Luceco LBH154AME-02 ATLAS Exterior Metal Eyelid Bulkhead Cover Instruction Manual
- June 13, 2024
- LUCECO
Table of Contents
Installation & Operating Instructions
Die-cast accessories for LED IP65 Bulkhead
PART CODE: LBH154AMP/ LBH154AME/LBH154AMS/ LBH154AMG
LBH154AME-02 ATLAS Exterior Metal Eyelid Bulkhead Cover
NOTE – To comply with regulations, installation must be carried out
by suitably qualified competent person and in accordance with the current IEE
Wiring Regulations (BS7671) and Building Regulations. A copy of the
instructions must be left for the user/maintenance engineer for future
reference.
For non-UK, please refer/consult local requirements
ENSURE ELECTRICAL SUPPLY IS DISCONNECTED/ ISOLATED BEFORE COMMENCING
INSTALLATION
For electrical Installation please see separate LBH154K instructions.
- Suitable for use with luceco LBH154K, LBH154K3M, LBH154KMW, LBH154KMW3M.only.
- This product must be disconnected before insulation resistance testing of the lighting circuit.
- Check for electrical cables and pipes before installation.
- To maintain the IP65 rating of the bulkhead, a suitable 20mm cable gland should be used in conjunction with rubber insulated cable to ensure the supply cable is sealed in the gland. Failure to use a gland and/or rubber insulated cable may result in water ingress.
INSTALLATION
-
The bulkhead accessory is only suitable for surface mounting (wall or ceiling)
-
Surface mounted options may use rear cable entry for flush mounting or there is facility for surface conduit ‘besa’ box mounting or side conduit entry
-
On the LBH154K, remove the following: Bezel and diffuser by twisting anti-clowise as shown (fig 1) Rear trim)
-
If using side entry, remove the blank cover from the desired side of the cast base as shown (fig 2)
-
Insert white blank cover and re-fit screws for each remove cable entry blank.
-
Insert the LBH154K body into the base, ensure the mounting surface is suitable for installation. Once mounting points are decided, drill out mounting holes and any cable entry points needed.
-
Fit diffuser and cast front, tighten 4 screws until tight to ensure IP65 rating (fig 3)
-
If anti-tamper screws are required, use LBH154ATK (sold separately)
United Kingdom Warranty
For other territories and for further information, please see
www.luceco.com for details
Products are protected by guarantee for a period of 3 year warranty, from date
of purchase against defects in material and workmanship (unless otherwise
stated). Should a product fail to perform as described within the warranty
period it will be repaired or replaced with the same or equivalent product by
Luceco, free of charge provided that you: (1) return the product to us with
shipping charge prepaid, (2) provide us with proof of the original date of
purchase and (3) quote our return authorization number. Repaired or replaced
products will be returned to you with shipping charges prepaid. Replacement
products may be refurbished or contain refurbished materials. If in our sole
discretion, we are unable to repair or replace a defective product, we will
refund the purchase price of the product.
This warranty will not apply if in our judgment, the product fails due to
damage in shipment, handling, storage, accident, abuse or misuse, or if it has
been used in a manner not conforming to our product instructions, has been
modified in any way, or has any serial number removed or defaced. Repair or
attempted repair will void this warranty. Our maximum liability under the
terms of this warranty is limited to the purchase price of the product covered
by the warranty.
The warranty is given under English Law. If any part of this warranty is
deemed unenforceable (including any provision in which we exclude our
liability to you) the enforceability of any other parts of the warranty will
not be affected. These terms do not reduce your statutory rights.
For Non-UK please contact Local Luceco Office for details. THESE TERMS AND
CONDITIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
Eventually, you may want to replace this fitting;
Environmental Protection W.E.E.E (Wheelie Bin Symbol for EU ONLY)
This symbol is known as the “crossed-out” wheelie Bin Symbol”. When this
symbol is marked on a product or battery, It means that it should not be
disposed of with your general household waste. Some chemicals contained within
electrical/electronic products or batteries can be harmful to health and the
environment. Only dispose of electrical/electronic/battery items in separate
collection schemes, which cater for the recovery and recycling of materials
contained within. Your co-operation is vital to ensure the success of these
schemes and for the protection of the environment.
Tech Help Line
UK – 0330 0249 279
Non UK – +44 (0)1952 238 100
Supplied by LUCECO
Stafford Park 1, Telford, Shropshire,
England, TF3 3BD
Visit our website at www.luceco.com
Servicio de asistencia telefónica
UK – 0330 0249 279
Non UK – +34 93 829 55 74
(EU) Luceco SE
C/ Bobinadora 1-5
08302 Matarό Spain
Visite nuestra web en www.luceco.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>