HUHOMCO B0B65MDSDD Electric Mixer Instruction Manual
- June 1, 2024
- HUHOMCO
Table of Contents
HUHOMCO B0B65MDSDD Electric Mixer
FEATURE & USE
ELECTRIC MIXER is a handle electric tool with two-fold insulation,driven by the series generation. Its features are small in volume, light in weight, convenient to catch etc. It can be used in places which is moist and narrow. It can be used in the workshop with good conduct electricity, such as work high above the ground or metal frame etc.
INSTRUCTION OF SAFETY, USE MAINTENANCE
Read the explanation following before the tool got through power.
SAFETY
REGULARIZING WORKPIECE The work piece to be drilled must be regularized and
pay more attention to it when it is drilled through.
Use the plug correctly without changing the plug as one please and plug the
outlet with bare conducting wire directly not using the plug.
Be sure to take off the plug in time.
Not to use power wire without limited. Be sure not to lengthen or change the
power wire, not to carry the power wire touch heat source and oil. Prevent the
wire from being damaged.
OPERATION
-
USE ASSIGNED VOLTAGE The voltage in the circuit must be not more than 10% at the data plate assignment before using it.
-
CHECK BEF ORE BEING USED Let the tool have nonloading for one minute and see whether the function of the transmission position is flexible and there is abnormal noise and the screws become flexible and fall off and the inverting sparkle is normal or not.
-
PREVENT THE TOOL FROM OVERLOAD The head of the drill must be sharp. When you are drilling, you should not be too tough. If the rotation speed is reduced abnormally, you should reduce to exert yourself. If the drill stops suddenly or gets stuck, you must turn off the power
-
Change the brush in time if the brushes are too damaged to use.
Change them both at same time, otherwise the brushes and the inverter will be in loose contact even sparkle around or the inverter can be damaged, Sometimes the armature would be burnt.
It can not be used in the following condition. If you find the insulate is damaged, the power wire or electric cable case is broken, the plug and outlet is broken, and it works continually. The sparkle appears seriously etc, you should repair immediately. It can’t be used before being repaired. -
USE THE TOOL CAREFULLY The tool used should be placed softly in order not to be shocked.
MAINTENANCE
-
ADD OIL IN IT of ten The drill is a speed working tool. The lubrication grease is volatilized easily so the grease in reduction case and bearing must often be kept clean and add or change it anytime needed.
CHECKING AND MAINTENANCEONITREQUENTLY The drill should be checked, repaired day to day and see whether the power wire, the inner wiring, the plug and the switch work well or not. Pay attention to everything such as whether the insulation resistance works normally,the handle is flexible, the inverter and brushes are well contacted, the armature winding and the stator winding are in short circuit or broken circuit, and the bearing, the other moving parts are damaged etc. -
EACH PART SHOULD BE WELL KEPT AND WHEN YOU WANT TO CHANGE THE PART, USING THE SAME ONES When the drill needs taking apart and checking, do keep each part including insulation and casing pipe. If they are damaged you must change the new one and the same one. Be sure not to use the substitution materials which is worse than one used and the part which does not agree with the standard. When fixing ,you must put the parts in their proper position as usual and should not omit any of them.
-
BE CAREFUL OF THE INSULATION RESISTANCE The drill not to be used for long or to have been used in damp condition must be tested
In its wiring of the insulation resistance with a 500 million ohm meter.
If the winding and iron center is less than 2 million ohms, you must make drying treatment to the wingding until more than 2 million ohms. -
STORED CAREFULLY The drill should be kept in a dry clean place and without any corrosive gases.
ACCESSCRIES
If the manufactured by our factory is damaged or can’t work normally for the quality, we will repair it free within one year since the date of manufacture or being bought within six months.
NOTE: To be sure obey the rules and use and keep it correctly and Disassemble by yourself except to change the brushes.
FOLLOWING GARD FOR QUALITY using Circumstances.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>