Ampeg SVT-CL 300 Watt Tube Bass Head Sweetwater User Guide

June 1, 2024
ampeg

Ampeg LOGO SVT-CL, SVT-VR, V-4B
Quick Start GuideAmpeg SVT CL 300 Watt Tube Bass Head
Sweetwater

What’s in the Box

  • SVT® -CL, SVT-VR, or V-4B Amplifier
  • Power Cable
  • Quick Start Guide

Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifiers:
Ampeg SVT-CL, SVT-VR, and V-4B
Responsible Party – U.S. Contact Information:
Yamaha Guitar Group, Inc.
26580 Agoura Road
Calabasas, CA 91302-1921
818-575-3600
https://ampeg.com/
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

There are various types of fuses, and replacing them with different types may cause malfunction, electric shock, or fire. Be sure to confirm you are replacing the correct fuse with electrical rating and specifications.
Each number and symbol represent the following:
Example: T3AL250V

① T,  ②●A, ③ L, and ④ ■V are shown below.
① Symbol indicating relative fusing time / current characteristics T: Time lag type, F: Fast-acting type.
②●A: Rated current
③ Symbol indicating the blocking capacity L: Low cutoff capacity, E: Medium cutoff capacity, H: High cutoff capacity.
④■V: Rated voltage

© 2021 Yamaha Guitar Group, Inc. All rights reserved.
Ampeg, the Ampeg logo, and SVT are trademarks or registered trademarks of Yamaha Guitar Group, Inc. in the U.S. and/or other jurisdictions. Speakon is a registered trademark of Neutrik AG Corporation.

Hookup Diagrams

Standard Setup

Ampeg SVT CL 300 Watt Tube Bass Head Sweetwater - Standard
Setup

Parallel Setup

Ampeg SVT CL 300 Watt Tube Bass Head Sweetwater - Parallel
Setup

Daisy Chaining

Ampeg SVT CL 300 Watt Tube Bass Head Sweetwater - Daisy
Chaining

Note: Use same impedance cabinets in parallel setups and when daisy- chaining

Front & Rear Panels

Ampeg SVT CL 300 Watt Tube Bass Head Sweetwater - Front & Rear
Panels

Front & Rear Panel Descriptions

  1. 0 dB Input: Connect a passive instrument to this Input jack.
  2. –15 dB Input: Connect an active instrument to this Input jack.
  3. 1/4″ Inputs: Connect an instrument to one of these four Input jacks.
  4. Gain: Varies the intensity of the signal sent to the preamplifier.
  5. Ultra Hi: Boosts the high frequencies.
  6. Ultra Lo: Boosts the low frequencies.
  7. EQ: Boost or cut the level at certain frequencies to enhance the sound.
  8. Master/Volume: Controls the overall output level.
  9. Standby/Power/Fault LED: Multi-function LED illuminates red in Standby mode and green when powered on. It flashes between red and green when the amp detects a fault (SVT-CL and SVT-VR only).
  10. Standby Switch: Turns the Standby on and off.
  11. Power Switch: Turns the Power on and off.
  12. Power Connector: Input socket for power cable.
  13. Fuse: Overload and AC line surge protection.
  14. Polarity Switch: Removes electrical buzz.
  15. Bias/Balance: Controls and LEDs for user biasing.
  16. Ext Amp Out: Feed another amp from this unit’s preamp.
  17. Balanced Out: Feeds the signal from the Power Amp Input to an external power amplifier, mixer or recording setup.
  18. Level: Adjusts the signal level at the Balanced Output jack.
  19. Pre (Ch. 1)/Post Switch: Set the Balanced Output jack to Pre-EQ (disengaged) or Post-EQ (engaged).
  20. Lift/Gnd: Connects the ground connection at the Balanced Output jack.
  21. Preamp Out: Feeds an external amplifier or powered speaker.
  22. Power Amp In: Bypasses the internal preamp.
  23. Impedance Selector: Match the output impedance of the amp to the speaker(s).
  24. Speaker Outputs: 1/4″ TS / Speakon® outputs for connecting speakers.

Getting Started

  1. Read and understand the included “Important Safety Instructions.”
  2. Make sure the Power and Standby switches are off before making any connections.
  3. Push the line cord securely into the amplifier’s IEC connector and plug the other end into a grounded AC outlet. The amplifier may accept the appropriate voltage as indicated near the IEC connector.
  4. Connect an instrument to the amplifier’s Input jack with a (shielded) 1/4” instrument cable. Connect speaker cables to speaker cabinets with (non-shielded) speaker cable with Speakon or 1/4″ TS ends.
  5. With the Gain and Master/Volume controls fully off, turn the Power switch on. The Power LED will illuminate. Wait 30 seconds.
  6. Turn the Standby switch on.
  7. While playing the instrument, adjust the Gain and Master/Volume knobs to the preferred level.
  8. Adjust the EQ knobs and switches to taste.

Technical Specifications

| SVT-CL| SVT-VR| V-4B
---|---|---|---
Preamp Tubes| 2 x 12AX7| 3 x 12AX7, 2 x 12AU7| 2 x 12AX7
Driver Tubes| 1 x 12AX7, 2 x 12AU7| 1 x 12AX7, 2 x 12AU7| 1 x 12AX7, 1 x 12AU7
Power Amp Tubes| 6 x 6550| 6 x 6550| 4 x 6L6GC
Output Power Rating| 300W RMS @ <3% THD
@ 2  / 4Ω| 300W RMS @ <5% THD
@ 2  / 4Ω| 100W @ 8% THD+N
@ 2  / 4  / 8 Ω
Signal-to-Noise Ratio
(20 Hz – 20 kHz)| 80 dB| 75 dB| 80 dB
Maximum Gain| 67 dB @ 1 kHz
–3 dB @ 40 Hz & 15 kHz| 78 dB @ 1 kHz
–3 dB @ 20 Hz & 15 kHz| 64 dB @ 1 kHz
–3 dB @ 14 Hz & 15 kHz
Power Requirements| 120V AC, 50–60 Hz, 460W
100V AC, 50–60 Hz, 460W
220–240V AC, 50–60 Hz, 460W| 120V AC, 50–60 Hz, 400W
100V AC, 50–60 Hz, 400W
220–240V AC, 50–60 Hz, 400W| 120V AC, 60 Hz, 200W
100V AC, 50–60 Hz, 200W
220–240V AC, 50–60 Hz, 200W
Size (H x W x D)| 11.5 x 24.0 x 13.0 in
292 x 610 x 330 mm| 11.5 x 24.0 x 12.75 in
292 x 610 x 324 mm| 10.8 x 23.8 x 11 in
275 x 604 x 280 mm
Weight| 80 lb
36.3 kg| 85 lb
38.6 kg| 41 lb
18.6 kg

All specifications subject to change.

WARRANTY AND SUPPORT

Visit WWW.AMPEG.COM to…

  1. …identify WARRANTY coverage provided in your local market. Please keep your sales receipt in a safe place.
  2. …retrieve a full-version, printable OWNER’S MANUAL (English only) for your product.
  3. …REGISTER your product.
  4. …CONTACT Technical Support, or call 818-575-3600.

Ampeg LOGO www.ampeg.com
Yamaha Guitar Group, Inc.
26580 Agoura Road, Calabasas, CA 91302-1921 USA
Part No. 40-00-0534 Rev. C

Documents / Resources

| Ampeg SVT-CL 300 Watt Tube Bass Head Sweetwater [pdf] User Guide
SVT-CL 300 Watt Tube Bass Head Sweetwater, SVT-CL, 300 Watt Tube Bass Head Sweetwater, Tube Bass Head Sweetwater, Bass Head Sweetwater, Head Sweetwater
---|---
| Ampeg SVT-CL 300 Watt Tube Bass Head [pdf] User Guide
SVT-CL 300 Watt Tube Bass Head, SVT-CL, 300 Watt Tube Bass Head, Tube Bass Head, Bass Head, Head

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals