VALUE MC-GE-MM Gigabit Ethernet Media Converter User Manual

June 1, 2024
VALUE

VALUE Gigabit Ethernet Media Converter

21.99.1199

User manual

Please read the manual before using!

The manual may be changed without prior notice.

Overview

The Gigabit Ethernet Media Converter converts 10/100/1000Base-T electrical signals to 1000Base-FX optical signals. It provides an economic way to extend the network transmission distance from 100m over copper cables to 100km over fiber optical cables. It complies with IEEE802.3 10Base-T, IEEE802.3u 100Base- TX, IEEE 802.3ab 1000Base-T, and IEEE802.3z 1000Base-X. It supports auto full/half duplex, auto MDI/MID-X and can be used for many different applications.

Item Specifications
MC-GE-MM 10/100/1000M, MMDF 550m~2km, SC/FC/ST
MC-GE-SM 10/100/1000M, SMDF 20km~120km, SC/FC/ST
MC-GE-WDM 10/100/1000M, SMSF20km~120km, SC/FC/ST
MC-GE- SFP 10/100/1000M, SFP slot
Packing list

Make sure that you receive the full package in good condition. If anything is missing or damaged, please contact us.

Gigabit Ethernet Converter Media     1

Power Adaptor (external)                    1

Power Line (internal)                           1

User Manual                                        1

Technical parameters

Standard

| IEEE802.3 10Base-T, IEEE802.3u,100Base-TX/FX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-X, IEEE802.3x Flow Control
---|---

Ports

| 1x 10/100Base-Tx
1x 100B/10000ase-Fx| 2x 10/100/1000Base-Tx
1x 1000Base-Fx| 4x 10/100/1000Base-Tx
1x 1000Base-Fx

Reach

| UTP: ≤250m @10Base-Tx; ≤100m @100/1000Base-Tx
Fiber: ≤2km @MMF; ≤120km @SMF

Connector

| Ethernet port: RJ45
Fiber: SC/ST/FC/LC(SFP) available

Voltage input

| DC5V| DC5V| DC5V
Power| <3W| <3.5W|

<5W

Operating

| -10~+65℃; 10%~90%, non-condensing
Storage| -40~+75℃; 5%~90%, non-condensing
Dimension
External:
Card:Internal:| 71 9626mm
1148826mm
14011030mm| 71 9626mm
1148826mm
/| 71 9626mm
1148826mm
/

Optical Parameters

Options

| wavelength| Reach| power|

Sensibility

---|---|---|---|---

MC-GE-MM

|

850nm

| 550m| -10~-3dBm|

≤-17dBm

MC-GE-MM

|

1310nm

| 2km| -10~-3dBm|

≤-17dBm

MC-GE-SM

|

1310nm

| 20Km| -9~-3dBm|

≤-22dBm

MC-GE-SM

|

1550nm

| 40Km| -5~0dBm|

≤-24dBm

MC-GE-SM

|

1550nm

| 60Km| -6~+1dBm|

≤-24dBm

MC-GE-SM

|

1550nm

| 80-100Km| -2~+3dBm|

≤-24dBm

MC-GE-WDM

|

1310/1550nm

| 3km| -12~-4dBm|

≤-23dBm

MC-GE-WDM

|

1310/1550nm

| 10~20km| -9~-3dBm|

≤-23dBm

MC-GE-WDM

|

1310/1550nm

| 40~60km| -2~+3dBm|

≤-23dBm

MC-GE-WDM

|

1490/1550nm

| 60~100km| -2~+3dBm|

≤-23dBm

LED indicator

The LED indicators facilitates to monitor the working status and troubleshoot. Refer to the below table for the status of LED indicator.

LED

|

Status

| Description
---|---|---

FX LINK/ACT

|

On

| Fiber port connected and link good

Blink

| Data sending and receiving on fiber port

Off

| Fiber port disconnected or link error

TX LINK/ACT

|

On

| Ethernet port connected and link good

Blink

| Data sending and receiving on Ethernet port

Off

| Ethernet port disconnected or link error

1000

|

On

| Data rate is 100Mbps on Ethernet port

100

|

On

| Data rate is 100Mbps on Ethernet port

FDX

|

On

| Full duplex on Ethernet port

PWR

|

On

| Power supply is ok

Off

| Power supply error

  Caution

  1. The media converter is for indoor use;
  2. Cover the dust cap when the fiber port is not used;
  3. DON’T stare at the fiber port with naked eyes when it is working, or it may hurt your eyes;
  4. WDM media converter should be in pairs.
Installation
Ethernet Port Connection

Connect the network device (work station, hub or switch) to the RJ-45 jack of the media converter by CAT5e or better TP cable. Please use quality RJ-45 and well-made patch cords. It auto identifies MDI or MDI-X cable.

1000Base Tx RJ45 Pinouts

MDI/MDI-X Pinouts

Pin

| Signal| Pin| Signal
---|---|---|---
1| TRD(0)+| 5|

TRD(2)-

2

| TRD(0)-| 6| TRD(1)-
3| TRD(1)+| 7|

TRD(3)+

4

| TRD(2)+| 8|

TRD(3)-

8-pin RJ45

Fiber Port Connection
For dual fiber port, connect TX of media converter with the RX of the network device, and RX of the media converter with the TX of the network device by a duplex fiber optic patch cord.

For single fiber optical port, connect the optical port of media converter with that of the network device by a simplex fiber optic patch cord.

Power connections
Connect the DC socket of media converter, and power supply with the power adapter.

We recommend to use our default power adapter. If not, make sure that the rated input voltage of power adapter is 5V.

Trouble shooting
  1. Power LED is OFF
    If installed on a desktop, check that the power adapter is securely connected.
    If installed in our chassis, check that the unit is fully seated in the slot.
    Verify that the power outlet has power output.
    Try using another power adapter.

  2. TX LINK/ACT LED is OFF
    Check if the connected device is powered ON and operating properly.
    Check that the TP cable is securely connected.
    Make sure that the TP cable does not exceed 100 meters.

  3. FX LINK/ACT LED is OFF
    Check if the connected device is powered ON and operating properly.
    Check that the fiber is securely connected.
    Make sure the TX and RX port is connected correctly.
    Test if the attenuation on the fiber cable does not exceed the acceptable values.

  4. FX LINK/ACT is ON, but still problem in communication
    Check if the data rate of the both sides is 100Mbps
    Check if the duplex mode of the both sides is same
    Check if wavelength of the both sides is same
    Check if the loss budget off fiber is not exceeded.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals