XFANIC A3003B Sentry Wireless Lavalier Mic Instruction Manual
- June 1, 2024
- XFANIC
Table of Contents
XFANIC A3003B Sentry Wireless Lavalier Mic
PACKAGE CONTENTS
- 2x Transmitter (Microphone)
- 1x Receiver
- 2x Fur Windshield
- 2x 3.5mm Lapel Clip on Microphone
- 1x TRS to TRS 3.5mm Cable
- 1x USB-C to USB-C OTG Cable
- 1x TRS to TRRS 3.5mm Cable
- 1x USB-A to 3*USB-C Cable
- 1x Storage Case
- 1x User Manual
DEVICE DESCRIPTION
TX (MICROPHONE)
TX BUTTON FUNCTIONALITY
TX SCREEN ICON (TRANSMITTER)
RX (RECEIVER)
RX BUTTON FUNCTIONALITY
RX SCREEN ICON (RECEIVER)
HOW DOES IT WORK
INSTRUCTIONS
- Long press the power button to power each device, and then the transmitter and receiver will start pairing automatically. The icons on the screen will be constantly lit for the initial period.
- Clip the transmitter (TX) onto your collar or connect it with an external 3.5mm lapel microphone.
- Fix the receiver (RX) on the hot shoe of the camera or near another recording device.
- Connect the receiver (RX) with the audio input port of the recording device via the 3.5mm audio cable. Please verify if TRS or TRRS is needed for your device.
SPECIFICATIONS
- P/N 44695
- Product Type 2.4GHz Digital Wireless Microphone
- Sampling Rate 48KHz
- Microphone Direction Omni Directional
- Sensitivity -36dB
- SIN 70dB
- Frequency Response 20Hz~20KHz
- Connecting Distance max 50M
- Battery Capacity 180mAh
- Charging Port USB-C (5V Input)
- Tx/Rx Ch rging Time: 80 Minutes
- Tx Battery Endur nce Time: 7.5H
- Rx B ttery Endur nce Time: 5H
USER INTERFACE
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Modifying the equipment without Monoprice’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radio Notice for FCC
Caution
This FCC Part 15 radio device operates on a non-interference basis with other
devices operating at this frequency. Any changes or modifications to said
product not expressly approved by Monoprice, including the use of non-approved
antennas, could void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Radio Notice for ISED Canada:
This device complies with ISED Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Radio Frequency Exposure
This device meets the ISED Canada requirements for exposure to radio waves and
is designed and manufactured not to exceed the emission limits for exposure to
radiofrequency (RF) energy. To comply with Canada RF exposure compliance
requirements, this device must not be co-located or operating in conjunction
with any other antenna or transmitter.
Notice for ISED Canada:
CAN ICES-3 (B)/NMB-3(B)
Contact Information
Need Help? We’re here for you!
- Contact us: www.monoprice.com/contactus.
- Product pictures are for reference only.
Specifications described herein are subject to change without prior notification. Monoprice™ and all Monoprice logos are trademarks of Monoprice Inc.
Copyright © 2023 Monoprice, Inc. All rights reserved.
Monoprice, Inc.
- 1 Pointe Drive, Suite 400 Brea, CA 92821 – USA
- www.monoprice.com
- Tel. 877.271.2592