Edinburgh 4019071 Bedside Luxury Co Sleeper Instruction Manual
- June 1, 2024
- Edinburgh
Table of Contents
Bedside Luxury Co Sleeper
Instruction Manual
EN1130:2019
4019071 Bedside Luxury Co Sleeper
IMPORTANT:
READ CAREFULLY
KEEP FOR FUTURE REFERENCE
Dear Parents:
Thank you for purchasing the bedside crib.
Please read and follow all instructions before using the bedside Crib.
WARNING
-
DO NOT USE THIS PRODUCT WITHOUT READING THE INSTRUCTIONS FOR USE FIRST.
-
STOP USING THE PRODUCT AS SOON AS THE CHILD CAN SIT OR KNEEL OR PULL ITSELF UP.
-
DO NOT USE MORE THAN ONE MATTRESS IN THE PRODUCT.
-
PLACING ADDITIONAL ITEMS IN THE PRODUCT MAY CAUSE SUFFOCATION.
-
DO NOT PLACE THE PRODUCT CLOSE TO ANOTHER PRODUCT, WHICH COULD PRESENT A DANGER OF SUFFOCATION OR STRANGULATION, E.G. STRINGS, BLIND/ CURTAIN CORDS, ETC.
-
NEVER LEAVE THE CHILD UNATTENDED IN THE BEDSIDE SLEEPER. ALWAYS PROVIDE
-
THE SUPERVISION NECESSARY FOR THE CONTINUED SAFETY OF YOUR CHILD.
-
THE PRODUCT SHOULD BE PLACED ON HORIZONTAL FLOOR. IT IS DANGEROUS TO PLACE THE PRODUCT ON A RAISED SURFACE SUCH AS A TABLE.
-
DO NOT USE THE PRODUCT IF ANY PART IS BROKEN, TORN, OR MISSING.
-
ONLY AN ADULT SHOULD ASSEMBLE, FOLD AND UNFOLD THE BEDSIDE SLEEPER.
-
BEFORE ASSEMBLY, CHECK THAT THE PRODUCT AND ALL OF IT’S COMPONENTS HAVE NOT BEEN DAMAGED DURING TRANSPORTATION. SHOULD ANY PART BE DAMAGED, DO NOT USE AND KEEP OUT OF REACH OF CHILDREN.
-
ENSURE USERS OF THIS PRODUCT ARE KNOWLEDGEABLE ON IT’S CORRECT OPERATION.
-
DO NOT POSITION THE COT NEAR WALLS AND OBSTACLES TO PREVENT ENTRAPMENT.
DO NOT ADJUST THE PRODUCT WITH THE CHILD INSIDE. -
DO NOT MOVE THE PRODUCT WITH THE CHILD INSIDE.
-
DO NOT USE THE PRODUCT WITH MORE THAN ONE CHILD AT A TIME.
This product is intended for use for babies aged between 0 and 5 months,
weighing up to a maximum of 9kg. Stop using the product as soon as the child
can sit or kneel or pull itself up.
Before use in ‘bedside sleeper’ mode (fixed to the bed), make sure the product
is securely attached and positioned.
When the product is used in ‘bedside sleeper’ mode (fixed to the bed), make
sure the connection belts are hooked and tensioned properly, before laying
child in the sleeper. The product must be secured to the parent’s mattress and
no gaps between the product and the adult’s mattress must be present.
DO NOT use the sleeper without the support frame. Keep the fastening belts out
of reach of children.
The thickness of the uncompressed mattress shall not exceed 40mm. The upper
surface of the non-compressed mattress must be at least 200 mm lower than the
upper surface of the lowest side of the bedside sleeper.
DO NOT use mattress other than the one supplied by the manufacturer.
NEVER use a water mattress with this product. Incorrect mattress can cause
death.
DO NOT leave any object inside the product that could reduce its depth.
Be aware of the risk of burning cigarettes, open fires and other sources of
strong heat, such as electric bar heaters, gas fires etc. in the near vicinity
of the crib.
The product is ready for use only when all locking mechanisms are engaged.
Check carefully that these are engaged before use.
Failure to follow these warnings and instructions could result in serious
injury or death.
NEVER use the bedside sleeper in an inclined position.
NEVER use the bedside sleeper bassinet in bedside sleeper position
without the strap attached and locked as shown. Failure to use this attachment
system could result in serious injury or death to the infant. Make sure all
straps are secured and tight. Check straps before each use.
SUFFOCATION HAZARD: Discard all packing materials immediately after
opening.
Plastic bags and ties may cause suffocation or choking.
FALL HAZARD: To help prevent falls, do not use this product when infant
begins to push up on hands and knees or has reached manufacturer’s recommended
maximum weight of 9kg, whichever comes first.
WARNING
SUFFOCATION HAZARD – INFANTS HAVE SUFFOCATED:
- In gaps between extra padding and side of the bassinet/ cradle, and
- On soft bedding.
Use only the pad provided by manufacturer. NEVER add pillow, comforter, or another mattress for padding.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed
on their backs to sleep, unless otherwise advised by your physician.
A bedside sleeper is designed to provide a sleeping area for an infant until
he or she begins to push up on hands and knees or approximately 5 months of
age. Move your child to another sleeping product when your child reaches this
stage.
STRANGULATION / SUFFOCATION HAZARD: The top edge of the lowering bar must be
below the top of the adult mattress when used as the bedside sleeper. The
level of the bedside sleeper bassinet mattress must be a minimum of 12cm below
the top edge of
the lowering bar. NEVER raise the level of the bedside sleeper bassinet
mattress.
NEVER use plastic shipping bags or other plastic film as mattress covers not
sold and intended for that purpose. They can cause suffocation.
Make sure all straps are secured and tight when used in the bedside sleeper
position.
Tighten straps periodically.
WARNING
ENTRAPMENT HAZARD – TO PREVENT DEATH FROM ENTRAPMENT, BEDSIDE SLEEPER MUST BE
PROPERLY SECURED TO ADULT BED USING THE ATTACHMENT SYSTEM
There shall never be a gap between the lower side of the bedside sleeper and
the mattress of the adult bed.
Check the tightness of the attachment system before each use by pulling the
bedside sleeper in a direction away from adult bed.
If there is any gap between the bedside sleeper and the adult bed, DO NOT use
product.
DO NOT fill the gap with pillows, blankets or other items that are suffocation
hazards.
ALWAYS read and follow assembly instructions for each product use mode
(bedside sleeper, bassinet).
ALWAYS use ALL required parts for each use mode. Check instruction manual for
a list of required parts. Periodically check product for loose, damaged, or
missing parts.
The straps assembly must always be used in bedside sleeper mode.
NEVER use this product if there are any loose or missing fasteners, loose
joints, broken parts, or torn mesh / fabric. Check before assemblv and
periodicallv during use.
DO NOT substitute parts.
All assembly fittings should be always be tightened properly and that care
should be taken that no screws are loose, because a child could trap parts of
the body or clothing(e.g. strings, necklaces, ribbons for babies’ dummies,
etc.) which would pose a risk of strangulation.
Assemble product according to manufacturer’s instructions for ANY use mode –
bedside sleeper as well as the bassinet.
WARNING- To avoid hazards from the child’s neck being caught on the top rail
on the side that is next to the adult bed, the top rail must not be higher
than the adult bed mattress.
NEVER permit bedding from the adult bed to extend into the bedtime sleeper.
DANGER! -NEVER leave your infant in the product without the TOP HORIZONTAL
RAIL installed in the uppermost position, unless securely attached to the
adult bed.
To prevent a suffocation hazard from entrapment, the bedside sleeper shall be
properly secured to the adult bed using the attachment system.
Failure to use this securing system will allow the bedside sleeper to move
away from the adult bed and could result in the infant falling out of the
bedside sleeper.
Use only the attachment system sold with this crib, do not use other
attachment system.
STRANGULATION HAZARD: To avoid the risk of your child being strangled the
attachment system to the adult’s bed shall always be kept away from and out of
the crib.
DO NOT place the product near a window where cords from blinds or drapes may
strangle a child. Keep the bassinet away from stoves, heaters, camp fires and
other hazards.
DO NOT allow children to climb or play on or under unit in any configuration.
Young children should not be allowed to play unsupervised in the vicinity of
the crib.
FALL HAZARD: Remove infant from the bedside sleeper before starting any
conversions.
Always make sure all top and bottom rails are securely locked, in all
configurations, before putting an infant child into the unit.
To prevent serious or fatal injury from falls always keep child within arm’s
reach.
- NEVER leave your child unattended. The crib should be locked in the fixed position when the child is left unattended.
Strings can cause strangulation! NEVER place items with a string around a
child’s neck, such as hood strings or pacifier cords. NEVER suspend strings
over product or attach strings to toys.
The bedside sleeper is designed for use only with adult beds that are between
50.5-62.5cm from floor to top of adult mattress.
ASSEMBLY CONTENTS:
You have received 1 box. Please check the content of the box against the list
below. If anything is missing, please contact Customer Service.
Supplied loose in box:
There are no accessories recommended for use with this Bedside Sleeper.
ASSEMBLY / OPERATION INSTRUCTIONS
TO ASSEMBLE FRAME AND BEDSIDE SLEEPER LINER…
-
a) Put the connecting bar in storage cover and screw the bolt (M6*44mm X4pcs) to connect wooden legs and bars
-
a) Push the middle support frame tubes into the frame till you hear a ‘click’ sound.
-
a) Lay the top frame topside down, and push the middle frame in till you hear a ‘click sound’.
-
a) Rest the top frame on wooden legs by sliding into slot.
-
a) Screw the lock cover into wooden legs.
-
a) Wrap liner flaps around middle frame and secure with Velcro strips.
-
a) Insert the wheels on to bottom of legs.
-
a) The assembled product should be as shown.
WARNING
Only Lése the mattress sold with this crib, do not add a second mattress on
this one, suffocation azards.
TO LOCK WHEELS:
- a) Press lock down to lock wheels in place.
- a) Lift lock up to release wheels.
TO ADJUST HEIGHT OF BEDSIDE SLEEPER…
- a) The sleeper can be adjusted into 3 different heights. Revolve the round cover till it is loose , hold the top frame and slide inward and lift to the desired height. Repeat on the other side.
WARNING
HEIGHT ADJUSTMENT MECHANISMS MUST ALWAYS BE SET TO THE SAME HEIGHT SETTING TO
ENSURE A FLAT AND SAFE SLEEPING ENVIRONMENT IS MAINTAINED. AN INCLINED SETTING
IS NOT SAFE.
TO TURN ROCKING MODE…
- a) Slide the button inward and turn the gear forward to unlock.
Repeat on the other side
WARNING
a) DO NOT USE THE ROCKING MODE WHEN THE CHILD IS UNATTENDED.
b) THE MAX INCLINATION IS 10°. THE CHILD MAY GET INJURED IF THE AMPLITUDE OF
THE SWING IS EXCESSIVE AND MAY POSE RISKS TO OTHER CHILDREN.
c) LOCATE THE CRIB WHERE THERE IS NO RISK OF SWING IMPACT.
d)THE PRODUCT SHOULD BE PLACED ON HORIZONTAL FLOOR. UNEVEN SURFACES CAN CAUSE
INSTABILITY OF THE PRODUCT.
TO FIX THE BED IN BEDSIDE SLEEPER MODE…
-
a) Unzip the front panel on both sides. Slide the bar lever back and lift on both sides.
-
a) Remove the tube and put the front panel down. Secure with elastic tabs on middle frame support.
2a) Clip the fixing belts to the side support frame.
-
a) Move the sleeper close to the parent’s bed and check the height of the sleeper compared with the mattress on the bed.
-
b) The side support of the sleeper should always be placed close to the parent’s mattress and the mattress should always be aligned with the height of the S side support for restraint of the sleeper.
-
a) In order to fix the co-sleeper to the parent’s bed in co-sleeping mode, use the attached pair of fixing belts provided.
-
a) Slide the straps between the top mattress and the base using a back and forth ‘sawing’ motion and at the same time pulling downward until the straps and anchor plates are in the desired position.
CAUTION! ENSURE THE FIXING BELTS ARE STRAIGHT!
-
a) The anchor plates should appear like the opposite picture once they are assembled between the mattress and the base.
-
a) Tighten the loop by pulling the belts firmly. The strap must be horizontal as possible.
Make sure the strap is in line with bed frame.
8b) Adjust the belts separately until the sleeper is firmly in contact with the parent’s mattress.
8c) Store any excess of belts between the mattress and the base.
WARNING
- Before every use always check to make sure there is no space between the parent’s mattress and the side of the sleeper.
- If there is, pull the belts firmly to tighten until there’s no space and the permitted condition of use has been restored.
- Use of product is only permitted with beds and/or mattresses with straight sides, use of the product with round mattress and or water bed is not permitted.
- When the product is used in the bedside sleeper mode, it should always be fitted to the long side of access to the bed, do not fix the product to the bed or bottom of the bed.
- This bedside sleeper cannot be used with a recessed bed
HOW TO CARE FOR YOUR BABY BEDSIDE SLEEPER
Cleaning
This product has been designed and developed with safety, comfort and
functionality in mind. Please take the time to read this manual carefully
before using this product and keep it in a safe place for future reference. To
ensure the long-lasting use of your bedside sleeper, do not use solvents,
abrasives or aggressive cleaning products. After each wash check the
resistance of the fabric and the stitching. For washing of the fabric,
carefully comply with instructions indicated on the label (listed below).
| Hand wash in cold water
---|---
| DO NOT bleach
| DO NOT tumble dry
| DO NOT iron
| DO NOT dry clean
Maintenance
Always check parts regularly for tightness of screws, nuts and other fasteners— tighten or replace if required. The bedside sleeper and the mattress have a resistant fabric cover which is completely removable and washable. The removal of the fabric should be carried out by an adult only. On a regular basis check the condition of the product and presence of any possible damage. In the case of damage do not use and keep it out of the reach of children. To maintainthe safety of your bedside sleeper seek prompt repairs for bent, torn, worn or broken parts. If you have any difficulties in assembling the sleeper, please contact Our Service Department.
Supplied by
Baby Factory (NZ) Lid
www.babyfactory.co.nz
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>