White Mulberry ‎WM-SEH04P-BK Motorized Height Adjustable Desk User Manual

White Mulberry ‎WM-SEH04P-BK Motorized Height Adjustable Desk

Symbols

• Desk top Dimensions: 120cm
• 3 Height Position Memory
• Vertical Range: 72-118cm

| | | | CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY
---|---|---|---|---
Power Input 100V-240V| Speed 20 mm/s| Motion Noise ＜55dB| Load Capability 154 lbs / 70 kgs

Component List

1. Right Table Leg (x1)
   

2. Left Table Leg (x1)
   

3. Leg Base (x2)
   

4. Transmission rod (x1)
   

5. Control Panel (x1)

6. Power (x1)
   

7. Side Plates (x2)
   

8. Crossbar (x1)
   

9. Tabletop (x1)
   

10. Power cord (x1)
    

Hardware List

• Screws M6×8mm (x8)

• Screws M5×15mm (x10)

• Screws M6×35mm (x8)
  

• Screws M4×12mm (x2)

• Allen Key S=2mm (x1)
  

• Allen Key S=5mm (x1)
  

• Cable Clip (x2)

Spare Parts

• A M6×8mm (x1)

• B M5×15mm (x2)

• C M6×35mm (x1)

• D M4×12mm (x1)

Assembly Instruction

Controller Introduction

 LED Display: Press any key once to wake up the display
 Press the 1 or 2 or 3 button, the desk will move to the height that was previously set for that button.
 Long press the button to raise the desk continually, and desk will stop when the button was released or at the max height (46.5″ / 118cm)
Long press the button to lower the desk continually, and desk will stop when the button was released or at the lowest height (28.3″ / 72cm)
Memory button setting: adjust desk to the height you prefer, then long press the button  1 or 2 or 3 until LED display shows H1 or H2 or H3 and flashes for about 3 seconds, then LED display shows the height you already set, and height memory setting is done.
Reset Press and hold the button for 5 seconds, and the screen will show’ RES.’
Continue holding until the desk goes down to its lowest level and comes back up slightly

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 5 minutes, it will stop operating to prevent damage from overheating. Wait for at least 15 minutes before making any further height adjustment.
---|---
E10| Sensor malfunction warning: Motor safety sensor cannot be detected. Please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.
E20| Overloading Warning: Over the max of loading weight. Power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline is detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.
–| Cable Disconnection Warning: Please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.

Customer Support

For Support or Feedback Write to Cambium Retail Pvt. Ltd.
Call: +91 9168001189 (9:00 AM – 5:30 PM Monday to Saturday)
Email: support@whitemulberry.online

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>