Bebe Stars 390T Children’s and Infants Instruction Manual

Bebe Stars 390T Children’s and Infants Instruction Manual

IMPORTANT – READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.

Dear Customers,
Thank you for purchasing a Bebe Stars product. Our products have been designed for your child’s safety and comfort. The stroller is an ideal solution for those who value quality, modernity and functionality. The product meets the requirements of safety standard EN 1888-1,2:2018. Please read the manual carefully and follow its recommendations.

WARNING!
Never leave your child unattended. Before use make sure that all locking devices are turned on. To avoid injury, make sure your child is moved away when the product is being unfolded or folded. Do not allow children to play with the product. Before use check if the devices fixing the bassinet, seat or car seat are properly attached. This product is not suitable for running or skating. The product is designed to transport one child at a time with weight up to 22kgs. Maximum basket load 3 kg. Any additional load suspended from the stroller handles, under the backrest or on the sides will cause stability deterioration. The maximum permissible weight of a parent’s bag suspended on the stroller’s handles is 2 kg. Lift the front suspension when going up a curb or step. The brakes should be locked when the child is placed in or taken out of the stroller. Use only parts and accessories supplied or recommended by the manufacturer. Do not use other parts or accessories. Do not place the product near open flame or other heat sources.

The following applies to the bassinet: This product, in the form of a bassinet, is designed for children who cannot sit unaided, fall over or crawl using hands and knees. Maximum child weight – up to 9 kg. The bassinet must not be used as a child carrier. The bassinet handle is only designed for assemble and disassembly of the stroller frame. Do not insert an extra mattress apart from that supplied with the product.

The following applies to the stroller:
WARNING! This seat unit is not suitable for children under 6 months. Always use the restraint system. The product is intended for children from 6 months old to 22 kg.

The following applies to the car seat:
The product is intended for children from birth up to 87cm. If the seat is used together with the stroller, it does not replace a cradle or crib. For sleep, place the child in the bassinet, cradle or crib.

STROLLER PARTS

Stroller frame components (FIG.1)

1. Handle
2. Buttons to adjust the handle
3. a) Release button b) Folding lever
4. Frame slot a) Car seat adapters
5. Folded frame locking element
6. Brake
7. Rear wheels
8. Front wheel release button
9. Front wheels
10. Swivel wheels lock
11. Back wheel release button
    **Pushchair elements (FIG.2)

**

12. Backrest adjustment lever

13. Pushchair canopy detach button

14. Safety bar release button

15. Lever for releasing the seat from the frame

16. Seat and stroller frame connector

17. Footrest adjustment button

18. Safety bar

19. Leg cover

20. Rain cover
    Bassinet elements (FIG.3)

21. Bassinet carrying handle

22. Bassinet hood

23. Bassinet hood folding/unfolding button

24. Lever for releasing the bassinet from the frame

25. Bassinet and stroller frame connector

26. Mattress

27. Leg cover

28. Rain cover

UNFOLDING STROLLER FRAME



In order to unfold the frame, release the locking element (FIG. 4). Holding the handle, lift the frame (FIG. 5) until you hear a locking sound (FIG. 6)

WHEEL ASSEMBLY/DISASSEMBLY





Insert the front wheels in the slots on the front of the frame until you hear the locking sound (FIG. 7A). In order to remove the wheels, press the front wheel release button as shown in Figure 8. The stroller has a system of swivel front wheels with a possibility of locking for straight movement. To lock the wheel for straight movement, press the upper part of the lock (FIG. 9, movement A). In order to unlock, move the lock up (FIG. 9, movement B). Insert the rear wheels into the slots in the rear part of the frame until they lock, making sure that the flat surfaces of the axis of the slot have been set correctly (FIG. 10). To remove the rear wheel, press the release button (FIG.11).
NOTE! Before using the stroller make sure that all the wheels are properly installed.

ASSEMBLY INSTRUCTIONS & USAGE

**USE OF BRAKE

**
The stroller is equipped with a foot parking brake. Press the brake with your foot (FIG. 12.1). The brake is activated after you hear the sound of the lock. The brake is unlocked after moving the brake lock up (FIG. 12.2).

ASSEMBLY/DISASSEMBLY

**1 SEAT

**
When installing the seat on the stroller frame, stick the seat connector (A) in to the frame slot (B) (one on each side of the stroller) until you hear a click (FIG. 13.1). The seat may be mounted forward or rearward (FIG. 13.2). When removing the seat, press the lever for releasing the seat from the frame on the both sides (FIG. 14.1) and pull it up (FIG. 14.2). Leg cover should be mounted using the press studs on the outside of the canopy hinges. NOTE! Do not fold the stroller frame when the bassinet or the seat in its rear position is installed on it.

**11 CANOPY

NOTE!** INSTALL THE CANOPY BEFORE USING THE STROLLER Place the canopy in the guide in the stroller frame and make sure it is properly installed (FIG. 15.1). When removing the canopy, press the button on either side of the seat and remove the canopy (FIG. 15.2). When installing and removing the canopy remember about Velcro fasteners on the sides and the zip on the back of the backrest.

**III SAFETY BAR

**
When installing the safety bar, insert it in the appropriate guides in the seat frame until it clicks (FIG.16.1). To remove the part, press the bar release buttons on either side of the guide and remove the safety bar (FIG. 16.2).

SAFETY BELTS


Lock the safety belt (FIG. 17.1): insert the safety plug (A) into the safety socket (B) until it clicks into place. Adjust the ladder buckle (C) on the shoulder belt to make the harness fits snugly. Release the seat belt (FIG. 17.2): hold and press the top and bottom safety buckle seats (B) with your thumb and index finger. The harness fit can be.

SEAT POSITIONS

The seat has 4 positions: lying, 2x reclining and sitting, adjusted with backrest adjustment lever (FIG. 18.1).

PARENT HANDLE ADJUSTMENT

To adjust the bar, press the handle adjustment buttons on both sides and set it in the desired position (FIG.19).

**FOOTREST ADJUSTMENT

**
The position is changed by lifting the footrest (FIG. 20.1). In order to lower the footrest, press the footrest adjustment buttons on both sides (FIG. 20.2).

FOLDING THE STROLLER (FIG.21)

Make sure that the seat is positioned facing the direction of travel before folding the stroller. Fold the canopy. Simultaneously press the release button and pull both folding levers to yourself to fold the stroller. When the stroller is completely folded, the locking element will lock itself. In order to minimize the folded stroller dimensions, lower the footrest. In addition, set the backrest in the top position to facilitate frame folding.

STROLLER BASSINET




After removing the bassinet from the packaging, set the hood (FIG.22A). The hood can be folded using the bassinet hood folding and unfolding buttons on both sides of the bassinet (FIG.22B). Place the foot cover and attach it to the bassinet hood using the press studs (FIG. 23). The foot cover is equipped with an additional panel protecting from the wind. When the wind blows, it can be attached using a clamp (FIG. 24A). After folding, it must be fixed using clamp B (FIG. 24B). To adjust the bassinet backrest, take the foot cover off and remove the mattress (FIG. 25.1). Lift the plastic part of the backrest and place the metal element in position A or B (FIG. 25.2). Place the other end of the element in latches C (FIG. 25.3). Place the mattress and the foot cover (FIG. 25.4).

ATTACHING THE BASSINET TO THE STROLLER FRAME

NOTE! THE BASSINET CAN ONLY BE MOUNTED FACING BACKWARDS (the child faces the person pushina the stroller). When installing the bassinet on the stroller frame, stick the bassinet connector (A) in to the frame slots (B) (FIG. 26), one on each side of the stroller, until you hear a click. When removing the bassinet, press the lever for releasing the bassinet from the stroller frame (C) on both sides and pull up (FIG.26).

CAR SEAT ASSEMBLY ON STROLLER FRAME

Place the adapters on both sides of the seat (FIG. 27). When installing the car seat on the stroller frame, stick them in the designed slots, one on each side of the stroller until you hear a distinctive click. Removing the seat press the buttons on both sides and pull up.
The car seat must always be fitted in such a way that the child should face the carer.

CARE & MAINTENANCE

CARE AND MAINTENANCE
The buyer is responsible for proper installation of all functional elements as well as for carrying out all required maintenance and adjustments in order to keep the stroller in good technical condition. The stroller must be periodically checked for potential problems. Significant measures to be applied to ensure the child’s safety and prevent shortening of the product life have been presented below:

• Check the coherence and safety of all connections.
• Check all wheel locking equipment and tyres. If necessary, replace or repair.
• Check if all safety devices work properly, particularly the main and additional fasteners that should move freely at any time. Please stop using the stroller if there are doubts as to its proper use or a suspicion of any danger. Use only the spare parts supplied or recommended by the manufacturer. If the wheels squeak, apply a thin layer of silicone. Do not use oil or grease based products as they attract dirt, which makes it difficult for the wheels to move.

CLEANING
If the elements of the stroller chassis have been exposed to saltwater, rinse with tap water as soon as possible. Do not wash. Clean the product gently with a damp cloth and a mild detergent.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>