Ampeg SVT-810E AV Dual Bass Cabinet Owner’s Manual

Ampeg SVT-810E AV Dual Bass Cabinet

Specifications

• Power Handling: 800W RMS (Mono), 400W RMS (Dual)
• Impedance: 4 Ohms (Mono), 8 Ohms (Dual)
• Designed in the USA | Made in China
• Serial Number: Upper 4×10-Dual Mode Only, Lower 4×10-Dual Mode Only

Product Information

Your Ampeg SVT-810E/AV Dual Bass Cabinet is a high-quality speaker cabinet suitable for all sizes of venues. The cabinet can be split into two isolated 8-ohm, 4×10 cabinets via the jack plate connections, allowing each cabinet to be driven by a separate amplifier. It features an industrial-strength grip bar, heavy-duty recessed wheels, and skid rails for protection during transportation. The cabinet is available in two grille cloth options: Classic black and white (SVT-810E) or Anniversary blue and silver (SVT-810AV).

Usage Instructions

Setting Up the Cabinet

• Place the cabinet in your desired location with the help of the grip bar and wheels.
• Use the skid rails to protect the cabinet while loading and unloading.

Connecting Amplifiers

• The cabinet operates in Dual Mode when a connector is inserted into the 1/4 Upper 4×10 Dual Mode input jack. Otherwise, it operates in single 8×10 Mono Mode.
• Use appropriate speaker cables to connect your amplifier to the cabinet based on your setup.

Playing Music

• Once the cabinet is connected to your amplifier, adjust the volume and tone settings on your amplifier to achieve the desired sound output.
• Start playing your bass guitar or any audio source through the cabinet.

FAQ

Q: Can I use the SVT-810E/AV with any bass amplifier?

A: Yes, you can use the SVT-810E/AV with any bass amplifier as long as it matches the impedance requirements of the cabinet.

Q: How do I switch between Dual Mode and Mono Mode on the cabinet?

A: Inserting a connector into the 1/4 Upper 4×10 Dual Mode input jack activates Dual Mode while leaving it empty activates Mono Mode.

What’s in the Box

• SVT®-810E or SVT-810AV Speaker Cabinet, Quick Start Guide.

Introduction

• Your Ampeg SVT-810E/AV Dual Bass Cabinet is a high-quality speaker cabinet suitable for all sizes of venues. The SVT-810E/AV can be “split” into two isolated 8-ohm, 4×10 cabinets via the backplate connections.
• This allows each cabinet to be driven by a separate amplifier.
• The cabinet features an industrial-strength grip bar and heavy-duty recessed wheels. Skid rails are placed on the back of the enclosure to protect it while loading in and out of venues and vehicles. (Place a foot against one of the rails to tilt the cabinet back.)
• Note that this cabinet is available in two different grille cloth options: Classic black and white (SVT-810E) or Anniversary blue and silver (SVT-810AV)—All specs and features are otherwise identical.
• The Speakon® and 1/4″ jacks are wired in parallel, allowing easy daisy chaining from one speaker to another. Each of the jacks may be used as an input or a through connection. Speakon connectors are recognized as the standard for professional installations, assuring a secure, permanent connection that won’t corrode, vibrate loose, or be easily tampered with. The 1/4″ jacks are convenient. However, the Speakon jacks are recommended when using power amplifiers over 150 watts, for permanent installations, or the “first” speaker among many daisy-chained speakers.
• To get the most out of your new Ampeg speaker cabinet, please fully read this Owner’s Manual, as well as the Important Safety Instructions included with your cabinet before you begin playing.
• And thank you for choosing Ampeg.

Jackplate

1. 1/4″ Upper 4×10 Dual Mode Input Jack*
2. 1/4″ Lower 4×10 Dual Mode or Mono Mode Input / Output Jacks
3. Speakon Lower 4×10 Dual Mode or Mono Mode Input / Output Jacks
   • The cabinet operates in Dual Mode whenever a connector is inserted into the 1/4″ Upper 4×10 Dual Mode input jack [1].
   • Otherwise, the cabinet operates in the single 8×10 Mono Mode.

Speakon to 1/4″ Wiring Diagram

Suggested Hookup Diagrams

• In the example above, a speaker cable with Speakon ends connects from the speaker output of the amplifier to one of the Speakon inputs of the Ampeg SVT-810E/AV cabinet.
• Alternatively, a speaker cable with 1/4″ ends can be used to connect from an amplifier’s 1/4″ speaker output to one of the Lower 4×10 Dual Mode/Mono 1/4″ inputs of the SVT-810E/AV.
• This configuration allows the amplifier to drive all 8×10 speakers.
• WARNING: Always use good quality (non-shielded) speaker cables. Never use (shielded) instrument cables to connect speakers to an amplifier.
• Also, do not use both cable routes in the examples listed above.
• Use one route or the other, but never both simultaneously!
• In the example above, one speaker cable with 1/4″ ends connects from the speaker output of the amplifier to the Upper 4×10 Dual Mode 1/4″ input of the Ampeg SVT-810E/AV cabinet. An additional speaker cable with 1/4″ ends connects from the speaker output of another amplifier to one of the Lower 4×10 Dual Mode 1/4″ inputs of the SVT-810E/AV. This configuration allows two amplifiers (or the discrete two output channels of a stereo amplifier) to separately drive each 4×10 section of the full cabinet.
• WARNING: Always use good quality (non-shielded) speaker cables. Never use (shielded) instrument cables to connect speakers to an amplifier.

Technical Specifications

• The SVT-810E/AV is covered with a durable fabric-backed vinyl material. Clean with a dry, lint-free cloth. Never spray cleaning agents on the SVT-810E/AV. Avoid abrasive cleansers which would damage the finish.
• Ampeg continually develops new products and improves upon existing ones. For this reason, the specifications and information in this manual are subject to change without notice.
• CAUTION: THIS SPEAKER IS CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED
• EXPOSURE TO HIGH SOUND PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS.
• USER CAUTION IS ADVISED. AND EAR PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.

Warranty and Support

VisitWWW.AMPEG.COM to…

1. Identify warranty coverage provided in your local market. Please keep your sales receipt in a safe place.
2. REGISTER your product.
3. CONTACT Technical Support, or call 818-575-3600.

• www.ampeg.com
• Yamaha Guitar Group, Inc.
• 26580 Agoura Road, Calabasas, CA 91302-1921 USA Rev. A
• © 2019 Yamaha Guitar Group, Inc. All rights reserved.
• Ampeg, the Ampeg logo, and SVT are trademarks or registered trademarks of Yamaha Guitar Group, Inc. in the U.S. and/or other jurisdictions. Speakon is a registered trademark of Neutrik AG Corporation.

References

• Ampeg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>