WHITE MULBERRY SEH04P Engineered Wood Motorized Height Adjustable Sit-Stand Desk Installation Guide
- June 1, 2024
- White Mulberry
Table of Contents
WHITE MULBERRY HEIGHT ADJUSTABLE
MOTORIZED DESK ASSEMBLY GUIDE
(INSTALLATION GUIDE)
SEH04P Engineered Wood Motorized Height Adjustable Sit-Stand Desk
-
It is recommended that at least two people cooperate to install.
-
Recommended installation on a clean flat floor.
It is recommended to check all parts before installation.
Make sure that the parts correspond to the instruction.
Installation & Safety Guideline
- Please read through Assembly Manual and parts list before any installation.
- Please check if there are any Missing parts or Damages
- Please choose a spacious and clean place, cover the floor with a paperboard to avoid any friction damage while proceeding with the installation.
- Please fasten all the screws tightly according to the Assembly Instruction
Disclaimers: Customer will be responsible for any damage or injury caused by misconduct of installation
Parts List
(The size will be according to regular measurements)
Note: Some screws have been pre installed in the hole.
-
Install Beam on Desktop with the help of Screw C & Screw D.
-
Insert the Leg Post in the Beam as shown in the image on both the side using Screw B.
-
Connect Leg Post with Foot Panel as shown in the image with the aid of screw A.
-
Insert the hexagonal rod into the corresponding hole in the Leg Post as shown in the image, and make sure it is inserted properly on both the ends and tighten the hexagonal nut and the set screw.
-
Install the control panel at the back of the desktop.
-
Connect the motor and the Power Adaptor to the Control Panel.
Attach the power adaptor at the bottom of the desktop and then connect it to the power supply with the cable that has been provided (as shown in the wiring diagram below).
-
Ensure all the Screws are tightened properly and turn over the Desk with someone’s aid and plug in the Desk to the Power Supply
PRECAUTION FOR USE
- Kindly refer to the functions, instruction when you are using the product.
- The product can only be seated when all the screws and parts are fastened. All parts should be checked routinely every three months to make sure no parts have loosen up.
- Please use the product on the flat floor. Away from humid environment, any fire hazards and direct sunlight.
- Children under 5 shall be accompanied by adults when using the product.
- Please do not stand on the table or use it as a ladder or footsteps.
- Please do not sit on the table in case of causing any danger.
- Please use a soft cloth to clean up the dust on the product before usage. Do not use rough cloth to wipe the product.
- For your own safety, please do not uninstall the internal components at will.
| Function | Instructions for use of control panel |
|---|---|
| Power on | Press and hold the until 5 seconds after the leg lift stops. At this |
time the controller displays “EST” and the reset begins. At this time do not
release the , lower the lifting leg slowly to the lowest end, until the
lifting leg all reach the lowest end and rebound lcm, release the , and
the reset operation is over. If you encounter an emergency during the reset
process, you can loosen the at any time, and the lifting leg will stop
running and the reset will terminate. After the reset is terminated, the reset
operation shall be performed again until the reset is successful, otherwise
other operations cannot be performed.
Reset| When “E10, E20, E60” appears or the desktop is not normal, long press
for three seconds until “RES” appears. After releasing, long press to reset
the desk automatically.
Manu-up| Press and display real height.
Manu-down| Press and display real height.
Memory position I| Press S , the panel displays “S-” , press 1 at this
time, and the current height will be memorized as level 1.
Memory position 2| Press S , the panel displays “S-” , press 2 at
this time, and the current height will be memorized as level 2.
Memory position 3| Press S , the panel displays “S-” , press 3 at
this time, and the current height will be memorized as level 3.
Call memory position 1| Press 1 , the desktop will move to the preset
memory position.
Call memory position 2| Press 2 , the desktop will move to the preset
memory position.
Call memory position 3| Press 3 , the desktop will move to the preset
memory position.
If you have any problems, please contact us on
+91 9168001189
support@whitemulberry.online
www.whitemulberry.online
Enjoy your
HEIGHT ADJUSTABLE
MOTORIZED DESK
Documents / Resources
|
WHITE MULBERRY SEH04P Engineered Wood Motorized Height Adjustable Sit-Stand
Desk
[pdf] Installation Guide
SEH04P Engineered Wood Motorized Height Adjustable Sit-Stand Desk, SEH04P,
Engineered Wood Motorized Height Adjustable Sit-Stand Desk, Wood Motorized
Height Adjustable Sit-Stand Desk, Height Adjustable Sit-Stand Desk, Adjustable
Sit-Stand Desk, Sit-Stand Desk
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>