Great Value D303353GQ110 LED Bluetooth Speaker Utility Light Medium Base Adjustable Blades User Guide
- June 10, 2024
- Great Value
Table of Contents
Great Value D303353GQ110 LED Bluetooth Speaker Utility Light Medium Base
Adjustable Blades
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
- Suitable for damp location.
- Do not use with dimmers.
- Not for use in totally enclosed luminaires.
- Added weight of the device may cause instability of a free-standing portable luminaire.
- This device is not intended for use with emergency exits.
- Do not make or alter open holes in an enclosure of wiring or electrical components during kit installation.
- The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installations.
WARNING: Risk of fire or electric shock. LED retrofit kit installation
requires knowledge of luminaires electrical systems. If not qualified, do not
attempt installation.
Contact a qualified electrician.
WARNING: Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does exceed the input rating of the luminaire.
WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
CAUTION:
Light is extremely bright. Avoid looking directly at LED’s.
FEATURES
- Rugged Plastic Lens
- Suitable for Damp Locations
- ETL Certified
- Equipment has been tested and found to comply with the limits pursuant to Part 15, Subpart B of the FCC Rules. These limits are designed to provide reasonable protection against harmful electrical interference in a residential installation.
INSTALLATION
-
Carefully remove the utility light from the packaging. Check for any defects or damage.
CAUTION: Before beginning installation turn off the circuit breaker and light switch. -
Flush Installation: Screw utility light clockwise into E26 socket to tighten. Adjust fins as desired to direct light where needed. The maximum adjustable angle is 90°. (Figure 1)
NOTE: Be careful not to over-tighten. -
Recessed Fixture Installation: Add extension adapter (Not Included) as needed. Screw the extension adapter into the E26 socket until tight, then secure the utility light to extension adapter and tighten. (Figure 2)
-
Restore power to the fuse box and turn the light switch on to activate the fixture.
OPERATING
- Press Bluetooth Activation Button for 2 seconds to turn on speaker and activate Bluetooth function.
- Bluetooth Speaker will enter pairing mode. Activate Bluetooth on your device and find device named “D303353GQ110”. Press to pair.
- Once paired, select audio from your device and play through the light speaker.
- Press Bluetooth Activation Button quickly to pause or play music.
- Press Bluetooth Activation Button for 2 seconds to turn off speaker.
- Connection distance within 65 feet(20m) of open environment.
NOTE: Adjust the volume with your device.
Two light mode(TWS): Mark sure lights bluetooth are not connect with any device, press both buttons to turn on the speakers, you will hear a “click” and they are connected. Then repeat above bluetooth operation.
NOTE: Light have memory function. The bluetooth will remain the status same as when it is turn on last time.
TROUBLE SHOOTING
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Light will not come on. |
- Light switch is turned off.
- **** The light is not properly installed.
- **** Fuse is blown or circuit breaker is turned off.
|
- Check if the Power switch is set to ON.
- **** Make sure light is completely screwed into E26 base.
- **** Check if the GFCI has tripped. Check if the 120 Vac circuit breaker has tripped. Reset the GFCI or circuit breaker.
FCC WARNING:
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTES: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receive
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
RF Exposure: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
TRADEMARK ATTRIBUTION FOOTNOTE
Whenever the Bluetooth Trademarks are used in a particular piece , they must
be attributed with an appropriate trademark footnote.
The recommended attribution footnote is as follows:
®“The Bluetooth word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. And any use of such marks by INTERNATIONAL DEVELOPMENT
COMPANY is under license. Other trademarks and trade names are those of their
respective owners.”
NOTE:
®The Bluetooth brand elements may not be used in a fashion or manner that
could impair or otherwise damage the goodwill associated with the Bluetooth
brand or the ® Fellow Adopters (International Development Company). The
Bluetooth brand elements ® shall therefore not be used in connection with
products and services that do not ®enable any Bluetooth wireless functionality
or in connection with unlawful, obscene, pornographic, excessively violent,
hazardous, or otherwise poor-taste activities.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>