milwaukee M18 Brushless Telescoping Pole Pruning Shears Cutting Blade User Manual
- June 1, 2024
- Milwaukee
Table of Contents
milwaukee M18 Brushless Telescoping Pole Pruning Shears Cutting Blade
Product Information
Specifications
- Product Name: M18TM Brushless Telescoping Pole Pruning Shears Cutting Blade
- Cat. No. : 48442770
- Manufacturer : Milwaukee Electric Tool Corporation
- Country of Manufacture : China
Product Usage Instructions
Installing the Cutting Blade
- Close the blades ensuring the cutting edge is covered by the lower jaw.
- Push the blade into the slot, aligning the holes.
- Secure the blade by tightening the T25 locking cap screw, the 13 mm hex head screw, and the T25 screw in order. Allow 24 hours for the threadlocker to cure before use.
Removing the Cutting Blade
- Disconnect the battery to prevent accidental activation.
- Loosen the T25 screw and then the 13 mm hex head screw using a scrench.
- Remove the T25 locking cap screw.
- Pull the blade out of the slot carefully.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of electric shock, fire and/or serious injury, read all safety warnings, instructions, illustrations, and specifications provided with this product, as well as those provided with the power tool, battery pack, and charger. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains- operated (corded) power tool or battery-operated (cordless) power tool.
Only use accessories specifically recommended for this tool. Others may be hazardous.
Removing/Installing the Cutting Blade
Replace the blade when it becomes dull or chipped. A blade is dull when the
blade edge appears rounded or damaged. Use only MILWAUKEE® blade Cat. No.
48442770.
DANGER: cutting edge. Laceration can occur.
- Close the blades. The cutting edge of the blade should be covered by the lower jaw.
- Remove battery to avoid starting the tool.
- To remove blade, use a scrench to first loosen the T25 screw, then the 13 mm hex head screw.
- Remove the T25 locking cap screw.
- Remove the T25 locking cap screw.
- To install blade, push blade into slot lining up the holes.
- Replace and tighten, in order, the T25 locking cap screw, the 13 mm hex head screw, and the T25 screw. This will secure the blade in place. For best results, after installation of a new locking cap screw allow 24 hours for the threadlocker to cure before using the tool.
WARRANTY – AUSTRALIA and NEW ZEALAND
Please refer to the Australian and New Zealand warranty supplied with tool. This warranty applies only to product sold by authorized dealers in Australia and New Zealand.
SERVICE – AUSTRALIA and NEW ZEALAND
MILWAUKEE prides itself in producing a premium quality product that is
Nothing But Heavy DutyTM. Your satisfaction with our products is very
important to us! If you encounter any problems with the operation of this
tool, please contact your authorized MILWAUKEE dealer. For a list of MILWAUKEE
dealers, guarantee or service agents please contact MILWAUKEE
Customer Service or visit our website. (Australia Toll Free Telephone Number
1300 645 928) (New Zealand Toll-Free Telephone Number 0800 645 928) or visit
milwaukeetool.com.au/milwaukeetool.co.nz
FAQ
Q: When should I replace the cutting blade?
A: Replace the blade when it becomes dull or chipped. A blade is
considered dull when the blade edge appears rounded or damaged.
Q: What should I do to ensure safety during blade replacement?
A: Make sure to keep your hands away from the cutting edge as it is
sharp and can cause lacerations. Always disconnect the battery before starting
the blade replacement process.
Q: Where can I find warranty information for Australia and New Zealand?
A: Please refer to the warranty supplied with the tool for Australian and New Zealand customers. The warranty applies only to products sold by authorized dealers in Australia and New Zealand.
References
- Milwaukee Tool | Official New Zealand Site of Milwaukee Tool | Nothing but HEAVY DUTY®
- Milwaukee Tool | Official Australia Site of Milwaukee Tool | Nothing but HEAVY DUTY®