White Mulberry 6545 Motorized Height Adjustable Desk with Drawer User Manual
- June 1, 2024
- White Mulberry
Table of Contents
White Mulberry 6545 Motorized Height Adjustable Desk with Drawer
Symbols
- 3 Height Position Memory
- Vertical Range: 72-118cm
| | | | CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.
---|---|---|---|---
Power Input 100V-240V| Speed 20 mm/s| Motion Noise ＜55dB| Load Capability 132
lbs / 60 kgs
Component List
-
Desktop (x1)
-
Crossbar (x1)
-
Left Side Plate (x1)
-
Right Side Plate (x1)
-
Left Table Leg (x1)
-
Right Table Leg (x1)
-
Transmission rod (x1)
-
Leg Base (x2)
-
Power (x1)
-
Power cord (x1
Hardware List
-
Screws M6×8mm (x8)
-
Screws M6×35mm (x8)
-
Screws M5×12mm (x6)
-
Screws M4×12mm (x2)
-
Allen Key S=2mm (x1)
-
Allen Key S=5mm (x1)
-
Cable Clip (x2)
Spare Parts
-
M6×8mm (x2)
-
M6×35mm (x1)
-
M5×12mm (x1)
-
M4×12mm (x1)
Assembly Instruction
Controller Introduction
Note:
The desk’s movement can be stopped at any time by pressing any button.
The height settings of the desk will remain even if the power is cut.
LED Display: Press any key once to wake up the display
Short press the button,the display flashes,Press any of memory key to save
the height.
Long press the button to raise the desk continually, and desk will stop when
the button was released or at the max height ( 118cm
Long press the button to lower the desk continually, and desk will stop when
the button was released or at the lowest height
( 72cm).
Memory button: Press the button until the number appears,it runs to
corresponding height and displays current position
Reset
Long press for 5 seconds, display RES and keep pressing until the digit height on the panel comes then lose the button. In the process, the desk goes down to the lowest and its height will be reset to 72cm.
Protection Mode Error Codes
Hot| Overheating Protection: When the motor has been working
continuously for 5 minutes, it will stop operating to prevent damage from
overheating. Wait for at least 15 minutes before making any further height
adjustment.
---|---
E10| Sensor malfunction warning: Motor safety sensor cannot be detected.
Please power off, unplug the cables of the controller, wait for 5 minutes,
then plug in the cables and connect the power again, and perform RES settings
again.
E20| Overloading Warning: Over the max of loading weight. Power off,
take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration,
impact, or incline is detected. If this detection is incorrect, follow the
reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC
adapter is being used, please power off, unplug the cables of the controller,
wait for 5 minutes, then plug in the cables and connect the power again, and
perform RES settings again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC
adapter is being used, please power off, unplug the cables of the controller,
wait for 5 minutes, then plug in the cables and connect the power again, and
perform RES settings again.
–| Cable Disconnection Warning: Please power off, unplug the cables of
the controller, wait for 5 minutes, then plug in the cables and connect the
power again, and perform RES settings again.
Engineering Mode
Change Displayed Unit( Un )| Long press the M button, “S–”shows and flashes.
Press M again and the display shows “Un”. Press M to select. Press or
to switch between“ ”(metric) or “ ” (imperial). Press M to save your choice.
---|---
Collision Force Detection( CF )| Long press the M button, “S–”shows and
flashes. Press M again and the display shows “Un”. Press or
to switch
to“CF”. Press M to select. Press or to switch between“OFF”,Low(L),
Normal (n) or Heavy (H) collision force detection. Press M to save your
choice.
Customer Support
For Support or Feedback Write to Cambium Retail Pvt. Ltd.
Call: +91 9168001189 (9:00 AM – 5:30 PM Monday to Saturday)
Email:support@whitemulberry.online
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>