nordlux ALEC IP44 LED Spot Alec White 6.1W Instruction Manual
- June 1, 2024
- nordlux
Table of Contents
nordlux ALEC IP44 LED Spot Alec White 6.1W
Product Specifications
- Operating Voltage: 100-240V
- IP Rating: IP44
- Maximum Inter-connected Units: 15pcs
- Dimensions: 79-83mm (L) x 73-79mm (W) x 68mm (H)
- Cable Length: 225cm
- Installation: Indoor Use Only
Product Usage Instructions
Installation:
- Before installation, ensure the power is switched off.
- Consult a local electrician for specific installation requirements, especially for bathroom installations.
- Connect the light fixture following the provided cable length guidelines.
- Ensure proper mounting and secure the fixture in place.
Adjusting Brightness/Memory Function:
To switch between brightness levels and activate the memory function:
- Quickly toggle between brightness levels (100%, 50%, night/ambience) within 4 seconds.
- If a desired brightness level is held for more than 6 seconds, it will be memorized.
- To recall the memorized setting, switch to the next level within 6 seconds.
Power On/Off Sequence:
To turn the light on or off:
- Toggle the switch 5 times rapidly to turn all units off/on.
- For individual units, use the ON/OFF switch accordingly.
Frequently Asked Questions:
-
Q: Can this light fixture be used outdoors?
A: No, this product is designated for indoor use only due to its IP20 rating. -
Q: What is the maximum number of units that can be connected together?
A: The maximum number of inter-connected units is limited to 15pcs for optimal performance and safety. -
Q: How do I reset the memory function?
A: To reset the memory function, switch off the power for at least 10 seconds and then follow the normal usage instructions.
INSTALLATION
DIMENSION
WIRING
Adjusting Brightness/Memory function
You switch easily from one to the other functionality (100%-50%-night/ambience
light) by switching short and less than 4 seconds between each step. If you
lit your preferred position for longer than 6 seconds and also wait more than
6 seconds between 2 switches, your last position will be memorized which means
by the next short switch, the memorized position will be lit.
Reset function
If you use more than 1 spot in the same room and you want to synchronize the
spot or you notice that the downlighters are desynchronized, you have to RESET
the different downlighters. How are you? You switch off all spots and you wait
for at least 6 seconds, then you switch on and off 5 times fast, let’s say all
5 switches in less than 5 seconds. After the 5 times on/off you switch on
again. In that way all spots must be now in the position of 100% in the inner
circle, synchronized again. If not, please repeat it.
FEATURES
- Protected against solid objects with a diameter of 1.0 mm or more. Protected against contact with dangerous parts with wires, etc.
- IPX4: Raindrops falling from any angle will not affect the function/safety of the lamp
- The mounting instruction must not be discarded.
- IMPORTANT! Always shut off power to the circuit before starting installation work. In some countries, electrical installation work may only be carried out by an authorized electrical contractor. Contact your local electricity authority for advice.The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced
- Disposal of waste equipment by users in private households in the European Union. This symbol indicates that this product must not be disposed of with your other household waste. Electrical and electronic equipment contain substances that may cause damage to human health and the environment if not recycled correctly. It is your responsibility to hand over to a designated collection point for recycling of waste electrical and electronic equipment. When handing over for correct recycling you help to prevent these products from straining nature and environment unnecessarily and to protect human health. For more information regarding correct disposal, please contact your local city office, your household waste disposal service or the store where you purchased this product.
- Luminaires are not suitable for covering with thermally insulation material.
- The lamp is only suitable for connecting directly to the mains.
- Class II: The lamp is double-insulated and does not need to be connected to the yellow/green earth wire.
- For indoor use only.
- We recommend the use of a 90° C temperature-resistant cable.
www.nordlux.com
Nordlux A/S • Ostre Havnegade 34 • DK-9000 Aalborg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>