AMERICAN LEGEND AL4100F 9 Inch Electronic Arcade Speedball Instruction Manual

AL4100F 9-Inch Electronic Arcade Speedball
Instruction Manual

We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. However, if you have any problems with your new product,
DO NOT RETURN IT TO THE STORE, please contact us toll-free @: 1-888-996-2729
FAX: 1-866-873-3531
gameroom@escaladesports.com

Mailing Address: (Correspondence Only)
Escalade Sports
PO Box 889
Evansville, Indiana 47706-0889
Physical Location:
Escalade Sports
817 Maxwell Ave.
Evansville, Indiana 47711
Please visit our Web site at: www.escaladesports.com
Please have your model number when inquiring about parts.
When contacting Escalade Sports please provide your model number, date code (if applicable), and part number if requesting a replacement part. These numbers are located on the product, packaging, and this owner’s manual.
Your Model Number ____ AL4100
Date Code ___ 2 – AL4100- – HL
Purchase Date ____
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT! READ EACH STEP IN THIS MANUAL BEFORE YOU BEGIN THE ASSEMBLY.
IMPORTANT!
THE DRAWINGS IN THIS MANUAL MAY BE EXAGGERATED OR MODI TO SHOW DETAILS.
TWO ADULTS ARE REQUIRED TO ASSEMBLE
THIS 9′ ARCADE SPEEDBALL
Featuring Electronic Scoring and LED Lighting
Tools Required:
Allen Wrench (Included)
Furniture Polish and Soft Cotton Cloth
Assembly Note: During assembly, the correct orientation of all parts is critical for correct assembly. Please study all diagrams closely.
An electric screwdriver is helpful in assembly. However, please set it at low torque and use extreme caution with an electric screwdriver because you could overtighten the hardware and strip the screws.

Assembly Tips

Make sure you understand the following tips before you begin to assemble your game table.

1. Start all bolts by hand before tightening.
2. Some drawings or images in this manual may not look exactly like your product. Please read and understand the text before starting each assembly step.

ATTENTION:
READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO CAPABLE ADULTS ARE REQUIRED TO ASSEMBLE THIS GAME TABLE.
CAUTION
DO NOT STAND OR SIT ON THIS PRODUCT AND OR PLAYFIELD.
CAUTION:
To play this game and achieve a high skill level requires a soft and gentle toss of the Ball . Over tossing or overthrowing the ball could result in serious damage to the product.
Please play safe.

HARDWARE IDENTIFIER

(To Scale)

(Not to Scale)

ACCESSORIES IDENTIFIER (Not to Scale)

PARTS REQUIRED

• 1pc – P13 Left Side Apron
• 1pc – P14 Right Side Apron
• 1pc – P15 Left Top Rail with Control Switch
• 1pc – P16 Right Top Rail
• 40pcs – H3 Phillips Roundhead Screw
• 10pcs – P23 Metal Connection Plate

STEP 1
Attach the P14 Right Side Apron onto the P16 Right Top Rail using the P23 Metal Connection Plates and the pilot holes on the P14/P16, using the H3 Phillips Round Head Screws as shown in DETAIL A.
Attach the P13 Left Side Apron onto the P15 Left Top Rail using the P23 Metal Connection Plates and the pilot holes on P13/P15, using the H3 Phillips Round Head Screws as shown in DETAIL B.
Tighten, but DO NOT strip out H3 screws.
NOTE: This assembly must be made on a flat, smooth, non-abrasive surface.

PARTS REQUIRED

• 1pc – P19 Playfield with End Ramp
• 10pcs – H2 Phillips Round Head Screw

STEP 2
Attach the P19 Playfield onto the STEP 1 Assemblies using the pilot holes and the H2 Philips Round Screws as shown in FIGURE 2.
Tighten, but DO NOT strip out H2 screws. Assembly Note:
During assembly, the correct orientation of all parts is critical for correct assembly. Please study all diagrams closely.
Place all 10 pcs of H2 Screws into pilot holes by hand as that will correctly orientate the playfield with each side apron assembly.
PARTS REQUIRED

• 1pc – P1 End Apron
• 1pc – P2 Left Front Leg
• 1pc – P3 Right Front Leg
• 1pc – P17 Left Leg
• 1pc – P18 Right Leg
• 4pcs – H2 Phillips Round Head Screw
• 20pcs – H3 Phillips Round Head Screw
• 6pcs – P23 Metal Connection Plate

STEP 3
Attach the P3 Right Front Leg onto the P18 Right Leg using the P23 Metal Connection Plates, the pilot holes, and the H3 Phillips Round Head Screws as shown in DETAIL C.
Attach the P2 Left Front Leg onto the P17 Left Leg using the P23 Metal Connection Plates, the pilot holes, and the H3 Phillips Round Head Screws as shown in DETAIL D.
Attach the DETAIL C / D Assemblies onto the P1 End Apron using the pilot holes and the H2 Phillips Round Head Screws as shown in FIGURE 3.
Tighten, but DO NOT strip out H2, and H3 screws.

PARTS REQUIRED
1pc – P33 Plastic Connector (Playfield to Front Leg)
STEP 4
Connect the STEP 3 Front Leg Assembly onto the Playfield Assembly using the P33 Plastic Connector as shown in FIGURE 4. PARTS REQUIRED

• 4pcs – H1 Phillips Round Head Screw
• 4pcs – H3 Phillips Round Head Screw

STEP 5
Attach the STEP 3 Front Leg onto the STEP 2 Assembly using the pilot holes and H1 Phillips Round Screws, and H3 Phillips Round Screws as shown in FIGURE 5.
Tighten, but DO NOT strip out H1, and H3 screws. PARTS REQUIRED

• 2pcs – P24 Middle Support Board
• 1pc – P25 End Support Board
• 6pcs – P30 Black Plastic “L” Bracket
• 12pcs – H7 Phillips Round Head Screw

STEP 6
Attach the P30 Plastic “L” Brackets onto the P24 / P25 Support Boards using the pilot holes and the H7 Phillips Round Screws as shown in FIGURE 6.
Tighten, but DO NOT strip out H7 screws. PARTS REQUIRED
12pcs – H3 Phillips Round Head Screw
STEP 7
Attach the P24 / P25 Support Board Assemblies onto the Side Aprons using the pilot holes and the H3 Phillips Round Screws as shown in FIGURE 7.
Tighten, but DO NOT strip out H3 screws.
Assembly Note: During assembly, the correct orientation of all parts is critical for correct assembly. Please study all diagrams closely. PARTS REQUIRED

• 2pcs – P21 Connecting Board
• 6pcs – H4 Allen Head Bolt
• 6pcs – H5 Flat Washer
• 6pcs – H6 Lock Washer

STEP 8
Attach the P21 Connecting Boards onto the inside of the Side Aprons using the H4 Allen Head Bolts, H5 Flat Washers, H6 Lock Washers as shown in DETAIL H.
Tighten H4 bolts using T1 Allen Wrench— DO NOT overtighten.

PARTS REQUIRED

• 1pc – P20 Wooden Support Brace
• 1pc – P26 Plastic Ball Return
• 2pcs – H3 Phillips Round Head Screw

STEP 9
Attach the P20 Wooden Support Brace onto the P26 Plastic Ball Return using the H3 Philips Round Screws as shown in FIGURE 9.
Tighten, but DO NOT strip out H3 screws.
Assembly Note: During assembly, the correct orientation of all parts is critical for correct assembly. Please study all diagrams closely.

PARTS REQUIRED
2pcs – H2 Phillips Round Head Screw
STEP 10
Install and attach the P26 Plastic Ball Return onto the P24/25 Support Boards using the H2 Philips Round Screws as shown in DETAIL I.
Tighten, but DO NOT strip out H2 screws. PARTS REQUIRED

• 1pc – P22 Goal Box Bottom Board
• 4pcs – H2 Phillips Round Head Screw

NOTE: NEED 2 ADULTS FOR ASSEMBLY
STEP 11
Attach the P22 Goal Box Bottom Board onto the P25 End Support Board using the H2 Philips Round Screws as shown in DETAIL J.
Tighten, but DO NOT strip out H2 screws. PARTS REQUIRED

• 1pc – P7 Right Back Leg
• 1pc – P8 Left Back Leg
• 1pc – P28 Back Board – D
• 4pcs – H2 Phillips Round Head Screw

NOTE: NEED 2 ADULTS FOR ASSEMBLY
STEP 12
Attach the P28 Lower Front Cabinet Board onto the P7 / P8 Back Legs using the pilot holes and the H2 Phillips Round Screws as shown in FIGURE 12.
Tighten, but DO NOT strip out H2 screws. PARTS REQUIRED

• 6pcs – H4 Allen Head Bolt
• 6pcs – H5 Flat Washer
• 6pcs – H6 Lock Washer

NOTE: NEED 2 ADULTS FOR ASSEMBLY
STEP 13
Attach the STEP 12 Assembly onto the STEP 11 Assembly using the H4 Allen Head Bolts, H5 Flat Washers, and H6 Lock Washers as shown in FIGURE 13.
Tighten all H4 Bolts using the T1 Allen Wrench— DO NOT overtigten. NOTE: If H4 Bolts are difficult to start, see STEP 8, loosen those H4 Bolts, move the P21 slightly, start the bolts and tighten all bolts.
PARTS REQUIRED

• 1pc – P4 Ball Stop Bottom Board
• 4pcs – H1 Phillips Round Head Screw

STEP 14
Attach the P4 Ball Stop Bottom Board onto the P7 / P8 Back Legs using pilot holes and the H1 Phillips Round Screws as shown in FIGURE 14.
Tighten, but DO NOT strip out H1 screws. PARTS REQUIRED

• 2pcs – H2 Phillips Round Head Screw
• 1pc – P5 Target Board with Scoring Sensors

NOTE: Need a second adult to hold the P7+P8 inward to prevent gaps between P7, P8, and P5.
STEP 15
Attach the P5 Target Board onto the P7 / P8 Back Legs using the pilot holes and the H2 Phillips Round Screws as shown in FIGURE 15.
Tighten, but DO NOT strip out H2 screws. PARTS REQUIRED

• 1pc – P10 Top Cabinet Panel for Scorer
• 1pc – P29 Electronic Scorer
• 2pcs – H1 Phillips Round Head Screw

STEP 16
Place the wires of the P29 Electronic Scorer through the hole in the P10 Top Cabinet Panel.
Attach the P29 Electronic Scorer onto the P10 Top Cabinet Panel using pilot holes and the H1 Phillips Round Screws as shown in FIGURE 16.
Tighten, but DO NOT strip out H1 screws.
Connect Male to female plugs as shown in DETAIL M. NOTE: Connectors must be turned correctly in order for them to properly connect.
PARTS REQUIRED

• 1pc – P9 Backboard with Graphic
• 4pcs – H1 Phillips Round Head Screw
• 4pcs – H4 Allen Head Bolt
• 4pcs – H5 Flat Washer
• 4pcs – H6 Lock Washer

STEP 17
Place the P9 Backboard with Graphic onto the P7 / P8 Back Legs as shown in FIGURE 17-1.
Attach the STEP 16 Assembly onto the P7 / P8 Back Legs using the H4 Allen Head Bolts, H5 Flat Washers, and H6 Lock Washers as shown in FIGURE 17-2.
Tighten the H4 Bolts using the T1 Allen Wrench— DO NOT overtigten.
Attach the P9 Backboard with Graphic onto the P7 / P8 Back Legs using the pilot holes and the H1 Phillips Round Screws as shown in FIGURE 17-3.
Tighten, but DO NOT strip out H1 screws.

PARTS REQUIRED

• 6pcs – H3 Phillips Round Head Screw
• 1pc – P27 Clear Plexiglass

STEP 18
Install the P27 Clear Plexiglass onto the P7 / P8 Back Legs and attach onto the P10 Top Cabinet Panel using pilot holes and the H3 Phillips Round Screws as shown in FIGURE 18.
Tighten, but DO NOT overtighten H3 Screws as this could crack the plexiglass.
NOTE:
The groove for the top of the P27 plexiglass is on the lower front side of the P10 top cabinet panel. If the plexiglass will not easily slip into this groove, it will be necessary to loosen the 4 pcs H4 bolts that hold the P10 top cabinet panel and carefully tap or push it forward thus moving the groove forward just enough to allow the P27 plexiglass to slip into the groove.

NOTE:
Carefully remove the protective covering from the plexiglass before installation, and avoid fingerprints on the plexiglass by wearing cotton gloves.
Using the pointed end of a knife or awl, very carefully “prick” the protective coating on the plexiglass. Pinch the raised area and remove the protective covering.

PARTS REQUIRED

• 4pcs – H1 Phillips Round Head Screw
• 1pc – P12 Lower Back Cabinet Board

STEP 19
Attach the P12 Lower Back Cabinet Board onto the P7 / P8 Back Legs using pilot holes and the H1 Phillips Round Screws as shown in FIGURE 19.
Tighten, but DO NOT strip out H1 Screws.
NOTE: All male/ female connectors must be turned correctly in order to plug into each other.

PARTS REQUIRED

• 1pc – P11 Upper Back Cabinet Board
• 1pc – A1 A/C Adapter
• 6pcs – H1 Phillips Round Head Screw
• 2pcs – H2 Phillips Round Head Screw

STEP 20
Attach the P11 Upper Back Cabinet Board onto the Back Leg Cabinet using pilot holes and the H1 and H2 Phillips Round Screws as shown in FIGURE 20.
Tighten, but DO NOT strip out H1, and H3 Screws.
Plug the A1 A/C Adapter into the back side of the P29 Electronic Scorer Do not allow the A/C Adapter cord to be a trip hazard.
Do not allow the A/C Adapter cord to be a trip hazard.

PARTS REQUIRED

• 1pc – P31 Left Plastic Trim Strip
• 1pc – P32 Right Plastic Trim Strip
• 2pcs – P6 Top Rail Plastic Corner Cap
• 14pcs – H3 Phillips Round Head Screw

STEP 21
Attach the P31 / 32 Plastic Trim Strips onto the Cabinet using pilot holes and the H3 Phillips Round Screws as shown in FIGURE 21.
Attach the P6 Top Rail Plastic Corner Caps onto the Front Legs using pilot holes and the H3 Phillips Round Screws as shown in FIGURE 21.
Tighten, but DO NOT strip out H3 Screws.

ELECTRONIC CONNECTIONS

NOTE: All male/ female connectors must be turned correctly in order to plug into each other. Connections 1,2,3,4 are all made by the customer.

Congratulations! You have now assembled your game table. Please note the Care and Use instructions below to ensure many years of trouble-free use of your game table.
CARE AND USE OF YOUR TABLE

1. Use spray furniture polish to clean all exterior surfaces of your game table and on the playfield( but not the plexiglass which requires an acrylic cleaner/polish).
2. Use only a suitable 120v AC household outlet, and ensure the cord is not a trip hazard.
3. This product is intended for INDOOR use only.
4. DO NOT sit, climb or lean on the table.
5. DO NOT drag the table when moving it. This will damage the legs.
6. DO NOT set drinks on the table.
7. The purchase of a table cover will both protect and help keep clean the entire top of the game table.

PRODUCT PARTS LIST FOR MODEL #AL4100

P11
P12| AL4100HLP11 AL4100HLP12| Upper Back Cabinet Board
Lower Back Cabinet Board| 1
1
P13| AL4100HLP13| Left Side Apron| 1
P14| AL410OHLP14| Right Side Apron| 1
P15| AL4100HLP15| Left Top Rail with Control Switch and Wiring| 1
P16| AL4100HLP16| Right Top Rail| 1
P17| AL4100HLP17| Left Leg (assembled with P2)| 1
P18| AL4100HLP18| Right Leg (assembled with P3)| 1
P19| AL4100HLP19| Playfield with End Ramp| 1
P20| AL4100HLP20| Wooden Support Brace (packed with P30)| 1
---|---|---|---
P21|  AL4100HLP21| Connecting Board| 2
P22| AL4100HLP22| Goal Box Bottom Board| 1
P23| AL4100HLP23| Metal Connection Plate| 16
P24| AL4100HLP24| Middle Support Board| 2
P25| AL4100HLP25| End Support Board| 1
P26|  AL4100HLP26| Plastic Ball Return| 2
P27|  AL4100HLP27| Clear Plexiglass with Protective Coating on Both Sides| 1
P28|  AL4100HLP28| Lower Front Cabinet Board| 1
P29|  AL4100HLP29| Electronic Scorer| 1
P30| AL4100HLP30| Black Plastic “L” Bracket| 6
P31|  AL4100HLP31| Right Plastic Trim Strip| 1
P32| AL4100HLP32| Left Plastic Trim Strip| 1
P33|  AL4100HLP33| Plastic Connector (Playfield to Front Leg)| 1
A1|  AL4100HLA1| A/C Adapter| 1
A2| AL4100HLA2| Ball| 4
C1|  AL4100HLC1| ON / OFF Switch| 1
C2| AL4100HLC2| Led Strip| 2
C3| AL4100HLC3| Scoring Sensor| 7
C4|  AL4100HLC4| 3.5mm x 12mm Phillips Round Head Screw| 14
K1|  AL4100HLK1| Hardware Kit| 1
M1|  AL4100HLM1| Instruction Manual| 1

90-DAY LIMITED WARRANTY

This customer warranty extends to the original owner, on the purchase of any ESCALADE SPORTS
Product (hereinafter referred as the “Product”).
WARRANTY DURATION:
This Product is warranted to the original owner, for a period of 90 days from the original purchase.
WARRANTY COVERAGE:
ESCALADE SPORTS warrants to the original owner, this product to be free
from defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT, OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORKMANSHIP.
WARRANTY REPLACEMENT:
During the above 90-day warranty period, ESCALADE SPORTS shall
provide replacement components or replace them with a comparable product of our choosing. If the product is defective under normal use and proper care, please contact our Customer Service Dept.
1-888-996-2729 / Customer Service Dept.
Or Write us at Escalade® Sports, Inc. – P.O. Box 889, Evansville, IN 47706
Attn: Customer Service Dept.
Or E-mail us at:customerservice@escaladesports.com
Other than shipping requirements no charge will be made for such replacement of in-warranty Products.
WARRANTY DISCLAIMERS:
ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO THE ABOVE 90-DAY PERIOD. ESCALADE SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES:
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.

All Rights Reserved.
© 202 1 Escalade Sports
For Customer Service Call 1-888-996-2729

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>