Edinburgh 4016933 Classic Co-Sleeper Instruction Manual
- June 4, 2024
- Edinburgh
Table of Contents
Classic Co-Sleeper
Instruction Manual
Model Number: 4016933
IMPORTANT!
READ CAREFULLY AND KEEP IT FOR FUTURE REFERENCE
WARNING
Failure to follow these warnings and instructions could result in serious
injury or death.
- Read all instructions before assembling and using the product.
- FALL HAZARD- To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached the manufacturer’s recommended maximum weight of 19.8lbs(9KG), whichever comes first.
SUFFOCATION HAZARD
Infants have suffocated:
- In gaps between extra padding and the side of the bassinet/cradle, and
- On soft bedding Use, only the pad provided by the manufacturer. NEVER add a pillow, comforter, or another mattress for padding.
- To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep unless otherwise advised by their physician.
- FALL HAZARD-Always check that the bassinet is securely locked on the base/stand by pulling upwards on the bassinet bed.
- If a sheet is used with the pad, use only the one provided by the bassinet or cradle manufacturer or one specifically designed to fit the dimension of the bassinet or cradle mattress.
- Strings can cause strangulation Do not place items with a string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a bassinet or cradle or attach strings to toys
WARNING
- Keep instructions for future use.
WARNING
Entrapment Hazard – To prevent death from entrapment, beside sleeper must be
properly secured to the adult bed using the attachment system.
- There must be no more than a 1/2 in.(13mm)gap between the bedside sleeper and the adult bed.
- Check tightness before each use by pulling beside the sleeper in a direction away from the adult bed.
- If the gap exceeds 1/2 in.(13mm). DO NOT use the product. Do not fill the gap with pillows, blankets, or other items that are suffocation hazards.
WARNING
Always use ALL required parts for each use mode. Check the instruction manual
for a list of required parts. Periodically check the product for loose,
damaged, or missing parts.
WARNING
- Always read and follow assembly instructions for each product use mode (bedside sleeper, bassinet ).
WARNING
- To avoid death from the infant’s neck being caught on the top rail on the side that is next to the adult bed, the top rail must be no higher than the adult bed mattress.
WARNING
- Assemble the product according to the manufacturer’s instructions for ANY use mode bedside sleeper as well as the bassinet modes
WARNING
- A bedside sleeper is designed to provide a sleeping area for an infant until he or she begins to push up on hands and knees or approximately 5 months of age. Move your child to another sleeping product when your child reaches this stage.
- The attachment system must always be used in bedside sleeper mode.
- Only the bedside bed mode can be put down the side bezel.
WARNING
- This bedside sleeper is designed for use only with adult beds that are between 21.5 and 26.5 inches (546mm to 673mm) from floor to top of the adult mattress.
WARNING
-
DO NOT use a bedside sleeper if any parts are missing, damaged, or broken. Contact Baby Factory for replacement parts and instruction literature if needed. DO NOT substitute parts.
-
The type of adult beds (Below Fig.) with which the bedside sleeper CAN OR CANNOT be used.
-
The bedside sleeper can be used for an aligned adult bed only. Meanwhile, the distance from the lowest bottom side of the aligned adult bed(the drop side) to the ground should be more than 20cm.
Parts List
How to assemble the crib?
-
Open bed cradle as shown in figure 1.
-
Insert the transverse supporting tube into the plastic joint until you heard a “click” sounds shown in figure 2.
-
Assembly of the storage bag as shown in figure 3. Insert the storage bag supporting tube into the plastic joint until you heard a “click” sound.
-
Place the mattress on the bassinet and ensure it is fitted securely as shown in figure 4.
-
Stick the velcro goes through the hole as shown in figure 5.
-
The bassinet is now fully installed as shown in figure 6.
How to use the drop side?
-
Unsnap the button, and unzip the zipper on both sides of the guard rail as shown in figure 7.
-
Push both locking mechanisms inwards & lift upwards the guard rail slightly as shown in figure 8.
-
Disconnect both ends of the guard rail from the bassinet as shown in figure 9.
-
The drop-side co-sleeper is ready for your kid– as shown in figure 10.
DANGER! Always completely raise the drop side when not attached to the adult s bed.
How to use the drop side?
WARNING: The attachment system must ALWAYS be used beside sleeper mode.
- Lower the guard rail, and align the crib directly next to the parent bed.
- Pass the safety strap ( attachment system) underneath the mattress of the bed and around the bed frame, make sure the strap pieces are set upright between the mattress and the edge of the bed as shown in figure 2.
- Secure another end of the safety strap male buckle by connecting the female buckle, then tighten the strap belt.
Make sure the mattress, co-sleeper, and strap belt pieces are aligned.
WARNING
How to adjust the height?
-
Grasp the bassinet then lift up to the desired height as shown in figure 11.
-
Grasp the plastic height adjustable handle on both brackets down to the desired height as shown in figure 12.
Warning: When adjusting the height position, make sure the angle of the inclination of the crib base and end (head to feet) shall not be greater than 10. Or the difference between left and right gears of the height shall not be greater than 2.
How to take off the bassinet cover?
-
Disconnect the zipper on the top rail from the bracket as shown in figure 13.
-
Take off the bassinet set from the bracket as shown in figure 14.
How to fold the baby crib?
-
Remove the transverse supporting tube from the bassinet bracket as shown in figure 15.
-
Disassemble both storage bag supporting tubes from the bracket as shown in figure 16.
-
Fold both brackets as shown in figure l7.
-
The baby crib is folded up as shown in figure 18.
Cleaning & Maintenance
Frame: Wipe the metal frame with a soft, clean cloth and mild soap
Mattress: Remove from mattress foam, Soft Machine wash or hand wash with
cold water, gentle cycle. No bleach, Tumble dry, Low heat.
Supplied by:
Baby factory NZ Ltd
58 Stonedon Drive, East Tamaki,
Auckland, New Zealand
www.babyfactory.co.nz
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>