive.
   • Use the Remote Control or touch the power switch on the control panel several times to switch to other modes When in the USB mode the control panel light will turn solid Yellow,

Note: USB port is not output port but to signal transmission.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not Occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oft and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Safety Disclaimer
This product includes a Safety Wire Kit that must be used in conjunction with the product and will prevent the product from falling or tipping over. Please follow the enclosed Safety Disclaimer information to properly install these safety accessories. In no event shall the Seller be liable for any direct, indirect, punitive, incidental, special consequential damages, to property or life, whatsoever arising out of or connected with the use or misuse of this product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>