Ampeg Opto Comp Analog Optical Compressor User Guide
- June 1, 2024
- ampeg
Table of Contents
- Ampeg Opto Comp Analog Optical Compressor
- Product Information
- Product Usage Instructions
- What’s in the Box
- Hookup Diagrams
- PA/Recording Setup
- Front, Rear, Side and Bottom Panel Descriptions
- Getting Started
- WARRANTY AND SUPPORT
- FAQ
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Ampeg Opto Comp Analog Optical Compressor
Product Information
Specifications
- Signal-to-Noise Ratio (100 Hz @ 1.00V RMS)
- Maximum Gain: 82 dB +14 dB
- Power Requirements:
- Internal: 9V Battery
- External: 9V DC, 25mA
- Size (H x W x D): 2.2 x 2.6 x 4.5 in / 56 x 66 x 114 mm
- Weight: 0.6 lb / 0.3 kg
Product Usage Instructions
Getting Started
- Read and understand the included Important Safety Instructions.
- Make all initial connections with the power switches OFF on all equipment. Ensure Master Volume, Level, and Gain controls are at minimum.
- Insert a 9V battery or connect an optional AC/DC power supply as per voltage specifications on the rear panel.
- Connect an instrument to the Input jack using a 1/4 (shielded) instrument cable.
- While playing the instrument, adjust the Output Level knob to the desired level.
- Adjust the Compression and Release knobs to your preference.
What’s in the Box
Opto Comp Analog Optical Compressor Pedal, Quick Start Guide.
Hookup Diagrams
PA/Recording Setup
Front, Rear, Side and Bottom Panel Descriptions
- Input: Connect a passive or active instrument to this Input jack.
- Output: Feeds the signal to an external power amplifier, mixer, or recording setup.
- On/Off Switch: Turns the pedal on/off. The LED indicates the on/off status.
- Compression: Controls the overall amount of compression applied to a signal.
- Release: Determines how long it takes for the compressor to end gain reduction.
- Output Level: Adjusts the overall output level.
- Gain Reduction LED: This LED increases in brightness as gain reduction increases.
- Power: Input socket for optional AC/DC power supply.
- Battery (not included): Provides 9V of power (accessible by removing the four screws on the bottom panel).
- Pad: Reduces input level by 15 dB.
Getting Started
- Read and understand the included “Important Safety Instructions.”
- Make all initial connections with the power switches OFF on all equipment. Make sure the Master Volume, Level and Gain controls are all the way down.
- Insert a 9V battery or connect an optional AC/DC power supply. The Opto Comp Compressor may accept the appropriate voltage as indicated on the rear panel.
- Connect an instrument to the Input jack with a 1/4″ (shielded) instrument cable.
- While playing the instrument, adjust the Output Level knob to the preferred level.
- Adjust the Compression and Release knobs to taste.
WARRANTY AND SUPPORT
Visit WWW.AMPEG.COM to…..
- Identify warranty coverage provided in your local market. Please keep your sales receipt in a safe place.
- retrieve a full-version, printable OWNER’S MANUAL (English only) for your product.
- REGISTER your product.
- CONTACT Technical Support, or call 818-575-3600.
www.ampeg.com
Yamaha Guitar Group, Inc.
26580 Agoura Road, Calabasas, CA 91302-1921 USA Part No. 40-00-0433 Rev. A
© 2019 Yamaha Guitar Group, Inc. All rights reserved.
Ampeg and the Ampeg logo are trademarks or registered trademarks of Yamaha
Guitar Group, Inc. in the U.S. and/or other jurisdictions.
FAQ
Q: Where can I find warranty and support information?
A: Visit www.ampeg.com for warranty coverage details, owner’s manual, product registration, or technical support. You can also contact me at 818-575-3600.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>